Pilz PSEN ml s 1.1 Operating Manual
  1. Manuals
  2. Brands
  3. Pilz Manuals
  4. Security Sensors
  5. PSEN ml s 1.1
  6. Operating manual
Pilz PSEN ml s 1.1 Operating Manual

Pilz PSEN ml s 1.1 Operating Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

PSEN ml s 1.1/2.1/2.2
}
PSEN sensor technology
Operating Manual-1004710-EN-05

Advertisement

Table of Contents
loading

Related Manuals for Pilz PSEN ml s 1.1

Summary of Contents for Pilz PSEN ml s 1.1

  • Page 1 PSEN ml s 1.1/2.1/2.2 PSEN sensor technology Operating Manual-1004710-EN-05...
  • Page 2 Preface This document is the original document. All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made for the user's internal purposes. Suggestions and comments for improving this documenta- tion will be gratefully received.

  • Page 3: Table Of Contents

    EMC requirements ........................Connection to control systems and evaluation devices ............ Important information........................ Minimum requirements for activation of guard locking ............. Single connection ........................Series connection ........................Connection to Pilz evaluation devices ..................Operating Manual PSEN ml s 1.1/2.1/2.2 1004710-EN-05...
  • Page 4 Radio approval.......................... 16.2 Technical details for mounting bracket without handle unit ............16.3 Technical details for mounting bracket with handle unit ............16.4 Technical details for escape release 570460 - 570462, 570470 ..........Operating Manual PSEN ml s 1.1/2.1/2.2 1004710-EN-05...
  • Page 5 Technical details escape release 570471-570473 ..............16.8 Technical details escape release 570474-570475 ..............16.9 Technical details for auxiliary release 570461................Order reference ........................17.1 System ............................17.2 Accessories ..........................Appendix ..........................EC declaration of conformity ....................Operating Manual PSEN ml s 1.1/2.1/2.2 1004710-EN-05...

  • Page 6: Introduction

    This operating manual explains the function and operation, describes the installation and provides guidelines on how to connect the product. This documentation is valid for the product PSEN ml s 1.1/2.1/2.2 from Version 2.0. Using the documentation This document is intended for instruction. Only install and commission the product if you have read and understood this document.
  • Page 7 Introduction INFORMATION This gives advice on applications and provides information on special fea- tures. Operating Manual PSEN ml s 1.1/2.1/2.2 1004710-EN-05...

  • Page 8: Safety

    – EN ISO 13849-1: PL e (Cat. 4 ) EN ISO 14119 – Coding level with actuator PSEN ml s 1.1: low, type 4 – Coding level with actuator PSEN ml s 2.1/2.2: high, type 4 The safety switch may only be used with one of the approved actuators (see...

  • Page 9: Safety Regulations

    Are familiar with the basic regulations concerning health and safety / accident prevention, Have read and understood the information provided in the section entitled Safety Have a good knowledge of the generic and specialist standards applicable to the specific application. Operating Manual PSEN ml s 1.1/2.1/2.2 1004710-EN-05...

  • Page 10: Warranty And Liability

    – Keep the substitute actuator in a safe place and protect it from unau- thorised access. – Install substitute actuators as described in Installation [ 38]. – Destroy any used actuators before disposal. Operating Manual PSEN ml s 1.1/2.1/2.2 | 10 1004710-EN-05...

  • Page 11: Overview

    Auxiliary release for opening the safety gate 1 signal output Suitable for left and right hinged safety gates Pilz coding type – PSEN ml s 1.1: coded – PSEN ml s 2.1: fully coded – PSEN ml s 2.2: uniquely coded M12, 12-pin male connector Operating Manual PSEN ml s 1.1/2.1/2.2...
  • Page 12 Order reference: Accessories [ 83]). The actuator is available in two types (see Order reference: Accessories [ 83]). – Standard actuator – Actuator with rounded tip Standard actuator Actuator with rounded tip Operating Manual PSEN ml s 1.1/2.1/2.2 | 12 1004710-EN-05...

