Campbell Measurement and Control Module CR10 Operator's Manual page 250

SC90 Serial Line Monitor 4-7
SC92/93 for writing to tape, Don't use 4-4
SC92A/93A 4-4
Scaling Array with Multiplier & Offset -
[Instruction 53] 10-4
Programming example 8-7
SDC99 Synchronous Device Interface 6-3
SDM-A04 4 Channel Analog Output Module -
[Instruction 103] 9-15
Current drain, Typical 14-1
Programming example 8-7
SDM-CD16 Control Port Expansion Module -
[Instruction 104] 9-15
Current drain, Typical 14-1
SDM-INT8 8 Channel Interval Timer -
[Instruction 101] 9-14
Current drain, Typical 14-1
SDM-SW8A Switch Closure Input Module -
[Instruction 102] 9-14
Current drain, Typical 14-1
SD's, see Synchronous devices
SDM peripherals 7-24
Security 1-7
Send Character - [Instruction 98] 12-8
Sensors
Connecting to Wiring Panel OV-3
Effect of lead length on signal
settling time 13-3
Settling errors for CSI resistive sensors 13-8
Serial Input/Output
General 6-1
Pin Description 6-1
Serial Out - [Instruction 96] 4-1, 12-6
Programming example OV-17
Set Active Storage Area - [Instruction 80] 11-5
Programming examples 8-2, 8-3, 8-9
Set Resolution Data Storage Format -
[Instruction 78] 11-5
Setting and Displaying the Clock - *5 Mode 1-2
Spark gaps on wiring panel terminals 14-6
Signature
CR10 PROM 1-6, B-1
Definition A-3
Generation of C-4
Signature - [Instruction 19] 9-8
Sin(X) - [Instruction 48] 10-3
Single-ended measurements on analog inputs
OV-3, 13-1
Single-ended Volts - [Instruction 1] 9-1
Programming example 7-1
SM192/716 Storage Modules, see Storage
Modules
Sample on Maximum or Minimum -
[Instruction 79] 11-5
Solar panels, Solarex MSX10/MSX18 14-5
Spatial Average - [Instruction 51] 10-4
Spatial Maximum - [Instruction 49] 10-3
Spatial Minimum - [Instruction 50] 10-4
Specifications OV-20
SPTR, see Storage Module Pointer
Square Root - [Instruction 39] 10-2
Standard and Weighted Value Histogram -
[Instruction 75] 11-3
Standard Deviation in Time -
[Instruction 82] 11-5
Step Loop Index - [Instruction 90] 12-4
Stop Bit 6-7
Storage and retrieval options, Data OV-19
Storage Module Pointer (SPTR) 2-2
Storage Modules (SM192/716) 4-7
Addressing with CR10 4-1
Commands to (*9 Mode) 4-8
Current drain, Typical 14-2
File Mark 4-7
Manually initiated data output (*8 Mode) 4-7
Save/load program (*D Mode) 1-9
Use with Instruction 96 4-2
Storage peripherals, External 4-1
Storage
See Final Storage, input storage,
intermediate storage
Store Area - [Instruction 80] 11-5
Programming example 8-3
Strip charts
Converting wind direction output
to 0-540 8-8
Use with SDM-A04 8-7
Subroutines
Entering 1-1
Label Subroutine - [Instruction 85] 12-1
Port Interrupt Subroutines 12-1
Programming Example 8-6
Subtract - [Instruction 35] 10-1
SW8A Switch Closure Input Module, see
SDM-SW8A
Switch closure
Counting on Tipping Bucket
Rain Gage 8-6
Measuring 9-1
Switch Closure Input Module, see SDM-SW8A
Switching power to a device 14-7
Synchronous Device Communication 6-4
Synchronous, Definition A-3
System memory OV-5, 1-4
System status (*B Mode) 1-6
T
Tables, List of LT-1
see also Program Tables
CR10 INDEX
I-7