Husqvarna AUTOMOWER 310 Operator's Manual page 27

3. Push the OK button.
4. Push the BACK button.
To reset the Lawn Coverage settings
You can reset the Lawn Coverage settings for each area
and use the factory setting.
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Coverage > Area 1-3 > More > Reset .
3. Push the OK button.
3.12.7.2 Methods for the product to find the charging
station
The product has 3 search methods to find the charging
station :
• Irregular - The product moves in the work area until
it finds the signal of the charging station.
• Guide wire - The product moves in the work area
until it finds the guide wire. The product moves
along the guide wire to the charging station.
• Boundary wire - The product moves in the work
area until it finds the boundary wire. The product
moves along the boundary wire to the charging
station.
The factory setting is set to mix the 3 search methods.
When the battery is low the product starts to search for
the charging station with the irregular method for 3 min.
After 3 min the product changes search method to the
guide wire method. The product tries to find the guide
wire for 8 min. After 11 min the product changes search
method to the boundary wire method.
You can change the settings for how the product finds
the charging station to adapt to the work area.
To set how the product finds the charging station
You can make manual settings to make the product
search for the guide wire or the boundary wire in 0–30
min from when the battery is low.
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
the charging station > Overview of search methods
> Guide .
3. Push the arrow buttons to select 1 of the guide
wires.
4. Push the number buttons to set the time.
5. Push the OK button.
6. Push the BACK button.
7. Use the arrow buttons and the OK button to move
through the menu structure
the charging station > Overview of search methods
> Boundary wire .
8. Push the number buttons to set the time.
1440 - 004 - 24.03.2021
9.
10. Push the START button and close the hatch.
To do a test of the guide wire
1.
2.
Installation > Lawn
3.
4.
5.
6.
7.
To do a test of the boundary wire
1.
2.
3.
4.
5.
6.
7.
To change the signal range of the charging station
Installation > To find
1.
2.
3.
4.
Installation > To find
Push the OK button.
Do steps 1–3 in To get access to the menu in the
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Installation > Find
through the menu structure
charging station > Guide > More > Test guide .
Put the product 3 m / 9 ft. from the guide wire,
facing the guide wire.
Push the START button and close the hatch.
Make sure the product follows the guide wire to the
charging station.
Make sure the product docks with the charging
station.
If the product does not dock with the charging
station, change the position of the charging station
To install the charging
or the guide wire. Refer to
station on page 19 and To install the guide wire on
page 20 .
Put the product 3 m / 9 ft. from the boundary wire,
facing the boundary wire.
To get access to the menu in the
Do steps 1–3 in
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Installation > Find
through the menu structure
charging station > Overview of search methods >
Boundary > More > Test right / Test left .
Push the START button and close the hatch.
Make sure the product follows the guide wire to the
charging station.
Make sure the product docks with the charging
station.
Change the position of the charging station or the
guide wire if the product does not dock with the
charging station. Refer to To install the charging
station on page 19 and To install the guide wire on
page 20 .
To get access to the menu in the
Do steps 1–3 in
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Installation > Find the
through the menu structure
charging station > Overview of search methods >
Charging station range .
Use the left arrow button to select
Push the BACK button.
MAX, MID, MIN .
Installation - 27