Christie DHD600-G User Manual
  1. Manuals
  2. Brands
  3. Christie Manuals
  4. Projector
  5. DHD600-G
  6. User manual

Christie DHD600-G User Manual

G series
Hide thumbs Also See for DHD600-G:
Table of Contents

Advertisement

Quick Links

G Series
DWX600-G/DHD600-G/DWU600-G
U S E R M A N U A L
020-000648-01

Advertisement

Table of Contents
loading

Related Manuals for Christie DHD600-G

Summary of Contents for Christie DHD600-G

  • Page 1 G Series DWX600-G/DHD600-G/DWU600-G U S E R M A N U A L 020-000648-01...
  • Page 2 Addendum The CD included with this printed manual contains an electronic copy in English. Please read all instructions before using or servicing this product. Le DC fourni avec ce manuel imprimé contient une copie électronique en français. S'il vous plaît lire toutes les instructions avant d'utiliser ou de réparer ce produit.
  • Page 3 Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user’s own expense. WARNING! Changes or modifications not expressly approved by Christie could void the user’s authority to operate the product.

  • Page 4: Preventative Maintenance

    Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material.

  • Page 5: Table Of Contents

    4.9.6 Tools ........................4-27 4.9.8 About Page ......................4-28 4.10 Christie Presenter ......................4-29 4.10.1 Connect to the Projector ..................4-29 4.10.2 Install Christie Presenter software ..............4-30 4.10.3 Use Christie Presenter ..................4-31 4.11 Card Reader Operation ....................4-37 4.12 Install the Lamp ......................4-41 5. TROUBLESHOOTING 6.

  • Page 6: Federal Communications Commission (Fcc) Warning ................................................6-10 6.8 Osd Tree

    Table of Contents 6.7 Federal Communications Commission (FCC) Warning ..........6-10 6.8 OSD Tree ........................6-11 6.9 Preset Mode tables .......................6-19 G Series User Manual 020-000648-01 Rev. 3 (02-2014)

  • Page 7: Safety

    Change the lamp when the warning message appears. All installation and maintenance procedures must be performed by a Christie accredited service technician. Keep all combustible material away from the concentrated light beam of the projector.
  • Page 8 Section 1: Safety Always power down the projector and disconnect all power sources before servicing or cleaning. Use a soft cloth moistened with a mild detergent to clean the display housing. Disconnect the power plug from the AC outlet if the product is not being used for an extended period of time.

  • Page 9: Introduction

    Section 2: Introduction INTRODUCTION The product specified in this document is a high brightness, high-resolution video/graphics 1-chip mercury lamp based projector. The projector is available in WXGA, HD and WUXGA resolutions. The projector utilizes Digital Light ® Processing (DLP ) technology from Texas Instruments. It is primarily designed for fixed installation markets.
  • Page 10 Section 2: Introduction Rear View Ind. Part Name Description Receives signals from the IR remote. Keep the signal Rear IR Sensor path unobstructed for uninterrupted communication with the projector. Input/Output (I/O) Connects the projector to external devices. Panel Cooling Air Vents Keep these vents unobstructed to prevent the projector (Exhaust) from overheating.
  • Page 11 Section 2: Introduction Left View LAMP Right View Ind. Part Name Description Lamp Door Use the lamp door to access the lamp module. Displays the status of the projector. They are (from left LED Status Indicators to right): LAMP, STATUS, and PIC MUTE. Built-in Keypad Controls the projector.

  • Page 12: Built-In Keypad

    Section 2: Introduction Built-in Keypad Ind. Key Name Description Power Turn the projector on or off Menu Display menus Confirm a selection Enter Auto Automatically optimize image Lens Adjust the lens vertical or horizontal offset setting Focus Adjust focus Exit Return to previous level or exit menus if at top level Adjust a setting UP or DOWN Arrow Keys...

