Campbell Measurement and Control Module CR10 Operator's Manual page 245

CR10 INDEX
Effect of lead length on signal settling
time 13-3
Tipping bucket rain gage with long leads 7-6
Calibration - [Instruction 24] 9-12
Process 13-22
Cassette recorder 4-4
Cautionary notes vii
CD16, see SDM-CD16 Control Port Expansion
Module
Channels
Differential analog OV-3, 13-2
Single-ended analog OV-3, 13-2
Checksum 5-2
Clock
Example of setting OV-17
Set/display time (*5 Mode) 1-2
CM6/CM10 Tripods grounding protection 14-6
Common mode range 13-3, 14-7
Communicating with the CR10 OV-8
Via telemetry 5-1
With external peripherals 4-1
Communication
Protocol OV-8, 6-7, 5-2
Troubleshooting 6-7
Compiling
Data 1-4
Errors 3-9
Program 1-2
Computation of Running Average 8-1
Computer
Connecting to serial port OV-9
Save/load program (*D Mode) 1-9
Use with SC32A OV-9, 6-5
Connecting Power to the CR10 OV-3, OV-5
Control Port Expansion Module with Drivers,
see SDM-CD16
Control/logic ports
Command codes affecting OV-3, 12-1
Configuration, see Port Set - [Instruction 20]
Definition OV-4
Display/toggle [Instruction 20] 1-4, 9-8, C-1
Indexing 3-1
Voltages > 5.5, Applying vii
Cosine 10-3
Counter
Pulse Count - [Instruction 3] 9-1
Setting to 16 bit accumulator 9-2
CR10 Pin Port description D-1
CR10KD Keyboard Display and SC12 cable OV-9
Displaying Stored Data (*7 Mode) 2-3
Entering programs with OV-12
Key Definition OV-10
Typical Current Drain 14-1
Wiring Panel
Connecting to vehicle power supply 14-5
I-2
Description OV-1, 14-7
D
Data point
Definition A-1
Number per Output Array 4-6
Data retrieval, External storage peripherals
General 4-1
Hardware options OV-17
Manually initiated (*8 Mode) 4-3
Methods and related instructions OV-18
On-line (Instruction 96) 4-1, 12-6
Print device 4-2
Print formats 4-5
Site Visitations, Estimating time between 4-3
Storage Module 4-6
Tape recorder 4-3
Data Set Ready (DSR) 6-6
Data Storage Pointer (DSP) 2-1, 4-2
Data Terminal Equipment (DTE) pin configuration 6-6
Data transfer
ASCII vs. binary 5-1
Interrupts During 6-3
Manual (*8 Mode) 4-3
On-line (Instruction 96) 4-1, 12-6
Data transmission, See Data retrieval
Data types parameter 3-1
Dataloggers, Differences between CR10 and
other OV-1
Date (*5 Mode), Setting/displaying 1-2
DC103A/DC112 Phone Modem current drain,
typical 14-1
Desiccant
in Enclosure 14-9
Replacement in CR10 14-1
Differential measurements on analog inputs
OV-4, 13-2
Differential Voltage w/ Excitation & Delay -
[Instruction 8] 9-1
Differential Volts - [Instruction 2] 9-2
Programming example 7-2
Direct battery connection 14-5
Display Pointer (DPTR) 2-2
Display, See CR10KD Keyboard/Display
Displaying/Altering Input Memory, Flags and
Ports-*6 Mode 1-3
Divide
X/Y - [Instruction 38] 10-2
X Mod F - [Instruction 46] 10-3
DO - [Instruction 86] 12-2
Programming example OV-13
DPTR 2-2
Druck PDCR 930 depth pressure transducer
Programming example 7-10