Husqvarna AUTOMOWER 310 Operator's Manual page 24

3.12.3.3 To copy the schedule setting
1. Do steps 1–3 in To get access to the menu in the
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Copy .
3. Use the arrow buttons and the OK button to copy
the schedule setting. You can copy the schedule
settings day to day or for the full week.
3.12.3.4 To reset the schedule setting
You can remove all schedule settings and use the
factory setting.
1. Do steps 1–3 in To get access to the menu in the
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Reset .
a) Push the arrow buttons to select
to only reset the current day to factory
settings.
b) Push the arrow buttons to select
reset all schedule settings to factory settings.
3. Push the OK button.
3.12.4 Security level
There are 3 security levels for the product.
Function Low
Alarm
PIN-code
Time lock
X
Alarm - An alarm goes off if the PIN-code is not
•
entered within 10 seconds after the STOP button is
pushed. The alarm also goes off when the product
is lifted. The alarm stops when the PIN-code is
entered.
PIN-code - The correct PIN-code must be entered
•
to get access to the Menu structure of the product.
If the incorrect PIN-code is entered 5 times, the
product is locked for a time. The lock is extended
for each new incorrect try.
24 - Installation
•
3.12.4.1 To set the security level
Schedule > Overview >
Select 1 of 3 security levels for your product.
1.
2.
3.
4.
3.12.4.2 To create a New loop signal
The loop signal is randomly selected to create a unique
link between the product and the charging station. In
rare cases, there may be a need to generate a new
signal, for instance if two adjacent installations have a
very similar signal.
1.
2.
Schedule > Overview >
3.
Current day
4.
All week to
3.12.4.3 To change the PIN-code
1.
2.
3.
4.
5.
Medium High
6.
X
7.
X X
3.12.4.4 To change the duration of the alarm
X X
1.
2.
3.
4.
Time lock - The product locks if the PIN-code has
not been entered in 30 days. Enter the PIN-code to
get access to the product.
To get access to the menu in the
Do steps 1–3 in
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Settings > Security >
through the menu structure
Security level .
Use the arrow buttons and the OK button to select
the level of security.
Push the OK button.
Place the product in the charging station.
Do steps 1–3 in To get access to the menu in the
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Security > Advanced >
through the menu structure
New loop signal .
Await confirmation that the loop signal has been
generated. This normally takes about 10 seconds.
To get access to the menu in the
Do steps 1–3 in
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Settings > Security >
through the menu structure
Advanced > Change PIN-code .
Enter the new PIN code.
Push the OK button.
Enter the new PIN code again.
Push the OK button.
Make a note of the new PIN code. Refer to
Introduction on page 3 .
To get access to the menu in the
Do steps 1–3 in
display of the product on page 23 .
Use the arrow buttons and the OK button to move
through the menu structure Security > Advanced >
Duration > Duration of alarm .
Use the arrow buttons to select a time interval of 1
to 20 minutes.
Push the BACK button.
1440 - 004 - 24.03.2021