  • Page 13: Input/Output (I/O) Panel

    Section 2: Introduction Input/Output (I/O) Panel Ind. Connector Name Ind. Connector Name Remote IN Mini USB Remote OUT USB Type A Component IN DisplayPort CVBS HDMI S-Video VGA-IN RS232 VGA OUT Ethernet G Series User Manual 020-000648-01 Rev. 3 (02-2014)

  • Page 14: Remote Control

    Section 2: Introduction Remote Control G Series User Manual 020-000648-01 Rev. 3 (02-2014)
  • Page 15 Section 2: Introduction Ind. Key Name Description Picture Mute Display or blank the video image. Power on Turn projector ON. Gamma Adjust mid-range levels. Bright Adjust amount of light in the image. PIP/PBP Turn PIP/PBP ON/OFF. Size Adjust the PIP/PBP size Number Keys Enter a number, such as a channel, value, etc.

  • Page 16: Led Status Indicators

    Section 2: Introduction LED Status Indicators The LED status indicators are located on the right side of the projector. Each LED is defined below. LAMP LED LED Status Projector State Failed to strike lamp after 5 attempts (strike attempts will stop).
  • Page 17 Section 2: Introduction PICTURE MUTE LED LED Status Projector State Green Picture mute is off – image is displayed Yellow Picture mute is on – image is black G Series User Manual 020-000648-01 Rev. 3 (02-2014)

  • Page 18: Installation

    Section 3: Installation INSTALLATION Connect to Computer Desktop Laptop Ind. Connector Name Ind. Connector Name Ind. Connector Name USB Type B Mini HDMI Cable RS232 Cable Cable USB Type A Cable VGA in Cable DVI Cable DisplayPort Cable VGA out Cable Power Cord NOTE: ™...

  • Page 19: Connect To Video Equipment

    Section 3: Installation Connect to Video Equipment Component video output equipment DVD player Video cassette recorder Ind. Connector Name Ind. Connector Name Ind. Connector Name 3 RCA Component HDMI Cable S-Video Cable Cable Component (YPbPr) 15-pin to 3 RCA VGA to RBG SCART Cable Component/HDTV Adapter...

  • Page 20: Turn The Projector On

    Section 3: Installation Turn the Projector On 1. Ensure that the power cord and signal cable are securely connected. The Power button on the built in keypad is illuminated. 9 10 11 12 13 14 15 16 17 18 19 20 “...

  • Page 21: Adjust The Projector Position

    Section 3: Installation Adjust the Projector Position When you select a position for the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Follow these general guidelines: Position the projector on a flat surface at a right angle to the screen.

  • Page 22: Calculate Lens Offset

    Section 3: Installation Calculate Lens Offset The vertical image offset (shift) ranges for the projector are +/-100% (WXGA/WUXGA) and +/-120% (HD). The horizontal image offset (shift) range for the projector are +/-20% (WXGA/HD/WUXGA). The method for calculating lens offset complies with Industry standards. Example for Vertical lens offset: At 0% offset (or on axis), the center of the image is on the lens center, so that half of the image appears above and half appears below the...
  • Page 23 Section 3: Installation Vertical Image Offset: 100% Offset (WUXGA) Image has been offset 600 pixels above lens center, so the center of the image is now 600 pixels above where the center of the image was at 0% offset (or lens center). The offset is +600/600 * 100% = +100%.
  • Page 24 Section 3: Installation HD Projectors: Vertical Image Offset: 0% Offset (HD) No offset is applied - 0% offset. Half of the image appears above lens center and half of the image appears below lens center. 540 pixels above lens center. Lens center 540 pixels below lens...
  • Page 25 Section 3: Installation Vertical Image Offset: -120% Offset (HD) Image has been offset 648 pixels below lens center, so the image has an offset of -648/540 * 100% = -120% Lens center 648 pixels of shift below lens center. Total of 1296 pixels (648+648) of display...
  • Page 26 Section 3: Installation WXGA Projectors: Vertical Image Offset: 0% Offset (WXGA) No offset is applied - 0% offset. Half of the image appears above lens center and half of the image appears below lens center. 400 pixels above lens center. Lens center 400 pixels below lens...
  • Page 27 Section 3: Installation Vertical Image Offset: -100% Offset (WXGA) Image has been offset 400 pixels below lens center, so the image has an offset of -400/400 * 100% = -100% Lens center 400 pixels of shift below lens center. Total of 800 pixels (400+400) of display are below lens center.

