Reset Function - Beretta EXCLUSIVE R Installer And User Manual

SELECT DAYS ON WHICH YOU WANT
SELECT DAYS ON WHICH YOU WANT TO COPY SCHEDULE
TO COPY SCHEDULE OF THURSDAY
MON TUE
MON TUE
USE THE ARROWS TO MODIFY
USE THE ARROWS TO MODIFY
The day will be highlighted and others can be selected using the same
procedure. When finished highlight
SELECT DAYS ON WHICH YOU WANT
SELECT DAYS ON WHICH YOU WANT TO COPY SCHEDULE
TO COPY SCHEDULE OF THURSDAY
MON TUE
MON TUE
USE THE ARROWS TO MODIFY
USE THE ARROWS TO MODIFY
In order to confirm that the operation has been completed successfully, the
display will show the list of days to which the scheduled programme has
been copied.
SCHEDULE OF THURSDAY
SCHEDULE OF THURSDAY WILL BE COPIED ON THE DAYS
WILL BE COPIED ON THE DAYS :
TUESDAY
USE THE ARROWS TO MODIFY
USE THE ARROWS TO MODIFY
14 FAULTS
If any faults should occur, a screen will appear on the display indicating
the relative error code and a brief alphanumeric description of the same.
Pressing the "back" button it is possible to return to the main screen,
where a fault is signalled by this flashing icon
The user can return to the fault description screen by using the "up" and
"down" keys and then pressing the "ok" key. The faults description screen
is automatically displayed once the display illumination time has elapsed
without any button being pressed.
Press the "up" and "down" keys to display the descriptions of any other
faults that may be present.
FRI
FRI
18/05/2013
MENU
MENU
INFO
INFO
HOT WATER TEMPERATURE
HOT WATER TEMPERATURE
or fault E041
F
If the pressure drops below the safety threshold of 0.3 bar the boiler displays
the fault code "E041 - WATER TRANSDUCER FILL THE SYSTEM" for a
transitional time of 10 min during which it is possible to open the external
filling tap until the pressure is between 1 and 1.5 bar.
MAIN
MAIN
OF THURSDAY
WED THU FRI
WED THU FRI
SAT SUN
SAT SUN
CONFIRM
CONFIRM
CONFIRM and press "ok".
MAIN
MAIN
OF THURSDAY
WED THU FRI
WED THU FRI
SAT SUN
SAT SUN
CONFIRM
CONFIRM
MAIN
MAIN
: TUESDAY
.
PLANT
PLANT
12:17
1.3 bar STATE
STATE
42
°C
SET
SET
WATER TRANSDUCER
WATER TRANSDUCER
b
If the pressure drops frequently, contact the Technical Assistance
Centre.
For fault E091
The boiler has an auto-diagnostic system which, based on the total number
of hours in certain operating conditions, can signal the need to clean the
primary heat exchanger.
The intervention of the Technical Assistance Centre is necessary.

14.1 Reset function

In order to reset the boiler's operation in the event of a fault, it is necessary
to access the fault description screen. If the lockout is of a non-volatile type
that requires a reset procedure, this will be indicated on the screen, and can
be carried out by pressing the "ok" button on the REC10.
LIMIT THERMOSTAT
LIMIT THERMOSTAT
PRESS OK TO RESET
PRESS OK RESET
At this point, if the correct operating conditions have been restored, the
boiler will restart automatically.
If the attempts to reset the fault do not restore the boiler's functionality,
please contact your local Technical Assistance Centre.
Up to a maximum of 3 reset attempts can be made using the REC10, after
which the machine must be disconnected from the power supply to reset
the number of attempts available.
b
Request the intervention of the Technical Assistance Centre.
LIMIT THERMOSTAT
LIMIT THERMOSTAT
RESET ATT. EXHAUSTED
REC10 ATTEMPTS EXHAUSTED
E041
FILL THE SYSTEM
LOAD THE SYSTEM
E020
E020
ENGLISH
33