Table of Contents
Advertisement
C C h h a a p p t t e e r r 6 6 O O p p e e r r a a t t i i o o n n
This chapter contains information on how to use the Eaton 9355 UPS, including front panel operation, UPS
startup and shutdown, and configuring the UPS for Extended Battery Modules (EBMs).
To remove the existing power cords:
6 6 . . 1 1
C C o o n n t t r r o o l l P P a a n n e e l l F F u u n n c c t t i i o o n n s s
1.
If the UPS and internal batteries are already installed, continue to
The UPS has a four-button graphical LCD with backlight. It provides useful information about the UPS itself,
Step 2. If the UPS and internal batteries are not installed, continue
load status, events, measurements, and settings (see
to Step 15.
Figure 45. Eaton 9355 UPS Control Panel
2.
You MUST shut down the UPS before replacing the cord assembly.
Continue to Step 3 to shut down a standalone UPS.
For parallel shutdown procedures, refer to the Eaton BladeUPS
(12 kVA) User's Guide and then continue to Step 11.
3.
Switch the load connector circuit breaker to the OFF (O) position
(see Figure 2).
NOTE The load connector breaker controls the load connector only, not the output power.
OPERATION
OPERATION
OPERATION
4.
Press any button on the front panel display to activate the menu
options. Select TURN UPS ON/OFF, TURN UPS OFF, and press the
button.
The following table shows the indicator status and description.
5.
Confirm the selection. Press and hold the
Indicator
Indicator
Indicator
seconds, until the UPS stops beeping.
Indicator
The output relays open, the UPS transfers to Standby mode, and
Green
Green
the
indicator turns off.
Green
Green
6.
Switch the UPS battery circuit breaker to the OFF (O) position.
7.
If optional EBMs are installed, switch all EBM battery circuit
breakers to the OFF (O) position.
Disconnect the EBM cable from the UPS extended battery
Yellow
Yellow
Yellow
Yellow
connector.
8.
Switch the UPS input circuit breaker to the OFF (O) position.
Yellow
Yellow
Yellow
Yellow
9.
Switch off utility power where the UPS is connected.
10. Unplug the power cords.
Red
Red
Red
Red
6 6 . . 1 1 . . 1 1 C C h h a a n n g g i i n n g g t t h h e e L L a a n n g g u u a a g g e e
Press and hold the first button on the left for approximately five seconds to select the language menu. This
Eaton BladeUPS Cord Kit Instructions
action is possible from any LCD menu screen.
6 6 . . 1 1 . . 2 2 D D i i s s p p l l a a y y F F u u n n c c t t i i o o n n s s
As the default or after 15 minutes of inactivity, the LCD displays the selectable startup screen. The default is
the Eaton logo and can be changed to the Mimic screen in the User Settings menu.
CORD KIT INSTRUCTIONS
Control Buttons
for the LCD Menu Options
The following table shows the indicator status and description.
The following table shows the indicator status and description.
The following table shows the indicator status and description.
button for three
Status
Description
Status
Description
Status
Description
Description
Status
On
The UPS is operating normally.
On
The UPS is operating normally.
On
The UPS is operating normally.
On
The UPS is operating normally.
S The UPS is starting up or is shut down and waiting for power to return.
Flashing
Flashing
S The UPS is starting up or is shut down and waiting for power to return.
S The UPS is starting up or is shut down and waiting for power to return.
Flashing
S A new information message is active.
S A new information message is active.
S A new information message is active.
Flashing
A new information message is active.
S Bypass is not available.
S Bypass is not available.
S Bypass is not available.
Off
The UPS is turned off and will not turn on automatically.
Off
The UPS is turned off and will not turn on automatically.
Off
The UPS is turned off and will not turn on automatically.
Off
The UPS is turned off and will not turn on automatically.
On
The UPS is in Battery mode.
On
The UPS is in Battery mode.
On
The UPS is in Battery mode.
On
The UPS is in Battery mode.
On
The UPS is in Bypass mode.
On
The UPS is in Bypass mode.
On
The UPS is in Bypass mode.
On
The UPS is in Bypass mode.
On
The UPS has an active alarm.
On
The UPS has an active alarm.
On
The UPS has an active alarm.
On
The UPS has an active alarm.
Flashing
There is a new UPS alarm condition. See "Troubleshooting" on page 67 for
Flashing
There is a new UPS alarm condition. See
Flashing
There is a new UPS alarm condition. See "Troubleshooting" on page 67 for
Flashing
There is a new UPS alarm condition. See "Troubleshooting" on page 67 for
additional information.
additional information.
information.
additional information.
Changing the Language
Changing the Language
Changing the Language
Press and hold the first button on the left for approximately five seconds
Press and hold the first button on the left for approximately five seconds
S
Press and hold the first button on the left for approximately five seconds
164201721 Rev 2 Draft 13-APR-2010
to select the language menu. This action is possible from any LCD menu
to select the language menu. This action is possible from any LCD menu
to select the language menu. This action is possible from any LCD menu
screen.
screen.
screen.
Display Functions
Display Functions
Display Functions
As the default or after 15 minutes of inactivity, the LCD displays the
As the default or after 15 minutes of inactivity, the LCD displays the
As the default or after 15 minutes of inactivity, the LCD displays the
selectable startup screen. The default is the Eaton logo and can be
selectable startup screen. The default is the Eaton logo and can be
selectable startup screen. The default is the Eaton logo and can be
changed to the Mimic screen in the User Settings menu.
changed to the Mimic screen in the User Settings menu.
changed to the Mimic screen in the User Settings menu.
Eaton 9355 Parallel UPS (10/15 kVA) User's Guide 164201601—Rev E0
The backlit LCD automatically dims after a long period of inactivity. Press
The backlit LCD automatically dims after a long period of inactivity. Press
The backlit LCD automatically dims after a long period of inactivity. Press
any button to restore the screen.
any button to restore the screen.
any button to restore the screen.
Use the two middle buttons ( and ) to scroll through the menu
Use the two middle buttons ( and ) to scroll through the menu
Use the two middle buttons ( and ) to scroll through the menu
Figure
45).
Power On Indicator (green)
On Battery Indicator (yellow)
Bypass Indicator (yellow)
Alarm Indicator (red)
Chapter 7 Troubleshooting
5
for additional
49
Advertisement
Table of Contents
