Campbell Measurement and Control Module CR10 Operator's Manual page 118

converts the readings to engineering units.
Temperature (°C), pressure (psi), and signature
are stored in Locations 17, 18, and 19,
respectively. Instructions to output the readings
to Final Storage are not included in this
example.
* 1 Table 1 Programs
01: 60 Sec. Execution Interval
If the program has just compiled, a 0 is in Loc
20. If Loc 20 = 0, call subroutine 1 and load the
temperature coefficients into Loc 3..16.
01: P89 If X<=>F
01: 20 X Loc COMP CHK
02: 1 =
03: 0 F
04: 1 Call Subroutine 1
Measure temperature period in microseconds
02: P27 Period Average (SE)
01: 1 Rep
02: 4 Input gain=1
03: 12 IN Chan
04: 9000 No. of Cycles
05: 6 Time Out (units=.01sec)
06: 1 Loc [:TEMP,us]
07: 1 Mult
08: 1 Offset
Measure pressure period in microseconds
03: P27 Period Average (SE)
01: 1 Rep
02: 4 Input gain=1
03: 1 IN Chan
04: 5000 No. of Cycles
05: 15 Time Out (units=.01sec)
06: 2 Loc [:PRESS,us]
07: 1 Mult
08: 0 Offset
04: P64 Paro Processing
01: 1 Start Loc: Temp(us),
Pressure(us), U
02: 17 Start Loc: Temp(°C),
Pressure(psi), SIG
05: P End Table 1
* 3 Table 3 Subroutines
01: P85 Beginning of Subroutine
01: 1 Subroutine Number
SECTION 7. MEASUREMENT PROGRAMMING EXAMPLES
02:
01:
02:
03:
03:
01: -3970.3
02:
03:
04:
01: -7114.3
02:
03:
05:
01:
02:
03:
06:
01:
02:
03:
07:
01:
02:
03:
08:
01:
02:
03:
09:
01:
02:
03:
10:
01:
02:
..T
03:
0 5
11:
01:
02:
03:
12:
01:
02:
03:
P30 Z=F
5.8603 F
0 Exponent of 10
3 Z Loc [:U0 ]
P30 Z=F
F
0 Exponent of 10
4 Z Loc [:Y1 ]
P30 Z=F
F
0 Exponent of 10
5 Z Loc [:Y2 ]
P30 Z=F
102.78 F
0 Exponent of 10
6 Z Loc [:Y3 ]
P30 Z=F
70.294 F
0 Exponent of 10
7 Z Loc [:C1 ]
P30 Z=F
6.6101 F
0 Exponent of 10
8 Z Loc [:C2 ]
P30 Z=F
-119.29 F
0 Exponent of 10
9 Z Loc [:C3 ]
P30 Z=F
30.884 F
0 Exponent of 10
10 Z Loc [:D1 ]
P30 Z=F
0 F
0 Exponent of 10
11 Z Loc [:D2 ]
P30 Z=F
26.337 F
0 Exponent of 10
12 Z Loc [:T1 ]
P30 Z=F
.85170 F
0 Exponent of 10
13 Z Loc [:T2 ]
7-25