  • Page 13: Function Description

    A switch to a high signal will only lead to normal safety switch operation if both inputs had a low signal. From this moment on, the switch to high may occur (partial operation lock see Error display [ 63]). Operating Manual PSEN ml s 1.1/2.1/2.2 | 13 1004710-EN-05...

  • Page 14: Activation Of Safety Inputs S31 And S41 (Solenoid Operation)

    Pulse duration Lock/Unlock Request in ms the series connection 1050 1400 1750 2100 After activation, the inputs must be low. Another pulse of the specified duration at these in- puts deactivates guard locking. Operating Manual PSEN ml s 1.1/2.1/2.2 | 14 1004710-EN-05...
  • Page 15 Series connection of diagnostics with Safety Device Diagnostics 1. PSEN ml 2. PSEN ml Fieldbus module Series connection of the solenoid operation 1. PSEN ml 2. PSEN ml S31 S41 42 S31 S41 32 Operating Manual PSEN ml s 1.1/2.1/2.2 | 15 1004710-EN-05...

  • Page 16: Activation With Specification Of Direction

    Maximum time between the rising edges from S31 and S42 4.2.2 Activation without specification of direction The guard locking changes its state when the time between the rising edges from S31 and S41 < 20 ms. Operating Manual PSEN ml s 1.1/2.1/2.2 | 16 1004710-EN-05...

  • Page 17: Safety Device Diagnostics

    83]) to connect several sensors with only one cable from the field in the control cabinet. Further information on Safety Device Diagnostics can be found in Additional documents that apply [ Operating Manual PSEN ml s 1.1/2.1/2.2 | 17 1004710-EN-05...

  • Page 18: Operating Modes

    S31 and S41 are activated simultaneously. – Force direction: The safety switch is selectively activated or deactivated by offset ac- tivation of the rising edges at S31 and S41. Operating Manual PSEN ml s 1.1/2.1/2.2 | 18 1004710-EN-05...
  • Page 19 [8] Outputs will be deactivated [9] Guard locking will be deactivated [10] Gate is open [t1] Processing time of guard locking signal = 100 ms [t2] Time window for changing guard locking status Operating Manual PSEN ml s 1.1/2.1/2.2 | 19 1004710-EN-05...
  • Page 20 [8] Outputs will be deactivated [9] Guard locking will be deactivated [10] Gate is open [t1] Processing time of guard locking signal = 100 ms [t2] Time window for changing guard locking status Operating Manual PSEN ml s 1.1/2.1/2.2 | 20 1004710-EN-05...

  • Page 21: Block Diagram

    Function description Block diagram Power & Device & Lock Lock Sensor 1 & Magnet Lock Sensor 2 & & Signal Diagnostic Output Safety Gate Receiver Actuator Operating Manual PSEN ml s 1.1/2.1/2.2 | 21 1004710-EN-05...

  • Page 22: Auxiliary Release

    61]) and the safety switch switches to a fault condition. It is possible to open guard locking using the control system. Legend [1] Auxiliary release screw Torx T10 [2] Security screw Torx T10, sealed with varnish when delivered Operating Manual PSEN ml s 1.1/2.1/2.2 | 22 1004710-EN-05...

  • Page 23: Recommissioning

    As a result the actuator cannot engage with the safety switch, guard locking is not activated and the machine is prevented from starting. Legend [1] Through hole on the actuator for attaching a padlock [2] Padlock [3] Actuator Operating Manual PSEN ml s 1.1/2.1/2.2 | 23 1004710-EN-05...

  • Page 24: Escape Release Accessory

    EN ISO 14119. Legend [1] Escape release stationary [2] Escape release externally [3] Tension pressure cables in lengths of 0.50 m to 4 m [4] Button of the escape release pin [5] Escape release pin Operating Manual PSEN ml s 1.1/2.1/2.2 | 24 1004710-EN-05...

  • Page 25: Recommissioning

    1. Reset the handle. 2. Switch the voltage off and then on again. 3. Carry out a function test using the escape release. The safety function may only be checked by qualified personnel. Operating Manual PSEN ml s 1.1/2.1/2.2 | 25 1004710-EN-05...