  • Page 28: Removing And Installing The Lens

    Section 3: Installation Removing and Installing the Lens When handling the projector after lens installation, make sure the front lens cap is placed on the lens to protect the lens surface from potential damage. When carrying or moving the projector, do not handle by the lens. This may damage the lens, the chassis or other mechanical parts within the projector.

  • Page 29: Cable Cover Installation

    Section 3: Installation Cable Cover Installation Rotate the cable cover and insert the two guide pins into the guide holes. Press and hold both lower corners of the cable cover while inserting the sheet clips into the projector casing. Guide Pin Guide Hole Hold and Press Here 3-12...

  • Page 30: Operation

    Section 4: Operation OPERATION The projector has multilingual On-Screen Display (OSD) menus that allow you to make image adjustments and change a variety of settings. • Most of the projector controls are accessed from within the projector menu system. There are several groups of related functions, with each group selectable from the Main menu as shown below.

  • Page 31: Size And Position Menu

    Section 4: Operation Size and Position Menu Size Presets Display an image with the detected size, or resize the image by maximizing either the height, width or both, or resize to the maximum size possible while keeping the original aspect ratio. Auto: Display with the detected size.
  • Page 32 Section 4: Operation Pixel Phase Analog RGB Signals only. Adjust pixel phase when the image still shows shimmer or noise after pixel tracking is optimized. Pixel phase can adjust the phase of the pixel-sampling clock relative to the incoming signal. Horz Position Move the image right or left within the area of available pixels.
  • Page 33 Section 4: Operation Off: No Geometric correction is applied to the image. Horz Keystone: Adjust the keystone horizontally and make a more square image. Horizontal keystone is used to correct a keystoned image shape in which the left and right borders of the image are unequal in length, and the top and bottom are slanted to one of the sides.
  • Page 34 Section 4: Operation Pincushion/Barrel: Allow for correction for slight curved distortion from the lens or projection surface. 1080P Ind. WXGA WUXGA 8.3% 8.35% 8.37% 3.98% 3.5% 4.59% 6.4% 6.4% 6.5% 6.4% 6.4% 6.4% 4-Corner: Allow the image to be squeezed to fit an area defined by moving each of the four corners’...
  • Page 35 Section 4: Operation Auto Image Force the projector to reacquire and lock to the input signal. This is useful when signal quality is marginal. “Normal mode” can support all of the 4:3 input sources. “Wide mode” can support all of the 16:9 input source & most of the 4:3 input source.

  • Page 36: Image Settings Menu

    Section 4: Operation Image Settings Menu Brightness Adjust the intensity of the image. Contrast Adjust the degree of difference between the lightest and darkest parts of the picture and change the amount of black and white in the image. Color Space Select a color space that has been specifically tuned for the input signal.
  • Page 37 Section 4: Operation Video Black Level: Analyze the current input image and calculate an offset value which is then added to the analog to digital converter black level value. This ensures optimum black level for each analog source. Detect Film: Control film mode detection and determine whether the original source of the input video was film or video.
  • Page 38 Section 4: Operation Advanced Image Settings Gamma: Select the appropriate gamma from Video, Film, Bright, and CRT. BrilliantColor™: Produce an expanded on-screen color spectrum that delivers enhanced color saturation for bright, true-to-life images. White Peaking: (video source only) Increase the brightness of whites that are near 100%.

