Mxp_2.5G_10E Mxp_2.5G_10E; Mxp_2.5G_10E_L; Mxp_Mr_10Dme; Mxp_Mr_2.5G - Cisco ONS 15454 Manual

NTP-G179 Installing the Transponder and Muxponder Cards
Step 9
Repeat Steps
Step 10 If an OPT-PRE card (or OPT-AMP-L, OPT-AMP-17-C, OPT-AMP-C, OPT-EDFA-17, OPT-EDFA-24, or
OPT-EDFA-35 card in OPT-PRE card mode) is installed, complete one of the following steps for each
OPT-PRE card based on the Cisco Transport Planner shelf layout. If an OPT-PRE is not installed, you have
completed this procedure.
• If the Cisco Transport Planner shelf layout does not include DCUs, install a patchcord and 4-dB attenuator
• If the shelf layout includes DCUs, complete the "NTP-G31 Install the DWDM Dispersion Compensating
Stop. You have completed this procedure.
NTP-G179 Installing the Transponder and Muxponder Cards
Purpose
Tools/Equipment
Prerequisite Procedures
Required/As Needed
Onsite/Remote
Security Level
Turning Up a Node
22
5 through 8 until all the DWDM cards are installed in the node.
with a tolerance of +/–1 dB between the OPT-PRE or OPT-AMP-L DC TX and RX ports for each
OPT-PRE or OPT-AMP-L card installed in the shelf.
Units" procedure for each side of the shelf that requires a DCU.
This procedure describes how to install the
ONS 15454 transponder and muxponder cards.
TXP_MR_10G, TXP_MR_10E, TXP_MR_10E_C,
TXP_MR_10E_L, TXP_MR_10EX_C,
TXP_MR_2.5G, TXPP_MR_2.5G, 40E-TXP-C,
40ME-TXP-C, MXP_2.5G_10G, MXPP_2.5G_10G,
MXP_2.5G_10E, MXP_2.5G_10E_C,
MXP_2.5G_10E_L, MXP_2.5G_10EX_C,
MXP_MR_2.5G, MXP_MR_10DME_C,
MXP_MR_10DME_L, MXP_MR_10DMEX_C,
40G-MXP-C, 40E-MXP-C, 40ME-MXP-C,
AR_MXP, AR_XP, AR_XPE, 100G-LC-C,
10x10G-LC, CFP-LC, 100G-CK-C, 100G-ME-C,
100ME-CKC, 100GS-CK-LC, 200G-CK-LC, WSE,
GE_XP, 10GE_XP, GE_XPE, 10GE_XPE,
ADM-10G, or OTU2_XP cards (as applicable)
• NTP-G313 Installing and Configuring the TNC,
TNCE, TSC, TSCE, or TNCS/TNCS-O Card
• "NTP-G14 Install DWDM Equipment" in the
Cisco ONS 15454 Hardware Installation Guide
• NTP-G139 Verifying Cisco Transport Planner
Reports and Files
As needed
Onsite
None
Turning Up a Node