  • Page 26: Wiring

    Safety output channel 1 Green Operation of solenoid to Pink open and close guard lock- ing (channel 1) Safety output channel 2 Yellow Safety input channel 1 Black Signal output/diagnostic Grey output Diagnostics input Operating Manual PSEN ml s 1.1/2.1/2.2 | 26 1004710-EN-05...

  • Page 27: Emc Requirements

    Only use safety relays with a 24 VDC supply voltage. Safety relays with a wide-range power supply or in AC device versions have internal potential isolation and are not suitable as evaluation devices. Operating Manual PSEN ml s 1.1/2.1/2.2 | 27 1004710-EN-05...

  • Page 28: Connection To Control Systems And Evaluation Devices

    – Use an evaluation device/safety system to test whether the plant is in a safe condition. – Do not operate the solenoid via S31/S41 unless the plant is in a safe condition. Operating Manual PSEN ml s 1.1/2.1/2.2 | 28 1004710-EN-05...

  • Page 29: Minimum Requirements For Activation Of Guard Locking

    Monitoring of shorts across signal cables through activation of guard locking 24 V S11 S21 Safety control system PSEN ml PSEN ml Activation of guard locking actuator safety switch Lock/Unlock Request 2 Lock/Unlock Request 1 Operating Manual PSEN ml s 1.1/2.1/2.2 | 29 1004710-EN-05...
  • Page 30 24 V S11 S21 Safety control system PSEN ml PSEN ml Activation of guard locking actuator safety switch 24 V Lock/Unlock Request 2 Lock/Unlock Request 1 Legend [1] Protected cable layout Operating Manual PSEN ml s 1.1/2.1/2.2 | 30 1004710-EN-05...

  • Page 31: Single Connection

    Lock/Unlock Request Single connection Safety switch 24 V 0 V Actuator 24 V I1 (FS) I2 (FS) O2 (FS) O1 (FS) Programmable safety system Activation of guard locking FS: Failsafe Operating Manual PSEN ml s 1.1/2.1/2.2 | 31 1004710-EN-05...

  • Page 32: Series Connection

    Determine the values under the following conditions: Room temperature (25°C), conductor cross section 0.25 mm , output load per output (12, 22, Y32) each ≤ 10mA Legend [1] Safety control system [2] Safety switch PSEN ml Operating Manual PSEN ml s 1.1/2.1/2.2 | 32 1004710-EN-05...
  • Page 33 50 m 30 m 180 m 50 m 50 m 30 m 30 m 20 m 180 m 50 m 50 m 20 m 20 m 20 m 20 m 180 m Operating Manual PSEN ml s 1.1/2.1/2.2 | 33 1004710-EN-05...
  • Page 34 Connection to control systems and evaluation devices 24 V 0 V Safety switch Actuator Safety switch Actuator Actuator Safety switch Safety control system FS: Failsafe Fieldbus module Operating Manual PSEN ml s 1.1/2.1/2.2 | 34 1004710-EN-05...

  • Page 35: Connection To Pilz Evaluation Devices

    – Connect the 12-core cables of the safety switch to the terminal block of the control cabinet. Connection to Pilz evaluation devices The safety switch can be connected to Pilz evaluation devices. Suitable Pilz evaluation devices are, for example: PNOZmulti for safety gate monitoring Configure the switch in the PNOZmulti Configurator with switch type 3.
  • Page 36 Connection to PNOZmulti is illustrated by way of example. Connection example with PNOZmulti and Safety Device Diagnostics Activation of guard locking via SDD ES module PSEN ml PNOZmulti O2 (FS) O1 (FS) following PSEN ml Operating Manual PSEN ml s 1.1/2.1/2.2 | 36 1004710-EN-05...

  • Page 37: Teaching In The Actuator

    Technical details [ 73]) is taught in automatically as soon as it is brought into the response range. NOTICE No other actuator may be taught in once this actuator has been taught. Operating Manual PSEN ml s 1.1/2.1/2.2 | 37 1004710-EN-05...

