GE Lullaby Warmer Maintenance And Service Manual page 14

5.7 CONNECTING THE POWER CORD ---------------------------------------------------------- 49
5.8 MOUNTING THE ACCESSORIES ------------------------------------------------------------- 49
5.8.1 Mounting the IV pole -------------------------------------------------------------------- 50
5.8.2 Mounting the Monitor /Instrument Tray ----------------------------------------------- 51
5.8.3 Mounting the Utility Pole ---------------------------------------------------------------- 51
5.8.4 Mounting the Cylinder Holder and the Cylinder -------------------------------------- 52
5.8.5 Mounting the Drawer Assembly -------------------------------------------------------- 53
5.8.6 Mounting the Chest Tube Drainage Hanger ------------------------------------------ 54
5.8.7 Mounting the Tubing Management Arm ---------------------------------------------- 54
5.8.8 Mounting the Utility Post (3.5") --------------------------------------------------------- 55
5.8.9 Mounting the Basket Assembly -------------------------------------------------------- 55
5.8.10 Mounting the Resuscitation Bag Clip -------------------------------------------------- 55
5.8.11 Mounting the Retaining Clip ------------------------------------------------------------ 56
5.8.12 Assembling the slotted Bedside Panel ------------------------------------------------- 56
5.9 CHECKOUT PROCEDURES ------------------------------------------------------------------- 56
5.10 REPACKING THE WARMER WITHOUT SKD FOR LOCAL TRANSPORT --------------------- 57
CHAPTER 6 SYSTEM DISMANTLING PROCEDURE --------------------------------------- 58
6.1 DISMANTLING THE ACCESSORIES ---------------------------------------------------------- 58
6.2 DISMANTLING THE BASE AND BED --------------------------------------------------------- 58
6.3 DISMANTLING THE HOOD ASSEMBLY ------------------------------------------------------ 59
6.4 DISMANTLING THE PILLAR TO LEG ASSEMBLY -------------------------------------------- 60
CHAPTER 7 FIELD REPLACEABLE UNIT (FRU) REPLACEMENT PROCEDURES -------- 61
7.1 REPLACING THE PARTS OF THE LULLABY
7.1.1 Replacing the Hood Exterior (FRU Kit No: 2043936-001) ----------------------------- 61
7.1.2 Replacing the extrusions ---------------------------------------------------------------- 62
7.1.3 Replacing the hood spacer, hood top plate and observation lamp plate ---------- 63
7.1.4 Replacing the Front Bracket ------------------------------------------------------------ 64
7.1.5 Replacing the Front and Rear Covers -------------------------------------------------- 65
7.1.6 Replacing the PCB Wire Assembly (PWA) (FRU Kit No. 2043951-001) --------------- 66
7.1.7 Replacing the Hood Support Plate and Rear Bracket (FRU KIT: 2043937-001) ----- 71
7.1.8 Replacing the Heater Assembly (FRU Kit No. 2043938-001) and Heater Cables (Part
of FRU Kit No. 2043950-001 ------------------------------------------------------------------------ 75
7.1.9 Replacing the Heater Assembly (FRU Kit No. 2062274-001 for 230V, 2056782-
001for 115V and 2061250-001 for 100V ) and Heater Cables (Part of FRU Kit No. 2062276-
001 for 230V, 2062276-001 for 115V and 2062276-001 for 100V) ----------------------------- 79
7.1.10 Replacing the Heater Tube (FRU Kit No. 2045962-001) ------------------------------ 82
7.1.11 Replacing the Observation Lamp (FRU Kit No. 2043939-001) ----------------------- 83
7.1.12 Replacing the LED Observation Lamp (FRU Kit No. 2062275-001) ------------------ 84
7.1.13 Replacing the UI Sticker (Overlay Display), Probe
85
7.1.14 Replacing the Bed tilt Mechanism (FRU Kit No. 2043943-001) ---------------------- 86
7.1.15 Replacing the Bed Base Assembly (FRU Kit No. 2043949-001) ---------------------- 91
xiv 2042376-001 Rev G ©2012 General Electric Company. All rights reserved. Lullaby
WARMER ------------------------------------ 61
TM
protective cover and switches
Warmer
TM