Page 1
Jandy Pro Series JEP-R Variable-Speed Pump Digital Controller For use with Jandy Pro Series Variable-Speed Pumps For Indoor or Outdoor Installations WARNING FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exist.
Pump Freeze Protect Operation ......15 onto an Electrical Box ........8 Selecting Pump Type .........15 Installation of the Backplate Display Power Usage ........15 on a Flat Wall .............8 Connection to Jandy ® Pro Series Section 5. User Set Up Options ......16 variable-speed Pump .........8 Setting Time-of-Day ...........16...
PAGE 3 ENGLISH JEP-R Variable-Speed Pump Controller Installation Manual Section 1. IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS Safety Instructions All electrical work must be performed by a licensed electrician and conform to all national, state, and local codes. When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: WARNING...
Page 4
Notice: These parameters apply to Jandy Pro Series equipment only. For non-Jandy equipment, consult the equipment manufacturer. WARNING Due to the potential risk of fire, electric shock, or injuries to persons, Jandy Pumps must be installed in accordance with the National Electrical Code ® (NEC ®...
Page 5
PAGE 5 ENGLISH JEP-R Variable-Speed Pump Controller Installation Manual WARNING People with infectious diseases should not use a spa or hot tub. To avoid injury, exercise care when entering or exiting the spa or hot tub. Do not use drugs or alcohol before or during the use of a spa or hot tub to avoid unconsciousness and possible drowning.
PAGE 6 ENGLISH JEP-R Variable-Speed Pump Controller Installation Manual Pool Pump Suction Entrapment Prevention Guidelines WARNING SUCTION HAZARD. Can cause serious injury or death. Do not use this pump for wading pools, shallow pools or spas containing bottom drains, unless the pump is connected to at least two (2) functioning suction outlets.
PAGE 7 ENGLISH JEP-R Variable-Speed Pump Controller Installation Manual At Least 3 Feet Listed/Certified to latest Listed/Certified to latest published edition of published edition of ANSI ® /ASME ® A112.19.8 ANSI ® /ASME ® A112.19.8 or its successor standard, or its successor standard, ANSI/APSP-16 ANSI/APSP-16 Anti-entrapment...
Failure to comply may cause a shock hazard resulting in severe personal injury or death. Connection to Jandy Pro Series variable-speed Pump 3. Carefully detach the backplate from the controller by removing the six (6) screws from the front of the IMPORTANT controller.
ENGLISH PAGE 9 JEP-R Variable-Speed Pump Controller Installation Manual NOTE The controller uses a four-wire RS-485 interface controller or OFF if the pump is to be controlled by the to communicate with the ePump. ® AquaLink RS, AquaLink PDA or AquaLink Z4. See "Table 1.
ENGLISH PAGE 11 JEP-R Variable-Speed Pump Controller Installation Manual WARNING Basic Functions The controller has two (2) operational modes: User ELECTRICAL SHOCK HAZARD Mode and Setup Mode. Turn off all switches and the main breaker in the ePump™ electrical circuit before starting the User Mode procedure.
PAGE 12 ENGLISH JEP-R Variable-Speed Pump Controller Installation Manual Manual Start and Stop To adjust the pump speed, the controller must be in the mode. While in mode, the controller displays Up to eight (8) speeds may be started from the the pump speed.
ENGLISH PAGE 13 JEP-R Variable-Speed Pump Controller Installation Manual Keypad Lock Press and hold both arrow keys for five (5) seconds to lock the keypad. To disable the keypad lock, repeat the 2:SPEED 2 TIMECLOCK procedure while the keypad is locked. ENABLE KEYPAD LOCKED 12:00AM...
PAGE 14 ENGLISH JEP-R Variable-Speed Pump Controller Installation Manual To set the minimum speed, from the service setup menu, Last Fault select SET MIN LIMIT using the arrow keys. Press This feature shows on the top display line, the most .
ENGLISH PAGE 15 JEP-R Variable-Speed Pump Controller Installation Manual To set priming duration, select PRIMING DURATION using the arrow keys. Press MENU . Using the arrow WARNING keys, set the priming speed to the desired value in minutes from one (1) to five (5) minutes. Press Freeze protection is intended to protect equipment and MENU plumbing for short periods of freezing only.
PAGE 16 ENGLISH JEP-R Variable-Speed Pump Controller Installation Manual To disable the power display feature, from the service currently selected speed. Using the arrow keys, choose setup menu select DISPLAY POWER USAGE . Press the speed to be changed. Press MENU to select.
ENGLISH PAGE 17 JEP-R Variable-Speed Pump Controller Installation Manual From the setup menu, select DISPLAY LIGHT . Press Password Protect MENU . Using the arrow keys, select the desired Entry into the USER SETUP MENU may be restricted operating mode for the display backlight: by the setting of a four-digit password.
[1, 4] after execution. SET SPEED 11. Minimum operating speed is 1050 RPM for Jandy Pro [2750 RPM] Series SVRS-equipped pumps. 12. Minimum priming speed is 1500 RPM for Jandy Pro Series SVRS-equipped pumps. SET SPEED SPEED 5-8 MENU MENU...