  • Page 38: Installation

    – On the actuator: By complying with the max. torque setting (see Technical details [ 73]) and medium-strength threadlockers. Pilz recommends that you use the PSEN ml actuator center ring (see Order reference [ 83]) only with small door radiuses (see...

  • Page 39: Installation Types

    [ side-on to actuator [ on the gate frame. 2. Use two M5 screws to fix the actuator to the gate. Operating Manual PSEN ml s 1.1/2.1/2.2 | 39 1004710-EN-05...

  • Page 40: Installation On Swing Gate

    Install the safety switch horizontally at a swing gate Depending on the installation boundary conditions, a larger gate radius may be required (see diagram). Please contact Pilz when smaller gate radiuses are required. Operating Manual PSEN ml s 1.1/2.1/2.2 | 40...
  • Page 41 α Tilt angle when installing the actuator Tilt the actuator by 10° when installing, when the door radius is R < 600 mm. Pilz recommends that you use the PSEN ml actuator 10° adapter for correctly installing the actuator. Operating Manual PSEN ml s 1.1/2.1/2.2...

  • Page 42: Installation Safety Switch

    Fixing screws crosswise to actuator with L- Tapped holes for two M6 screws on the bracket mounting surface, for attaching the mount- ing surface Operating Manual PSEN ml s 1.1/2.1/2.2 | 42 1004710-EN-05...

  • Page 43: Installation Without Mounting Plate

    Provide the mounting surface with tapped holes as indicated. ø 8,5 1. Attach the mounting plate to the swing gate/sliding gate. 2. Use four M5 screws to fix the safety switch to the mounting plate. Operating Manual PSEN ml s 1.1/2.1/2.2 | 43 1004710-EN-05...

  • Page 44: Installation Using L-Brackets

    1. Use two M6 screws to fix the mounting bracket to the gate. The position of the drill holes can be taken from the section entitled Dimensions. 2. Use four M5 screws to fix the safety switch to the mounting bracket. Operating Manual PSEN ml s 1.1/2.1/2.2 | 44 1004710-EN-05...

  • Page 45: Actuator Installation

    1. Use two M6 screws to fix the mounting bracket to the gate. The position of the drill holes can be taken from the section entitled Dimensions. 2. Use two M5 screws to fix the actuator to the mounting bracket. Fig.: Actuator, installed on mounting bracket Operating Manual PSEN ml s 1.1/2.1/2.2 | 45 1004710-EN-05...

  • Page 46: Install Fixing Screws Side-On To Actuator

    Technical details [ 73]. Fig.: Fixing screws of the safety switch in parallel to actuator Legend [1] Safety switch [2] Actuator [3] Fixing screws of the safety switch in parallel to actuator Operating Manual PSEN ml s 1.1/2.1/2.2 | 46 1004710-EN-05...

  • Page 47: Centre The Bolt In The Actuator Housing

    After 50.000 cycles it may happen that the actuator misaligns, and that it has to be realigned regularly. Bolt centred within the actu- Bolt not centred within the actuator Bolt with PSEN ml actuator center ator housing housing ring in the actuator housing Operating Manual PSEN ml s 1.1/2.1/2.2 | 47 1004710-EN-05...

  • Page 48: Rotate The Bolt In The Actuator Housing 90

    2. Rotate the bolt in the housing skin by 90° in the required direction ([2]). Legend [1] Spring plate in the housing skin [2] Bolt, can be rotated 90° [3] Housing skin 3. Centre the bolt in the actuator housing [ 47]. Operating Manual PSEN ml s 1.1/2.1/2.2 | 48 1004710-EN-05...

  • Page 49: Escape Release

    Ensure that these versions are installed as straight as possible. The mounting surface has to completely cover the bottom of the escape release housing. The bottom of the escape release housing must not be accessible after installation. Operating Manual PSEN ml s 1.1/2.1/2.2 | 49 1004710-EN-05...