  • Page 39: Configuration Menu

    Section 4: Operation Configuration Menu Language Allows you to select an available language for the OSD display, from English, French, German, Italian, Spanish, Chinese(simplified), Japanese, Korean, and Russian. Lens Settings Focus and Zoom: Adjust the focus and zoom the image in or out. Lens Shift: Shift the lens up and down or left and right.
  • Page 40 Section 4: Operation Menu Preferences Menu Horz Position: Change the horizontal position of the OSD. Menu Vert Position: Change the vertical position of the OSD. Show Messages: Display status messages on the screen. Menu Transparency: Change OSD menu background to be transparent. NOTE: ™...
  • Page 41 Section 4: Operation Serial Port Echo: Control whether the serial port echoes characters. Projector Address: Set the projector address (0-9). The projector will respond to IR remotes set either at the same address as the projector or to IR remotes set to address 0. Image Blending Adjust blend widths and settings to left, right, top and/or bottom sides to create a seamless multi-projector stitched image.
  • Page 42 Section 4: Operation Color Matching You may require a unique color gamut (range) for a single projector or application, or you may need to precisely match colors across multiple adjacent displays. Use Color Matching by Meter Adjustment or by Manual Adjustment to define the precise hue of each primary color component (red, green, blue and white).
  • Page 43 Section 4: Operation Manual Adjustment 1. Adjust color slide bars and judge image color by eye or meter. A user- defined color “adjustment” can be applied. 2. Use this submenu if you do not have specific color coordinates in mind and will judge color performance by eye or meter. As for Meter Adjustment, each color control actually defines new x/y coordinates for that color and changes its hue.

  • Page 44: Lamp Menu

    Section 4: Operation Lamp Menu Lamp Mode Select Constant Power, Constant Intensity or ECO mode. When in ECO mode, the projector will adjust to the lowest fan speed and switch the lamp power to the minimum setting. Constant Power Set the value of the lamp power (in Watts). Constant Intensity Set the value for the Constant Intensity to maintain constant brightness.

  • Page 45: Status Menu

    Section 4: Operation Status Menu The read-only Status menu lists a variety of details about the standard and optional components currently detected in the projector. For DHD Models 4-16 G Series User Manual 020-000648-01 Rev. 3 (02-2014)
  • Page 46 Section 4: Operation For DWU Models G Series User Manual 4-17 020-000648-01 Rev. 3 (02-2014)
  • Page 47 Section 4: Operation For DWX Models 4-18 G Series User Manual 020-000648-01 Rev. 3 (02-2014)

  • Page 48: Input Switching & Pip Menu

    Section 4: Operation Input Switching & PIP Menu Main Input From the list of active inputs, select one to be used as the main image. PIP/PBP Input From the list of active inputs, select one to be used as the PIP/PBP. PIP/PBP Enable Toggle between displaying two sources at once (Main and PIP/PBP images) or one source only.
  • Page 49 Section 4: Operation NOTE: ™ PIP/PBP layout and size table as described below. ™ P : indicates primary source region (lighter color). ™ * : Both source regions are the same size. PIP/PBP Size PIP/PBP Layout Small Medium Large PBP, Bigger Left Over-Under, Bigger Upper PBP, Bigger Right Over-Under, Bigger Lower...

  • Page 50: Language Menu

    Section 4: Operation Input Key Use it to list all of the sources or change the sources. Language Menu Allows you to select an available language for the OSD display. Test Pattern Menu Choose the desired internal test pattern to display, or select OFF to turn off a test pattern.

  • Page 51: Web User Interface

    Section 4: Operation Web User Interface 4.9.1 Logging On Open your web browser and type the IP address (in the address bar) assigned to your projector. 1 Select the log in level from the Access type drop-down list 2 Enter the Password in the Password field 3 Select the appropriate language from the Language drop-down list.

  • Page 52: Main Tabbed Page - Status

    Section 4: Operation Control Panel Select main source / PIP source, enable/disable PIP/PBP, change the layout / PIP size, swap, and change the test pattern. Projector Information Panel Check the projector information for power status, Pic mute status, OSD status, IP address and Mac address. Switch Panel Switch the on/off status of power, Pic mute, and OSD.

  • Page 53: Main Tabbed Page - Lens

    Section 4: Operation 4.9.4 Main Tabbed Page – Lens Control the focus, lens shift and zoom adjustments for the lens. 4.9.5 Network 4-24 G Series User Manual 020-000648-01 Rev. 3 (02-2014)
  • Page 54 Network Factory Reset Execute a network factory reset. Network settings will be reset to the following default values: - Projector Name = Christie@ + Serial Number - Show Network Messages = ON - LAN Settings: - Manual - IP Address = 192.168.0.100 - Subnet Mask = 255.255.255.0...
  • Page 55 Section 4: Operation - Enter the IP address range, netmask and default gateway for the wireless LAN. SNMP Panel - The G Series SNMP (Simple Network Management Protocol) interface provides network administrators with a common way to manage their network devices from a single remote location. SNMP allows an administrator to query a number of devices to see their current status/ configuration.

