Table of Contents
Advertisement
APPENDIX B
APPENDIX B TABLES AND FIGURESB.1 TABLES
T
: 1–1 ORDER CODES FOR THE LPS-O........................................................................................................... 1-3
ABLE
T
: 1–2 LPS-O MEASUREMENT FUNCTIONS .................................................................................................... 1-5
ABLE
T
: 1–3 LPS-O DEFAULT CONTACT CONVERTER ASSIGNMENTS................................................................. 1-6
ABLE
T
: 1–4 LPS-O DEFAULT OUTPUT CONTACT ASSIGNMENTS......................................................................... 1-7
ABLE
T
: 1–5 TRUTH TABLE FOR SETTINGS GROUP.............................................................................................. 1-14
ABLE
T
: 1–6 SETTINGS GROUP SWITCH 16SB1_______ ....................................................................................... 1-14
ABLE
T
: 2–1 TRIPPING SCHEMES .............................................................................................................................. 2-4
ABLE
T
: 2–2 SETTING FORMAT FOR NUM_MON ...................................................................................................... 2-5
ABLE
T
: 2–3 OSCILLOGRAPHY CYCLES PER STORAGE EVENT ........................................................................... 2-7
ABLE
T
: 2–4 FIXED VALUES FOR PROTECTION SETTINGS 503 TO 505 .............................................................. 2-14
ABLE
T
: 2–5 INDEX NUMBERS – CONTACT CONVERTER INPUT ASSIGNMENT................................................. 2-32
ABLE
T
: 2–6 INDEX NUMBERS – CONFIGURABLE LOGIC & PROGRAMMABLE OUTPUT SIGNALS .................. 2-33
ABLE
T
: 2–7 PROTECTION SETTINGS GUIDE ......................................................................................................... 2-37
ABLE
T
: 2–8 GENERAL SETTINGS GUIDE................................................................................................................ 2-44
ABLE
T
: 2–9 PROTECTION SETTINGS DATA SHEET .............................................................................................. 2-47
ABLE
T
: 2–10 GENERAL SETTINGS DATA SHEET .................................................................................................. 2-54
ABLE
T
: 3–1 JUMPER POSITION ................................................................................................................................. 3-9
ABLE
T
: 4–1 AVAILABLE RELAY TESTS ..................................................................................................................... 4-5
ABLE
T
: 4–2 FACTORY DEFAULT COMMUNICATIONS PARAMETERS ................................................................... 4-7
ABLE
T
: 4–3 DIGITAL OUTPUTS TEST CONNECTIONS .......................................................................................... 4-12
ABLE
T
: 5–1 TIME-OUT VALUES WHILE REPEATING T8 .......................................................................................... 5-6
ABLE
T
: 5–2 FAULT CURRENT PHASE SETTINGS FOR TEST T11 ........................................................................ 5-10
ABLE
T
: 5–3 FAULT CURRENT PHASE SETTINGS FOR TEST T12 ........................................................................ 5-11
ABLE
T
: 5–4 FAULT CURRENT PHASE SETTINGS FOR T13 .................................................................................. 5-12
ABLE
T
: 5–5 FAULT CURRENT PHASE SETTINGS FOR TEST T14 ........................................................................ 5-14
ABLE
T
: 5–6 FAULT CURRENT PHASE SETTINGS FOR TEST T17 ........................................................................ 5-20
ABLE
T
: 6–1 TEST CURRENT RANGES FOR PHASE-TO-PHASE REACH ............................................................... 6-9
ABLE
T
: 8–1 PASSWORD ENCRYPTION KEY TABLE .............................................................................................. 8-24
ABLE
T
: 8–2 KEYPAD / DISPLAY INTERFACE ERROR MESSAGES....................................................................... 8-25
ABLE
T
: 8–3 HARDWARE SWITCH DESCRIPTIONS ................................................................................................ 8-27
ABLE
T
: 8–4 COMMAND SEQUENCE SENT BY LPSO-L
ABLE
T
: 8–5 CONFIGURATION SETTINGS FOR THE MODEM CONNECTED TO THE RELAY............................. 8-29
ABLE
T
: 8–6 MODEM COMMANDS FOR COMMUNICATION BETWEEN RELAY AND PC ..................................... 8-31
ABLE
T
: 9–1 COMPONENTS TESTED DURING START-UP TESTS .......................................................................... 9-2
ABLE
T
: 9–2 RUN-TIME BACKGROUND SELF-TESTS ............................................................................................... 9-3
ABLE
T
: 9–3 RUN-TIME FOREGROUND SELF-TESTS............................................................................................... 9-3
ABLE
T
: 9–4 SYSTEM STATUS ERROR MESSAGES ................................................................................................. 9-4
ABLE
T
: 10–1 INPUT QUANTITIES............................................................................................................................. 10-3
ABLE
T
: 12–1 ASCII PROMPTS .................................................................................................................................. 12-1
ABLE
T
: 12–2 OSCILLOGRAPHY DATA STRUCTURE.............................................................................................. 12-2
ABLE
T
: 12–3 ASCII COMMAND LIST ........................................................................................................................ 12-2
ABLE
T
: 13–1 PICKUP DELAY TIMER TRUTH TABLE .............................................................................................. 13-7
ABLE
T
: 13–2 CONTACT CONVERTER INPUT FLAGS............................................................................................. 13-8
ABLE
T
: 13–3 CONFIGURABLE INPUTS.................................................................................................................... 13-9
ABLE
T
: 13–4 SCHEME LOGIC INPUTS .................................................................................................................... 13-9
ABLE
T
: 13–5 CURRENT AND VOLTAGE UNITS ...................................................................................................... 13-9
ABLE
T
: 13–6 SCHEME LOGIC OUTPUTS ............................................................................................................. 13-10
ABLE
T
: 13–7 DISTANCE UNITS .............................................................................................................................. 13-11
ABLE
T
: 13–8 MISCELLANEOUS.............................................................................................................................. 13-11
ABLE
T
: 13–9 USER DEFINABLE OUTPUT FLAGS................................................................................................. 13-12
ABLE
GE Power Management
TO MODEM ................................................................ 8-28
INK
LPS-O Line Protection System
B.1 TABLES
B.1.1 LIST OF TABLES
B-
1
B
Advertisement
Table of Contents
