Nikon SMZ800N Instruction Manual page 12

1 Power shutdown
To prevent electric shock and/or malfunction,
always turn off the power switch(es) for this product
and the peripheral devices (press to the "O"
position) and unplug the power cord from the wall
outlet before assembling this product, connecting
or disconnecting cables, replacing lamps, or
cleaning the zooming body and the objective.
2 Do not look into the LED light
The P-CI Coaxial Epi Illuminator, C-FDF Flexible
Double Arm Fiber Illumination Unit and C-FIR Ring
Fiber Illumination Unit use LEDs as the light
source. A label indicating photobiological safety is
attached to these illuminators in order to bring
attention to the following. (For details about the
label attachment position, see "Label Attached to
the Product" on page v.)
"Possibly hazardous optical radiation emitted from
this product. Do not stare at operating lamp.
May be harmful to the eyes.
RISK GROUP 2 IEC62471: 2006"
3 Be careful of the heat of the empty cube
Immediately after diascopic observation using an
epi-fluorescence attachment, the front face of the
empty cube may become hot, resulting in burns. Do
not touch the front face of the empty cube. Replace
the empty cube several minutes after diascopic
observation.
4 Caution on light leakage
Do not use the epi-fluorescence attachment while
the filter cube replacement cover is open. Harmful
light including ultraviolet light may leak and affect
fluorescence observation.
5 Anti-drop collar for the C-FMCN Focus Mount
When using a C-FMCN Focus Mount attached in
the middle of the support pillar, be sure to use the
anti-drop collar. Otherwise the zooming body may
slide down when the focus mount fixing screw is
loosened. This may result in injury such as pinching
fingers between the objective and sample, or
damage to the sample on the stage plate by the
objective.
6 C-FMCN Focus mount attachment orientation
Attach the C-FMCN focus mount to the stand so
that the focus mount faces the front of the stand.
If the focus mount is attached in the incorrect
orientation, the stand may fall over. This may result
in damage to the device or unexpected injury.
Safety Precautions
CAUTION
7 Specification of a light source
Be sure to use the specified light source for an
illuminator. Using a light source not specified can
cause malfunction and induce an accident. For the
specified light source, see Chapter 8, "2
Performance Properties" or the instruction manual
for the light source.
8 Avoid contact with water or chemical solutions.
Never expose this product to water or chemical
solutions, and avoid using this product in
circumstances where there is risk of exposure to
water or chemical solutions. Exposure of electric
parts (such as the HG Precentered Fiber
Illuminator) to liquids may cause a short circuit,
resulting in malfunction or abnormal heating. If
water or a chemical solution is splashed onto a
device, immediately turn off the power switch for
the device (press to the "O" position) and remove
the power cord from the receptacle. Then wipe off
moisture with a piece of dry cloth or something
similar. If water or a chemical solution enters this
product, stop using the product, and contact your
nearest Nikon representative.
9 Remove any covers from the system before
switching on.
Do not use the system while it is covered with a
piece of cloth, etc., Especially for a light source,
which is heated, the disturbance of heat release
may cause abnormal heat generation, causing
ignition or fire. Do not cover the system with a piece
of cloth or similar while in use.
10 Notes on routing cables
Connect and route the cables in accordance with
the specified methods. If the cables are not routed
and connected properly, the system may not
function correctly.
11 Do not place any object on top of the product.
Do not place any object on top of this product.
12 Cautions on assembling and installing the
product
● Take care to avoid pinching your fingers or
hands during system assembly and installation.
● Scratches or fingerprints, etc. on optical
components (such as lens and filters) will
degrade microscope images. Be careful to avoid
scratches or direct contact with the lens and
filters during system assembly.
x