  • Page 56: Tools

    Section 4: Operation 4.9.6 Tools Use the Tools tabbed pages to control “Size & Position”, “Image Settings”, “Configuration”, “Lamp”, “Input Switching & PIP” and “Test Pattern”. 4.9.7 Administrator Page Add or delete a user or change password G Series User Manual 4-27 020-000648-01 Rev.

  • Page 57: About Page

    Section 4: Operation 4.9.8 About Page Version Tab View the main firmware version, network firmware version, projector model name, and projector serial number. License Tab The license information of the computer program is displayed. 4-28 G Series User Manual 020-000648-01 Rev. 3 (02-2014)

  • Page 58: Christie Presenter

    Section 4: Operation 4.10 Christie Presenter The Christie Presenter application allows a remote desktop from a host PC to be displayed on the network display through Ethernet, USB, or wireless transports. It can adapt to different network settings (DHCP, fixed IP, and direct link by USB/Ethernet cable).

  • Page 59: Install Christie Presenter Software

    . Example: “Christie@0111000123”. 4.10.2 Install Christie Presenter software 1. Use a web browser to connect to the projector’s network address (Default address 192.168.1.100) 2. Download and install the Christie Presenter Software 4-30 G Series User Manual 020-000648-01 Rev. 3 (02-2014)

  • Page 60: Use Christie Presenter

    Section 4: Operation 3. Configure the Christie Presenter Software. The name entered is used to identify all computers connected to the projector via the Christie Presenter software via either wired or wireless connections. The Network Display Management -> Device Management tab will show all current connections.
  • Page 61 Section 4: Operation 2. After starting the Christie Presenter application, the main window can been seen (shown below). Icon Description Connect and search network display Stop/start displaying desktop contents to connected network display Select display region Configure Christie Presenter Manage all connected network displays...
  • Page 62 Section 4: Operation If the IP address of the projector is known, enter the IP address and click the "Connect" button. If the IP address is not known, click the "Search" button to search for the projector on the network and select the projector to which you want to connect.
  • Page 63 Section 4: Operation Select display region Once the connection is set up, click the button to select the size of the projection region: FullScreen, FixedSize, or Alterable. FullScreen: The default capture mode turns to Full screen when the program is launched. At that time, if screen capture starts, the image of the whole screen is transferred to a remote network display.
  • Page 64 Section 4: Operation Configure Christie Presenter to configure Christie Presenter for Basic Setting Click the button and Advanced Setting. Basic Setting: Select language, change the region size of fixed size capture mode, and select if notification message popup is allowed.
  • Page 65 Section 4: Operation Manage all connected network displays Click the button to control all the users and all the projectors connector to the same projector. Icon Description Administrator log in. Normal user log in. Device is connected. Device is not connected. The icon shows the current status and display position of the local screen on the network display.

  • Page 66: Card Reader Operation

    Section 4: Operation 4.11 Card Reader Operation There are four operation modes in the Card Reader application: - USB Flash Devices Detection Screen - Thumbnail Display Mode - Images Display Mode - Images Slide Show Mode 1. USB Flash Device Detection Screen: In this mode, the Card Reader application detects any USB flash devices hot-plug events and displays the flash device icon.
  • Page 67 Section 4: Operation The user interface is designed to operate the card reader application with a few keys (Enter/Left/Right/Up/Down). The following buttons are supported in the user interface: Previous: Move the selected item left. (Go to previous page when this is the leftmost item) Next: Move the selected item right.
  • Page 68 Section 4: Operation The following operations are supported in the operation UI. Display: Enter the Image Display Mode. Thumbnail: Enter the Thumbnail Display Mode. SlideShow: Enter the Slide Show Mode. Actual Size: Display in actual size of the image. Best Fit: Display the image in best fit to the screen. EXIFDisp OFF/On: Enable/Disable EXIF information display.
  • Page 69 Section 4: Operation When the image can NOT be displayed due to memory limitation or can NOT support image format, the specific image is displayed on the center of the screen. 4-40 G Series User Manual 020-000648-01 Rev. 3 (02-2014)

