Husqvarna AUTOMOWER 310 Operator's Manual page 31

To enable the GeoFence function
GeoFence is a GPS-based theft protection that makes a
virtual fence for the product. You will get a message if
the product is moved on the other side of the GeoFence.
1. Put the product in the center of the work area.
To get access to the menu in the
2. Do steps 1–3 in
display of the product on page 23 .
3. Use the arrow buttons and the OK button to move
through the menu structure
Automower Connect > GeoFence > Activate
GeoFence .
4. Push the OK button.
Activate GeoFence and push the OK
5. Select
button.
To set a new center point for the Geofence function
1. Put the product in the center of the work area.
2. Do steps 1–3 in To get access to the menu in the
display of the product on page 23 .
3. Use the arrow buttons and the OK button to move
through the menu structure
Automower Connect > GeoFence > New center
point .
4. Push the OK button.
To set the GeoFence level of sensitivity
The higher level of GeoFence sensitivity, the easier the
alarm starts.
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Automower Connect > GeoFence .
3. Use the arrow buttons to select level of GeoFence
sensitivity.
4. Push the BACK button.
To use the SMS function
The SMS function sends you an SMS when the product
is moved out of the GeoFence.
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Automower Connect > Communication > Use
SMS .
3. Push the OK button.
4. Use the arrow buttons and the OK button to move
through the menu structure
Automower Connect > Communication > SMS
phone numbers .
5. Push the number buttons to enter the telephone
number with country code. For example
(+)46701234567.
6. Push the BACK button.
1440 - 004 - 24.03.2021
Note:
from the product.
Network
APN settings
The product must specify APN settings to be able to use
and send data via the mobile net. Settings for
Husqvarna SIM is default.
Accessories >
3.12.9.3 Headlights Automower
To set the schedule for the headlights
1.
2.
3.
To set the Flashes when fault function
Accessories >
The headlights flashes if the product stops to operate
because of a fault if
1.
2.
3.
3.12.9.4 To avoid collisions with the Automower
Accessories >
The wear on the product and the Automower
decreases when you select
1.
2.
Note:
result in grass that is not cut around the charging
station.
Accessories >
Accessories >
There is a maximum of 10 SMS each month
®
315X
To get access to the menu in the
Do steps 1–3 in
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Accessories >
through the menu structure
Headlights > Schedule .
Select between Always ON , Evening only
Evening & night (19:00-07:00) or
(19:00-00:00),
Always OFF .
Flashes when fault is enabled.
To get access to the menu in the
Do steps 1–3 in
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Accessories >
through the menu structure
Headlights > Flashes when fault .
Use the OK button to enable or disable the
Flashes when fault function.
Avoid collisions with mower .
To get access to the menu in the
Do steps 1–3 in
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Accessories > Mower
through the menu structure
house > Avoid collisions with mower .
Avoid collisions with mower is selected it can
If
®
house
®
house
Installation - 31