  • Page 50: Installation Positions For Escape Release

    Installation positions for escape release The stationary escape release can be installed on the three auxiliary releases in three dif- ferent directions each. Legend Installation options at the sides Installation options at the back Operating Manual PSEN ml s 1.1/2.1/2.2 | 50 1004710-EN-05...
  • Page 51 The external escape release can be installed on the three auxiliary releases in four different directions each. The push/pull cable can be led out on different sides. Legend Installation options at the sides Installation options at the back Operating Manual PSEN ml s 1.1/2.1/2.2 | 51 1004710-EN-05...

  • Page 52: Installation Stationary Escape Release

    To bridge larger distances the escape release pin can be extended by a max. of 25 mm two times (see Order reference: Accessories [ 83]). Operating Manual PSEN ml s 1.1/2.1/2.2 | 52 1004710-EN-05...
  • Page 53 Installation Legend [1] Button of the escape release pin [2] Escape release pin Operating Manual PSEN ml s 1.1/2.1/2.2 | 53 1004710-EN-05...

  • Page 54: Installation External Escape Release

    [2] Pin in the adapter disk [3] Hexagon sockets M3x8 3. Screw the escape release with the four raised head screws M3x12 to the adapter disk with 1,2 - 1,5 Nm (see diagram). Operating Manual PSEN ml s 1.1/2.1/2.2 | 54 1004710-EN-05...
  • Page 55 Screw the housing of the escape release with the screws [1] to a mounting surface with 6 - 6,5 Nm (see diagram). Legend [1] Screwing the escape release to the mounting area [2] Screwing the cable Operating Manual PSEN ml s 1.1/2.1/2.2 | 55 1004710-EN-05...
  • Page 56 Installation Fastening for the escape release (order no. 570463) The escape release is fastened using a bracket (not in the Pilz portfolio). The bracket must have the following properties: Corrosion-resistant material Material thickness: 4 +/- 0.5 mm Only low elastic deformation may occur at a force of 150 N. The cable must be able to move with it.

  • Page 57: Dismantling Of Escape Release (Order No. 570466 - 570 475)

    6. Push the cable with the fork head [3] on the fork in the escape release. The slot nut [4] must be fitted into the nut again. 7. Tighten the nut [2] with 6 - 6,5 Nm. 8. Put the lid [1] back on. Operating Manual PSEN ml s 1.1/2.1/2.2 | 57 1004710-EN-05...

  • Page 58: Auxiliary Release

    Max. torque setting: 1 Nm Deactivated To activate the auxiliary release the button handle must be unscrewed and then screwed back on to the piston rod rotated 180°. Activated Operating Manual PSEN ml s 1.1/2.1/2.2 | 58 1004710-EN-05...

  • Page 59: Adjustment

    M5 screw for an M5 locking screw. 3. Tighten up the M5 screw or M5 locking screw. Please note the max. torque setting stated in the Technical details [ 73]. Operating Manual PSEN ml s 1.1/2.1/2.2 | 59 1004710-EN-05...

  • Page 60: Operation

    S11 and S21 are low Green Safety gate open, actuator not de- tected, guard locking deactivated, safety inputs S11 and S21 are high Green Yel- Operating Manual PSEN ml s 1.1/2.1/2.2 | 60 1004710-EN-05...
  • Page 61 If safety inputs voltage Yellow Yel- S31 and S41 are activated or de- activated while an undervoltage warning is present, the safety switch switches to a fault condition. Operating Manual PSEN ml s 1.1/2.1/2.2 | 61 1004710-EN-05...
  • Page 62 One input is low, This will cancel Yel- Green after both inputs the lock. were high Display not defin- Partial operation itive lock: Both inputs are Yel- Green high Operating Manual PSEN ml s 1.1/2.1/2.2 | 62 1004710-EN-05...

  • Page 63: Error Display

    Display not definitive Safety switch Change the safety switch. does not start Display not Wrong actuator Use only approved combinations Dis- definitive (see Approved play combinations [ 11]) Green Yellow defin- itive Operating Manual PSEN ml s 1.1/2.1/2.2 | 63 1004710-EN-05...

  • Page 64: Checks And Maintenance

    If one of these conditions is not met, the signal at the safety outputs will be low. Escape release Test whether the button of the escape release pin can be detected and reached. Check the function of the escape release. Operating Manual PSEN ml s 1.1/2.1/2.2 | 64 1004710-EN-05...

