Tabletop & Rack Mount Analyzers - Emerson Rosemount Analytical X-STREAM Enhanced Series Short Form Manual

Short Form Manual
HASXEE-SFM-HS
05/2017
A.2 Assignment of Terminals and Sockets
A.2.1 Tabletop & Rack Mount Analyzers
Signal Pin
Channel 1, (+) 4 (0) - 20 mA 1
Channel 2, (+) 4 (0) - 20 mA 2
Channel 3, (+) 4 (0) - 20 mA 3
Channel 4, (+) 4 (0) - 20 mA 4
Channel 5, (+) 4 (0) - 20 mA 5
unused 6
unused 7
Output1 (Failure) NC 8
Output1 (Failure) NO 9
Output1 (Failure) COM 10
Output3 (Off spec) NC 11
Output3 (Off spec) NO 12
Output3 (Off spec) COM 13
Socket X1 - Analog outputs, relay outputs 1...5
(Assignment of screw terminals adaptor: see XSTA on next page)
Signal Pin
Input 1 1
Input 2 2
Input 3 3
Input 4 4
GND for all digital inputs 5
unused 6
unused 7
Output 5 NC 8
Output 5 NO 9
Output 5 COM 10
Output 6, NC 11
Output 6, NO 12
Output 6, COM 13
Output 7, NC 14
Output 7, NO 15
Output 7, COM 16
Output 8, NC 17
Output 8, NO 18
Output 8, COM 19
Socket X4 - Digital I/O
(Assignment of screw terminals adaptor: see XSTD on next page)
Emerson Process Management GmbH & Co. OHG
A.2 Assignment of Terminals and Sockets
Pin Signal
14 Channel 1, GND
15 Channel 2, GND
16 Channel 3, GND
17 Channel 4, GND
18 Channel 5, GND
19 unused
20 Output2 (Maintenance request) NC
21 Output2 (Maintenance request) NO
22 Output2 (Maintenance request) COM
23 Output4 (Function check) NC
24 Output4 (Function check) NO
25 Output4 (Function check) COM
Note!
Configuration of relay contacts as per standard
factory setting (NAMUR status signals). NAMUR
status signals are automatically configured Fail
Safe!
Pin Signal
20 Input 5
21 Input 6
22 Input 7
23 Output 9, NC
24 Output 9, NO
25 Output 9, COM
26 Output 10, NC
27 Output 10, NO
28 Output 10, COM
29 Output 11, NC
30 Output 11, NO Note!
31 Output 11, COM
The configuration illustrated
32 Output 12, NC
here is that of the first socket,
33 Output 12, NO
labelled X4.1.
34 Output 12, COM
Inputs 8-14 and outputs 14-
35 Output 13, NC
36 Output 13, NO 22, are on the second socket
37 Output 13, COM
(X4.2), if installed.
Pin
Pin
1
6
2
7
3
8
4
9
5
MOD 485/ MOD 485/
Pin no. RS 232
2 wire 4 wire
1 Common Common Common
2 not used not used
3 not used not used
4 RXD1(+)
not used
5 D1(+) TXD1(+) Common
6 not used not used
7 not used not used
8 RXD0(-)
not used
9 D0(-) TXD0(-)
Connector X2 - IOIOI - Serial Modbus interface
(Assignment of screw terminals adaptor: see XSTA on next
page)
Signal Pin
Pin
{
}
BR 2 fit a wire bridge here to apply analog 5
BR 2 signal in current mode to input 2 *) 4
unused 3
{ }
BR 1 fit a wire bridge here to apply analog 2
BR 1 signal in current mode to input 1 **) 1
alternatively set jumper P1 on electronics board XASI
*)
alternatively set jumper P2 on electronics board XASI
**)
Connector X5 - Analog inputs
(Assignment of screw terminals adaptor: see XSTI on next page)
X-STREAM XE
3
RXD
TXD
1
not used
2
not used
not used
not used
not used
DC 24 V Input ( ⁄ 19" analyzer)
1
2
Pin 1
Signal
9 Input 2 high (+)
Pin no.
8 Input 2 low (-)
7 Input 1 low (-)
1
6 Input 1 high (+)
2
3
6
Pin 8
other
Ethernet connector
for Modbus
1: ME
2: + 24 V
3: 0 V (⊥)
Signal
TX+
TX-
RX+
RX-
not used
A-17