ADTRAN TOTAL ACCESS 600R User Interface Manual page 43

NAT V
64200600L1#T-31A
P
RIVATE
A
DDRESS
M
ODE
P
RIVATE
A
DDRESS
P
RIVATE
P M
ORT ODE
P
RIVATE
P
ORT
T
RANSLATE
B
ODY
Shows the protocols that are actively being translated.
IEW
P A This option is only available when
RIV DDR
abled. This shows the private address of the host that the entry is
used for.
P A This option is only available when
UB DDR
abled. This shows the public address this entry is using for its
NAPT.
S A This option is only available when
ERV DDR
abled. This is the destination of the packet.
P This option is only available when
ROTO
abled. This shows the protocol used (
P P This option is only available when
RIV ORT
abled. This is the private port used for the entry.
This option is only available when
S P
POOF ORT
abled. If the same private port is already used in the table, it will
spoof a different port for the entry.
© 2002, ADTRAN, Inc.
Total Access 600R User Interface Guide (UIG)
This option is only available when
is enabled. The private IP address can be speci-
LATION
fied to steer certain protocols and ports to specific
servers in the private network. Likewise, internal hosts
can be steered to certain servers on the public network.
A new request from the public network matching this
entry's public parameters will be dropped if this mode
is set to A . Choices are S
I
NY NTERNAL
. Default is A
A I
NY NTERNAL
This option is only available when
is enabled and
P
LATION RIVATE
. Default is 0.0.0.0.
S
PECIFIED
This option is only available when
is enabled. However, it will not be available if
LATION
is set to ICMP; A
P M
ROTOCOL ODE
ICMP); A ; S
OR LL PECIFIED
The private destination port associated with this entry
can be specified to add more control over certain types
of traffic. Leave as A
P
NY
Choices are A and S
P
NY ORT
.
A P
NY ORT
This option is only available when
is enabled and the
LATION
. However, it will not be available if
S
PECIFIED
is set to ICMP; A
M
COL ODE
ICMP); A ; S
LL PECIFIED
mal).
This option is only available when
is enabled. When set to
LATION
payload in the packet is scanned for occurrences of the
private/public IP address in binary or ASCII form. Set
this to (default) for applications where this will
No
cause problems.
NAT P
NAT P
NAT P
NAT P
NAT P
NAT P
NAT P T
ORT RANS
and
PECIFIED
I .
NY NTERNAL
NAT P T
ORT RANS
is set to
A M
DDRESS ODE
NAT P T
ORT RANS
(TCP, UDP,
NY
or N
.
ONE
to cover all port types.
ORT
. Default is
PECIFIED
NAT P T
ORT RANS
is set to
P P M
RIVATE ORT ODE
P
ROTO
(TCP, UDP,
NY OR
or N . Default is 0 (deci-
ONE
NAT P T
ORT RANS
, the application
Y
ES
is en-
T
ORT RANSLATION
is en-
T
ORT RANSLATION
is en-
T
ORT RANSLATION
is en-
T
ORT RANSLATION
, etc.).
TCP, UDP, ICMP
is en-
T
ORT RANSLATION
is en-
T
ORT RANSLATION
-
-
-
-
-
-
Page 43