  • Page 65: Dimensions

    Dimensions Dimensions Actuator without center ring, rear view PSEN ml 1.1/PSEN ml 2.1 actuator 61,7 PSEN ml 1.1/PSEN ml 2.1 round ac- tuator Safety switch Actuator Operating Manual PSEN ml s 1.1/2.1/2.2 | 65 1004710-EN-05...
  • Page 66 Dimensions Mounting plate (see Accessories [ 83]) Fig.: Order no.: 570 490 Operating Manual PSEN ml s 1.1/2.1/2.2 | 66 1004710-EN-05...
  • Page 67 Dimensions Mounting bracket for sliding gate (see Accessories [ 83]) Fig.: Order no.: 570 492 Operating Manual PSEN ml s 1.1/2.1/2.2 | 67 1004710-EN-05...
  • Page 68 Dimensions Mounting bracket for swing gate (see Accessories [ 83]) 15,5 69,5 89,5 Fig.: Order no.: 570 493 15,5 89,5 69,5 Fig.: Order no.: 570 494 Operating Manual PSEN ml s 1.1/2.1/2.2 | 68 1004710-EN-05...
  • Page 69 Dimensions Mounting bracket with handle unit for sliding gate (see Accessories [ 83]) Fig.: Order no.: 570 495 Operating Manual PSEN ml s 1.1/2.1/2.2 | 69 1004710-EN-05...
  • Page 70 Dimensions Mounting bracket with handle unit for swing gate (see Accessories [ 83]) 69,5 Fig.: Order no.: 570 496 Operating Manual PSEN ml s 1.1/2.1/2.2 | 70 1004710-EN-05...
  • Page 71 Dimensions 79,5 Fig.: Order no.: 570 497 Operating Manual PSEN ml s 1.1/2.1/2.2 | 71 1004710-EN-05...
  • Page 72 Dimensions L-bracket for the safety switch (see Accessories [ 83]) 19,2 193,5 217,2 178,8 Fig.: Order no.: 570 476 Distance between safety switch mounting surface and actuator mounting surface 69,5 Operating Manual PSEN ml s 1.1/2.1/2.2 | 72 1004710-EN-05...

  • Page 73: Technical Details

    24 V DC 24 V DC Current at solenoid input 500 mA 500 mA 500 mA Input current range 1,6 - 3 mA 1,6 - 3 mA 1,6 - 3 mA Operating Manual PSEN ml s 1.1/2.1/2.2 | 73 1004710-EN-05...
  • Page 74 100 ms 100 ms 100 ms Environmental data 570406 570408 570410 Temperature of metal sur- face at ambient temperat- ure: 25 °C 40 °C 40 °C 40 °C Operating Manual PSEN ml s 1.1/2.1/2.2 | 74 1004710-EN-05...
  • Page 75 Cable diameter K1 6,5 mm 6,5 mm 6,5 mm Escape release available No Mechanical life 1,000,000 cycles 1,000,000 cycles 1,000,000 cycles Mechanical life with cen- tering ring 50,000 cycles 50,000 cycles 50,000 cycles Operating Manual PSEN ml s 1.1/2.1/2.2 | 75 1004710-EN-05...
  • Page 76 Min. gate radius 300 mm 300 mm 300 mm Dimensions Height 217,2 mm 217,2 mm 217,2 mm Width 40 mm 40 mm 40 mm Depth 40 mm 40 mm 40 mm Operating Manual PSEN ml s 1.1/2.1/2.2 | 76 1004710-EN-05...
  • Page 77 950 g 950 g 950 g Weight of actuator 145 g 145 g 145 g Weight 1.100 g 1.100 g 1.100 g Where standards are undated, the 2015-11 latest editions shall apply. Operating Manual PSEN ml s 1.1/2.1/2.2 | 77 1004710-EN-05...

