Sony XKS-C9111 User Manual page 447

• On the XVS-7000, FC9 to FC16 cannot be used.
• In 4K format, only FC1, FC5, FC9, and FC13 can be
configured.
Assigning an input signal to an FC channel
You can assign a signal to be converted by the format
converter to an FC channel.
1
In the Engineering Setup >Switcher >Input menu
(7332), press [Internal FC].
The Internal FC menu (7332.5) appears.
2
Press [FC Input Select].
The FC Input Select menu (7332.3) appears.
The status area shows the FC channel list on the left
and the list of input signals that can be assigned to FC
channels on the right.
3
In the list on the left, select the target FC channel to set.
4
In the list on the right, select an input signal.
5
Press [Set].
To set the source name of the converted input
signal
1
Select the target FC channel to set, and press [FC
Name].
2
Enter a name of up to 16 characters in the keyboard
window, and press [Enter].
Setting the conversion format
You can set the signal format of inputs to convert by the
format converter.
The conversion format is set in the following groupings,
depending on the switcher signal format.
• 3840×2160P, 1080P: 4-channel groups (FC1 to FC4,
FC5 to FC8, FC9 to FC12, FC13 to FC16)
• 1080i, 720P: 8-channel groups (FC1 to FC8, FC9 to
FC16)
Notes
• When the switcher signal format is 3840×2160PsF or
1080PsF, input signal format conversion is not available.
• When the switcher signal format is 1080P, the signal
formats that can be converted vary depending on the
720P converter setting.
For details about the 720P converter, see "Enabling/
disabling the 720P converter" (page 461).
• On an internal format converter, the format of only the
XKS-S8110 SDI Input Connector Board input signals
can be converted.
Supported formats
The supported conversion formats are given below.
Note
Field frequency and frame frequency conversion is not
supported.
Switcher signal format
3840×2160P
(Level A, 2SI)
3840×2160P
(Level A, SQD)
1080P
(Level A)
1080i
720P
a) Input signal without format conversion
b) Selectable when the 720P converter is disabled
c) Selectable when the 720P converter is enabled
d) When the switcher signal format frequency is 59.94, only 480i is
selectable. When the frequency is 50, only 576i is selectable.
1
In the Engineering Setup >Switcher >Input menu
(7332), press [Internal FC].
The Internal FC menu (7332.5) appears.
2
Press [FC Format].
The FC Format menu (7332.6) appears.
The status area shows the FC channel list on the left
and the supported conversion signal format list on the
right.
3
In the list on the left, select the target FC channel to set.
Select one of the four target channels or eight target
channels to set.
4
In the list on the right, select the signal format.
447
Input signal format
• 3840×2160P (Level A, 2SI)
• 3840×2160P (Level B, 2SI)
• 3840×2160P (Level A, SQD)
• 3840×2160P (Level B, SQD)
• 1080P (Level A)
• 1080P (Level B)
• 1080i
• 3840×2160P (Level A, 2SI)
• 3840×2160P (Level B, 2SI)
• 3840×2160P (Level A, SQD)
• 3840×2160P (Level B, SQD)
• 1080P (Level A)
• 1080P (Level B)
• 1080i
a)
• 1080P (Level A)
b)
• 1080P (Level B)
b)
• 1080i
c)
• 720P
a)
• 1080i
• 720P
d)
• 576i
d)
• 480i
• 1080i
a)
• 720P
d)
• 576i
d)
• 480i
a)
a)