Specifications - EBARA EVMSU Operation, Installation & Maintenance Manual Operation, Installation & Maintenance Manual

7. PRODUCT SPECIFICATIONS
EVMSU(L)1-3-5-10-15-20
Version
N o m n i a s l z i e
HP
Performance
range
Capacity
Total Head
Type of liquid
Liquid
Maximum working pressure
Handling
Liquid temperature range
Suction
Size
Discharge
Impeller
Intermediate casing
Liner ring
Bottom casing
Casing cover
Shaft
Shaft sleeve bearing
Key
Component
Shaft Seal
Materials
O-ring
Outer casing
Motor bracket
Tie rod
Coupling
Base
Oval flange
Round flange
(ANSI compatible raised face)
Pipe
Loose round flange
connection
(ANSI compatible raised face)
victaulic
Clamp
Type
Speed
Motor Power Requirements
Direction of Rotation
Motor Options
EBARA
www.pumpsebara.com
PUMP
1
AISI 304 (EN 1.4301) + PPS
AISI 304 (EN 1.4301)
AISI 316L (EN 1.4404) EVMSUL 1-3-5, EVMSUL 10-15-20 (depending on model)
AISI 329A (EN 1.4462)
SiC/Carbon/FPM
SiC+Graphite/SiC/FPM
SiC/Carbon/EPDM
SiC+Graphite/SiC/EPDM
FPM
EPDM
up to 5 HP
from 7 1/2 HP
up to 230 PSI
up to 230 PSI
from 230 PSI to 360 PSI
up to 230 PSI
from 230 PSI to 360 PSI
up to 230/360 PSI
up to 230/360 PSI
3 Phase, 230/460V or 208-230/460V - Single Phase, 115/230V
Pumps Americas Corporation
EVMSU
3 5 1 0 1 5 2 0 1
1/2 to 25 HP
2.9 to 132.1 gpm
24.3 to 860 ft
Clean water (for other clean liquids, consult factory)
230 / 375 PSI (depending on model)
-22°F to 248°F (-30°C to 120°C)
1 / 1 " 4 2"
1 1/4" 2"
AISI 304 (EN 1.4301)
AISI 304 (EN 1.4301)
AISI 316 (EN 1.4401) + PPS
AISI 304 (EN 1.4301)
AISI 304 (EN 1.4301)
EVMSU 1-3-5, EVMSU 10-15-20 (depending on model)
EVMSU / EVMSUL 5-15-20 (depending on model)
Tungsten carbide
AISI 304 (EN 1.4301)
Cast Iron
AISI 431 (EN 1.4057)
Die cast aluminium
Cast Iron
Die cast aluminium
NEMA C/TC/TSC frame, TEFC or ODP enclosure
2-pole, 60 Hz, 3500 RPM
Clockwise when viewed from motor end
Consult factory for optional motor types
Legend:
EVMSUL
3 5 1 0 1 5 2 0
1 / 1 " 4 2"
1 1/4" 2"
AISI 316 (EN 1.4401)
AISI 316 (EN 1.4401)
AISI 316 (EN 1.4401)
AISI 316 (EN 1.4401)
AISI 316L (EN 1.4404)
Standard Options
5
rev. 01/19