  • Page 78: Classification According To Zvei, Cb24I

    1,5 nF Safe 1-pole HL outputs Source Drain Safety switch Evaluation device C1, C2 Source parameters Min. Typ. Max. Test impulse duration 450 µs Rated current 0,1 A Capacitive load 70 nF Operating Manual PSEN ml s 1.1/2.1/2.2 | 78 1004710-EN-05...

  • Page 79: Safety Characteristic Data

    PAScal software tool to calculate the safety function's SIL/PL values. NOTICE Be sure that you observe the mechanical life. The safety characteristic data are only valid as long as the values of mechanical life are met. Operating Manual PSEN ml s 1.1/2.1/2.2 | 79 1004710-EN-05...

  • Page 80: Supplementary Data

    2) this product must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this product not expressly approved by Pilz may void the FCC authorization to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

  • Page 81: Technical Details For Escape Release 570460 - 570462, 570470

    80 N 80 N 80 N 80 N Service life escape release 6050 cycles 6050 cycles 6050 cycles 6050 cycles Weight 320 g 345 g 370 g 395 g Operating Manual PSEN ml s 1.1/2.1/2.2 | 81 1004710-EN-05...

  • Page 82: Technical Details Escape Release 570471-570473

    Technical details for auxiliary release 570461 General Certifications Environmental data Temperature range 0 - 60 °C Mechanical data Release force escape release 80 N Service life escape release 6050 cycles Weight 100 g Operating Manual PSEN ml s 1.1/2.1/2.2 | 82 1004710-EN-05...

  • Page 83: Order Reference

    Mechanical safety gate system with 12-pin M12 connector 570406 guard locking, coded, for series con- nection PSEN ml s 1.1 unit r Mechanical safety gate system with 12-pin M12 connector 570436 guard locking, coded, for series con- nection, PSEN ml 1.1 round actuator PSEN ml s 1.1...
  • Page 84 Mounting bracket with handle unit for installing the actuator on a 570495 handle sliding door sliding gate, with 2 hexagonal socket head screws and 1 tamper- proof pan head locking screw, M5x16. Operating Manual PSEN ml s 1.1/2.1/2.2 | 84 1004710-EN-05...
  • Page 85 M12, 8-pin 540340 M12-8sf M12-8sm, male con- male con- nector, straight nector, straight PSEN cable M12, 8-pin fe- M12, 8-pin 540341 M12-8sf M12-8sm, male con- male con- nector, straight nector, straight Operating Manual PSEN ml s 1.1/2.1/2.2 | 85 1004710-EN-05...
  • Page 86 M12-12sm 10m nector, straight nector, straight PSEN cable 20 m M12, 12-pin fe- M12, 12-pin 570362 M12-12sf/ male con- male con- M12-12sm 20m nector, straight nector, straight Operating Manual PSEN ml s 1.1/2.1/2.2 | 86 1004710-EN-05...
  • Page 87 M12, 12-pin fe- M12, 8-pin 570487 apter male connector male connector PSEN ml / PSENcs M12, 8-pin fe- M12, 8-pin M12, 8-pin fe- 570489 Y junction M12 male connector male connector male connector Operating Manual PSEN ml s 1.1/2.1/2.2 | 87 1004710-EN-05...

  • Page 88: Appendix

    We recommend that you keep the completed check list and store it with the machine docu- mentation for reference. Date Action Safety Actuator OK Not OK Notes Signature switch Number Number Operating Manual PSEN ml s 1.1/2.1/2.2 | 88 1004710-EN-05...

  • Page 89: Ec Declaration Of Conformity

    European Parliament and of the Council. The complete EC Declaration of Conformity is available on the Internet at www.pilz.com/downloads. Authorised representative: Norbert Fröhlich, Pilz GmbH & Co. KG, Felix-Wankel-Str. 2, 73760 Ostfildern, Germany Operating Manual PSEN ml s 1.1/2.1/2.2...
  • Page 90 We are represented internationally. Please refer to our homepage www.pilz.com for further details or contact our headquarters. Headquarters: Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany Telephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: info@pilz.com, Internet: www.pilz.com...

This manual is also suitable for:

Psen ml s 2.1Psen ml s 2.2570408570411570410570409 ... Show all

Table of Contents