Figure 8: Com Port Selection Within; Hyperterminal; External Modem Connection - Bosch D9412GV2 Program Entry Manual

D9412GV2/D7412GV2 | Program Entry Guide | 6.0
Figure 8: Com Port Selection within HyperTerminal
Figure 9: External Modem Connection
1 - Remote Programming Software (RPS)
2 - Modem
3 - PSTN
Bosch Security Systems | 5/05 | F001U003636B
GV2AUX
P3
D9133DC
1 2 4 8
4 - D9412GV2/D7412GV2 Control Panel
5 - Standard serial cable
6 - SDI bus
EN | 124
F01U003643B
LEDs Off When Normal
D9412GV2
YEL Charging Status
Digital Alarm Communicator Transmitter
Low Battery - 12.1 VDC
RED Refer to D9412GV2/D7412GV2 Approved Applications Compliance Guide (P/N: F01U003639___)
For System Wiring Diagram, Issue A
Disable all except Battery
10.2 VDC - Battery Load Shed Refer to D9412GV2/D7412GV2 Approved Applications Compliance Guide (P/N: F01U003639___)
Charging and Programming
For Compatible Smoke Detectors
POWER SUPPLY REQUIREMENTS PERIPHERAL DEVICE CONNECTIONS
CLASS 2 TRANSFORMER The Power Supply provides a maximum of 1.4 Amps for the Control Panel and all
RED
16.5 VAC 40 VA 60 H z Accessory Devices. For System Loading, refer to D9412GV2/D7412GV2
Model D1640 Operation and Installation Guide (P/N: F01U003641___).
Internally Fused - Do not short
All external connections except Terminal 5 (battery positive) are inherently power
Requires Unswitched Outlet YELLOW
Do not share with other equipment
limited. Requirements for battery standby time might reduce allowable output.
CAUTION:
See D9412GV2/D7412GV2 Operation and Installation Guide
+ AUX POWER
GREEN
(P/N: F01U003641) for Power Requirements relating to Terminals 6 and 7 .
WARNING!
BATTERY NEGATIVE ONLY
BLACK
CAUTION: Avoid damage to Panel. Multi-Battery installation requires Battery: Replace every 3 to
Do not connect 24 V to term inals.
Model D122 Dual Battery Harness. 5 years with Model D126, 12 V
Maximum charging current 1.4 A
Improper installation can be a fire 7 Amp Hr Lead Acid Battery
N.F.P.A.
BATTERY POSITIVE ONLY ZON EX OUT 1
hazard. Style 3.5
Signaling
This equipment should be installed in accordance with the NFPA 70 (National Electrical Code)
PROGRAMMABLE Line
RELAY A
ALARM OUTPUTS and NFPA 72 (National Fire Alarm Code) for Local, Central Station, Remote Station, Proprietary and Circuits
Terminals Household Fire Warning Systems and under the lim its of the Local Authority Having Jurisdiction
(National Fire Protection Association, Battermarch Park, Quincy, MA 02269). Printed inform ation
RELAY B 6 and 7 ZONEX OUT 2
describing proper installation, operation, testing, maintenance, evacuation planning and repair
SWITCHED AUX service is to be provided with this equipment.
Terminal D9412GV2 Control/Communicator is UL Listed For Central Station, Local, Remote Station and
RELAY C
8 Household Fire Alarm, and Central Station, Local, Police Station Connect, Household Burglar Alarm
and Encrypted Line Security when communicating via a network.
System is intended to be checked by a Qualified Technician at least every 3 years.
ZONEX POWER +
COMMON The types of initiating circuits the panel has been approved for are A, M, W, SS.
VOLTAGE RANGES
Open 3.7 - 5.0 VDC
EARTH GROUND ZONEX COMMON
Normal 2.0 - 3.0 VDC
Short 0.0 - 1.3 VDC
GROUND FAULT DETECT
Point 1 Point 2 Point 3 Point 4 Point 5 Point 6 Point 7 Point 8
Point 8
Enabled
Disabled S3 Option
Closed = 1KΩ EOL
ON when
PHONE communicating Normal Operation
LED OFF when idle
PHONE LINE SEIZED Open =AB-12 UL
Bell Box 220 KΩ
TIP RING 11 12 13 14 15 16 17 18 19 20 21 22
TELCO CORD GRN
MODEL D161
SDI
PWR
SDI
A
SDI
B
SDI
COM
P2
SER RX TX RX TX BUS
SDI Connector
Reset Pin
POWER +
DATA BUS A
DATA BUS B
COMMON
ZONEX IN 1
26
25
ZONEX IN 2
24
23
D5200
PROG CONN