Husqvarna AUTOMOWER 310 Operator's Manual page 30

3.12.8.4 Slope control
In order to decrease lawn wear near the boundary wire
in slopes, the product prevents to move in the opposite
direction when the product operates in a slope.
control is enabled in the factory settings.
To set the Slope control
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
control > Use Slope control .
3. Push the BACK button.
3.12.8.5 General
In General you can change the general settings of the
product.
To set the time & date
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Time & Date .
3. Use the number buttons to set the time and then
push the BACK button.
4. Use the number buttons to set the date and then
push the BACK button.
5. Use the arrow buttons to set the time format and
then push the BACK button.
6. Use the arrow buttons to set the date format and
then push the BACK button.
To set the language
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Language.
3. Use the arrow buttons to select language and then
push the BACK button.
To set the Country & Timezone
1. Do steps 1–3 in To get access to the menu in the
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Country & Timezone.
3. Use the arrow buttons to select country and then
push the BACK button.
To set the unit format
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Unit format.
30 - Installation
3.
To reset all user settings
Slope
1.
2.
3.
Settings > Slope
4.
Note:
Messages, Date & Time, Language and Country
settings are not reset.
The About menu
The
for example serial number and firmware versions.
3.12.9 Accessories
Settings > General >
Settings for accessories mounted on the product can be
made in this menu.
3.12.9.1 Information
This menu handles accessories mounted on the
product. Contact your local Husqvarna representative for
more information on available accessories.
3.12.9.2 Automower
The product can connect to mobile devices that have the
Automower
Settings > General >
Connect app has Long-range cellular connectivity and
Short-range Bluetooth
Automower
Note:
your product while the mobile device have connection
with the mobile network and the product is switched on.
Settings > General >
Note:
Connect because of regional specified cellular systems.
The included Automower
applies if there is a third part sub-supplier of 2G/3G/4G
available in the operational area. In some countries
Bluetooth
Settings > General >
Use the arrow buttons to select unit format and
then push the BACK button.
Do steps 1–3 in To get access to the menu in the
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Settings > General >
through the menu structure
Reset all user settings .
Use the right arrow button to select
reset of all user settings?
Push the OK button to reset all the user settings.
Security level, PIN code, Loop signal,
About menu displays information about the product,
®
Connect
®
Connect app installed. The Automower
®
connectivity. Refer to
® Connect app on page 22 .
®
Automower Connect is always connected to
All countries do not support Automower
®
Connect life-time service only
®
is not available because of legal reasons.
1440 - 004 - 24.03.2021
Proceed with
®
®