Campbell Measurement and Control Module CR10 Operator's Manual page 251

CR10 INDEX
Tape Pointer (TPTR) 2-2
Tape recorder
Connecting to CR10 4-4
Data format for 4-5
Dump data (*8 Mode) 4-3
Interrupts during transfer 6-3
Manually initiated data transfer (*8 Mode) 4-3
On-line data transfer (Instruction 96) 4-1
TPTR (Tape Pointer) 2-2
Tapes, Recommended 4-4
Telecommunication 5-1
Automatic setting of baud rate 5-1
Automatic time-out from 5-2
Commands 5-3
Key definitions OV-10
Password 5-4
Remote keyboard OV-9, 5-4
Telecommunication states 5-4
with Binary responses C-1
Telecommunications Command OV-10
Telecommunications (Modem) Pointer (MPTR) 2-2
Temp (107) - [Instruction 11] 9-5
Temp, Module - [Instruction 17] 9-8
Temp RTD - [Instruction 16] 9-7
Temp TC SE - [Instruction 13] 9-6
Temp TC DIFF - [Instruction 14] 9-7
Temperature from Platinum R.T.D. -
[Instruction 16] 9-7
Programming examples 7-7, 7-8, 7-10
Temperature from thermocouples, See
Thermocouple temperature
Temperature of Module - [Instruction 17] 9-7
Programming example OV-13
Temperature range, CR10 14-1
Terminal emulator OV-9
Thermocoule Measurements 13-12
Thermocouple Temperature Measurement -
[Instruction 14] 9-7
Programming example 7-3
Single-Ended Voltage - [Instruction 13] 9-6
Technique/error analysis 13-13
Using an External Reference Junction 7-3
Three Wire Half Bridge - [Instruction 7] 9-4
Programming example 7-8
Throughput rate, Definition 1-1, A-3
Time - [Instruction 18] 9-8
Programming example 8-4
Time
Setting/displaying (*5 Mode) 1-2
Storing in Final Storage 11-4
Timer - [Instruction 26] 9-13
Timer, see SDM-INT8 8 Channel Interval
Tipping Bucket Rain Gage 7-6, 8-6
Totalize - [Instruction 72] 11-3
Programming example 8-3
I-8
TPTR 2-2
Tutorial OV-1
U
Use of Digital I/O Ports 14-7
User flags 3-3
Using the PC208 Terminal Emulator
(GraphTerm) OV-9
V
Vapor Pressure From Wet-/Dry-Bulb
Temperatures - [Instruction 57] 10-5
Programming example 12-3
Vehicle power supply 14-5
Vibrating wire, measure sensor, Geokon's 7-15
Vibrating Wire Measurement -
[Instruction 28] 9-13
Programming example 7-18
Voltage on analog input, excess vii
Voltage measurements
Differential 7-2
Differential/single-ended OV-3, 13-1
Integration 13-1
Ranges/codes and overrange detection 3-2, 9-1
Volts (SE) - [Instruction 1] 9-1
Volts (Diff) - [Instruction 2] 9-1
W
Watchdog reset 3-8
WDT-VP - [Instruction 57] 10-5
Wind Vector - [Instruction 69] 11-1
Programming example 8-8
Wiring Panel
Connecting to vehicle power supply 14-5
Description OV-1, 14-5
X
X * F - [Instruction 37] 10-2
Programming example 7-19
X * Y - [Instruction 36] 10-2
Programming example 7-22
X + F - [Instruction 34] 10-1
X + Y - [Instruction 33] 10-1
Programming example 7-19
X - Y - [Instruction 35] 10-1
X / (1-X), see Bridge Transform - [Instruction 59]
X / Y - [Instruction 38] 10-2
X Mod F - [Instruction 46] 10-3
Y
X - [Instruction 47] 10-3