Campbell Measurement and Control Module CR10 Operator's Manual page 244

* Modes, See Modes
1/X - [Instruction 42] 10-2
107 Thermistor Probe - [Instruction 11] 9-5
Programming examples 7-3
CR10TCR Thermocouple Reference 7-3
12V terminals OV-3, OV-4
100 ohm PRT
3 wire half bridge 7-8
4 wire half bridge 7-6
4 wire full bridge 7-9
207 Relative Humidity Probe - [Instruction 12] 9-6
Programming example 7-4
227 Gypsum Soil Moisture Block 7-13
3 Wire Half Bridge - [Instruction 7] 9-4, 13-18,
13-19, 13-20
Example 7-8
4 Wire Full Bridge - [Instruction 6] 9-4, 13-18,
13-19, 13-20
Example 7-9
5th Order Polynomial - [Instruction 55] 10-5
Programming examples 7-14, 7-15
5V outputs OV-3, OV-4, 14-5
A
A*X + B, see Scaling Array with Multiplier and
Offset - [Instruction 53]
A04 Analog Output, see SDM-A04
A6Rel-12/A21Rel-12 Relay Driver 14-7
ABS(X) - [Instruction 43] 10-3
AC Half Bridge - [Instruction 5] 9-3
Programming examples 7-14, 8-4
Activate Serial Data Output - [Instruction 96]
4-1, 12-6
Interrupts during 6-3
Programming examples OV-17
Using Storage Module with 4-7
Alkaline power supply 14-2
AM416 Multiplexer
Measuring soil moisture blocks 8-3
Using control ports and loop 8-3
Analog ground definition OV-3, OV-4
Analog inputs OV-3, OV-4
Analog output, see SDM-A04
Analog to Digital (A/D) conversion 13-1
AND construction, Logical 3-5
Anemometer (Photochopper output)
Programming example 7-5
Array ID
and Output Interval A-2
Calculating data points 4-6
CR10 INDEX
Definition A-2
Setting ID 2-1, 11-5
ASCII
Characters E-1
Definition A-1
Output formats 4-6
Program transfer to computer/printer 1-8
Table E-1
Terminal or computer with terminal emulator OV-9
Table E-1
Transmission 6-7
Asynchronous, Definition A-1
Automatic calibration sequence 13-22
Average - [Instruction 71] 11-3
Programming example OV-16
Average, Computing running 8-1
AVW1/AVW4 Vibrating Wire Interface 7-15
B
Battery Power 14-2
Battery Voltage - [Instruction 10] 9-5
Baud rate
Definition 6-7, A-1
Begin Case Statement - [Instruction 93] 12-5
Binary telecommunications C-1
Generation of signature C-4
Block Move - [Instruction 54] 10-4
Programming example 8-1
Bridge measurements 13-17
3 Wire Half Bridge 100 ohm PRT 7-8
4 Wire Full Bridge (Pressure Transducer)
7-10
4 Wire Full Bridge 100 ohm PRT 7-9
4 Wire Half Bridge 100 ohm PRT 7-6
6 Wire Full Bridge (Lysimeter) 7-11
Comparison of bridge measurement
instructions 13-18
Diagram of bridge measuring circuits 13-18
with AC excitation 13-19
Bridge Transform - [Instruction 59] 10-6
Programming examples 7-10, 7-14, 8-4
Burst Measurement - [Instruction 23] 9-9
C
C20 Cassette Interface 4-3
Cables/Leads
Avoid PVC insulated conductors 13-10
Connecting Leads to Wiring Panel OV-1
I-1