  • Page 70: Install The Lamp

    Section 4: Operation 4.12 Install the Lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. "When you see this message, please change the lamp as soon as possible." Make sure the projector has been cooled down for at least 30 minutes before changing the lamp.
  • Page 71 Section 4: Operation Remove the old lamp: Loosen the three captive screws securing the lamp. Remove the lamp module slowly and carefully. Install the new lamp: Replace the lamp with a new one and tighten the three screws. Make sure the lamp is set properly and secure. Close the lamp door: Secure the captive screw.

  • Page 72: Troubleshooting

    Section 5: Troubleshooting TROUBLESHOOTING If you are unable to resolve an issue using the information provided in this section, contact your reseller or service center. Problem Solution No image appears Make sure all the cables and power connections are correctly and securely connected See “Installation”. on-screen Check if the lamp is securely installed.
  • Page 73 Section 5: Troubleshooting Problem Solution Partial, scrolling If you are using a Notebook: or incorrectly Adjust resolution of the computer. displayed image Press the keys listed below for your notebook manufacturer to send signal out from notebook to projector. Example: [Fn]+[F4] Notebook Brand Function Keys Acer...
  • Page 74 Section 5: Troubleshooting Problem Solution Image is out of Make sure both lens caps (front and back) are removed. focus Adjust lens focus to fit. Make sure the projection screen is between the required distance. The image is When you play anamorphic DVD or 16:9 DVD, the stretched when projector will show the best image when the projector displaying 16:9...

  • Page 75: Specifications

    Section 6: Specifications SPECIFICATIONS Inputs Signal Frame Rate Resolution HDMI DisplayPort Component S- video CVBS Type (Hz) ● ● 640x350 ● ● ● 640x400 640x480 ● 640x480 ● ● ● ● 640x480 ● ● ● 640x480 ● ● ● ● 640x480 ●...
  • Page 76 Signal Frame Rate Resolution HDMI DisplayPort Component S- video CVBS Type (Hz) ● 960x600 1024x768 ● ● ● ● 1024x768 ● ● ● ● 1024x768 ● ● ● ● ● 1064x600 ● 1064x600 ● ● 1064x600 ● ● 1064x600 ● 1152x720 ●...
  • Page 77 Section 6: Specifications Signal Frame Rate Resolution HDMI DisplayPort Component S- video CVBS Type (Hz) 1280x960 ● ● ● 1280x960 ● ● ● 1280x960 ● ● ● 1280x1024 ● ● 1280x1024 ● ● ● ● 1280x1024 ● ● ● ● 1280x1024 ●...
  • Page 78 Signal Frame Rate Resolution HDMI DisplayPort Component S- video CVBS Type (Hz) 1728x1080 ● 1864x1050 ● 1864x1050 ● 1920X1080 ● ● 1920X1080 ● ● ● ● ● ● ● 1920X1200RB ● ● ● ● 1920X1200RB ● ● NTSC NTSC (M, 4.43) ●...
  • Page 79 Section 6: Specifications Signal Frame Rate Resolution HDMI DisplayPort Component S- video CVBS Type (Hz) 1080i ● ● ● ● 1080i ● ● ● ● 1080i ● ● ● ● ● ● ● ● 720p ● ● ● ● 720p ●...

  • Page 80: Pip/Pbp Compatibility

    PIP/PBP Compatibility Main D i s p l a y - Type B HDMI DVI-D Component S-Video CVBS RJ45 Type A Port PIP/PBP (mini) ● ● ● ● ● ● HDMI ● ● ● ● ● DVI-D ● ● ● ●...

  • Page 81: Key Features

    (Optional) Wireless desktop display using wireless dongle (optional) SNMP traps and e-mail notifications Single mercury lamp illumination with 465W (DWH600-G/DHD600-G/ DWU600-G) 10-bit image processor electronics with modular design All video formats can be resized to full screen either horizontally or...

