Table of Contents
Advertisement
10.8
Device Runtime
The DEVICE RUNTIME menu is used to assign a
runtime for a device or auxiliary.
When the device is turned on from the OTHER
EQUIPMENT ON/OFF menu, it will run for the
duration specified on the DEVICE RUNTIME menu.
A device runtime can be assigned to SPA,
NOTE
AUX1 - AUX31, EXTRA AUX, and macros
ONETOUCH1 - ONETOUCH6 from a minimum
of 1 minute to a maximum of 5 hours.
The default runtime of 30 minutes will be displayed.
10.8.1
To Set Up Device Runtime
MENU > SYSTEM SETUP > DEVICE RUNTIME
From the SYSTEM SETUP screen, touch the DEVICE
RUNTIME button to display the DEVICE RUNTIME
screen. On this screen, touch the device of your choice.
Enter your new time using the numeric keypad and
touch the ENTER button when finished.
Use the PAGE DOWN/PAGE UP button to view
additional devices. Touch the SAVE button to save the
updated settings and to exit this screen.
Device Run Time
Devices
Hrs/Min
Number of Spa Remotes
Spa
2:00
OneTouch 1
:30
OneTouch 2
:45
OneTouch 3
Off
OneTouch 4
Off
OneTouch 5
Off
OneTouch 6
Off
Aux 1
3:00
Page
Page
Save
Up
Down
Home
Menu OneTouch
Help
10.9
Maintain Temp
Maintain Temp is designed to operate outside
NOTE
(before or after) the normal filtration pump
times.
The MAINTAIN TEMP menu provides the ability to
specify how often the filter pump is turned on to sample
the water temperature. This feature allows for the
sampling interval to be set to one (1), two (2), or four
(4) hours. The default value will be two (2) hours.
AquaLink
®
Touch™ Owner's Manual
Thu January 1, 2009 3:03 PM
Set Time:
30
7
8
9
4
5
6
1
2
3
0
Clear
Enter
Back
Status
Photos
Power
10.9.1
To Set Up Maintain Temp
Note that the MAIN TAIN TEMP will run the pump
for the chosen body of water to keep the water at the
desired temperature, is this function is ON and the
heater/chiller (if installed) is enabled. The system will
au to mat i cal ly turn on the pump every couple of hours
for just enough time to test the water temperature. If the
temperature meets the set point, the pump will return to
off. If the measured temperature is different than the set
tem per a ture, the pump will stay on and the heater/chiller
will operate long enough to bring the wa ter to the set
tem per a ture.
MENU > SYSTEM SETUP > MAINTAIN TEMP
From the SET TEMPERATURE screen, touch the
MAINTAIN TEMP button to display the MAINTAIN
TEMP screen.
Maintain Temp
Heat
Start
Stop
Pool
10:00 AM
8:00 PM
Spa
7:00 PM
10:00 PM
Save
Home
Menu OneTouch
Help
Schedule the MAINTAIN TEMP as follows:
▪ On the MAINTAIN TEMP screen, touch the START time
of the selected equipment, and use the numeric keypad
to enter the new time.
▪ If you make a mistake, touch the CLEAR button and
re-enter new time again. Touch the ENTER button when
fi nished.
▪ To set the stop time, touch the STOP time of the
selected equipment and use the numeric keypad to
enter the new time.
▪ To set the sample time, touch the SAMPLE time of the
selected equipment and use the numeric pad to enter
the new sampling interval.
▪ Touch the ON/OFF button to enable or disable the
MAINTAIN TEMP schedule of the selected equipment.
▪ Touch SAVE when fi nished.
Page 37
Thu January 1, 2009 3:03 PM
Set:
:05
PM
Sample Status
7
8
9
–
Dis
2 Hrs
Ena
4
5
6
1
2
3
0
Clear
Enter
Back
Status
Photos
Power
Advertisement
Table of Contents