  • Page 82: List Of Components

    List of Components This projector comes with all the items shown below. Check to make sure your package is complete. Contact your dealer if anything is missing. IR remote control 003-004468-01 Power cord x 4 UK/Korea/Russia North America Europe Japan DVI to HDMI dongle User manual (CD) NOTE:...

  • Page 83: Regulatory

    Section 6: Specifications REGULATORY Safety CSA C22.2 No. 60950-1 UL 60950-1 IEC 60950-1 EN 60950-1 Electro-Magnetic Compatibility Emissions FCC CFR47, Part 15, Subpart B/ANSI C63.4, Class A – Unintentional Radiators CISPR 22/EN55022 Class A - Information Technology Equipment ICES/NMB003 (A) - Information Technology Equipment Immunity CISPR 24/EN55024 EMC Requirements - Information Technology Equipment...

  • Page 84: Federal Communications Commission (Fcc) Warning

    Federal Communications Commission (FCC) Warning WARNING A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded signal cables to connect I/O devices to this equipment.

  • Page 85: Osd Tree

    Section 6: Specifications OSD Tree Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default Auto Native Letterbox Auto Size Presets Full Size Full Width Full Height Custom Overscan Zoom By source set Crop Pixel Track 0 - 100...
  • Page 86 Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default Bottom Left Horz 0-140 adjust. Bottom Left Vert 0-80 adjust. Curve 4-Corner Bottom Right 0-140 Horz adjust. Bottom Right 0-80 Vert adjust. Rotation 0-16 Top Left Horz 0-140...
  • Page 87 Section 6: Specifications Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default Presentation Video Bright Whiteboard Picture Settings By source set Blackboard Beige Wall Real DICOM SIM Save to User User DynamicBlack command Image Freeze Off / On...
  • Page 88 Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default 0.5 W Mode Communication Standby Mode mode Communication Mode AC Power On off/on Never 5 Mins 10 Mins Auto shutdown 15 Mins Never Power Management 20 Mins 25 Mins...
  • Page 89 Section 6: Specifications Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default 0… ½ Output Height(Pixel) 0… ½ Output Bottom Height Overlap 0… ½ Output Left Width 0… ½ Output Right Image Blending Width Blending Area 0-2000...
  • Page 90 Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default Red Part of White 0 - 1000 1000 Green Part of 0 - 1000 1000 Manual White Color Matching Adjustment Blue Part of White 0 - 1000 1000 Reset to Default...
  • Page 91 Section 6: Specifications Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default Constant Power/ Constant Constant Lamp mode Intensity/Eco Power mode Constant Power 360 – 465 Constant Intensity 0 - 10 Lamp Hours Lamp Total Hours All Lamp Info...
  • Page 92 Key number 4 Component Key number 5 Source Hot-Key S-Video Key number 6 Composite Key number 7 Key number 8 Christie Presenter Card Reader Key number 9 Mini USB Key number 0 Change Sources Input key List all Sources Auto Source...

  • Page 93: Preset Mode Tables

    Section 6: Specifications Preset Mode tables A30H-6SW(RYGCWB) CW Presentation Whiteboard Blackboard Beige Wall Descrption Bright Mode Video Mode Dicom Mode Mode Mode Mode Mode Syt. Mode Number Waveform no ColorTemp(default) BRIGHT WARM WARM WARM WARM COOL WARM Bright Warmes Warm Cool Gamma BRIGHT...
  • Page 94 Default Bright- Con- Default Bright- Con- SIGNAL IMAGE Mode IMAGE Mode Mode ness trast Mode ness trast Presentation Presentation Mode Mode Video Mode Video Mode Bright Mode Bright Mode Whiteboard Whiteboard Mode Mode Video Video Composite NTSC Mode Mode Blackboard Blackboard Mode Mode...
  • Page 96 Corporate offi ces Worldwide offi ces USA – Cypress Australia Eastern Europe and India Singapore ph: 714-236-8610 ph: +61 (0) 7 3624 4888 Russian Federation ph: +91 (080) 6708 9999 ph: +65 6877-8737 ph: +36 (0) 1 47 48 100 Canada –...

This manual is also suitable for:

Dwx600-gDwu600-g

Table of Contents