JUKI AB-1351 Instruction Manual page 93

no.
shape no. 6: 3rd sewing position correction in
lateral direction of clamp
For shape No. 6, ths swtch s used to correct the
lateral poston of the belt loop clamp at the 3rd sewng
poston.
Carry out the correcton f the belt loop poston devates
from the sewng poston.
+ : Belt loop s moved to the rght wth respect to the
sewng poston.
- : Belt loop s moved to the left wth respect to the
sewng poston.
shape nos. 5, 7, 12: Belt loop rolling position
correction in terms of lateral direction of clamp
For shape Nos. 5, 7 and 12, ths s the amount of lateral
travel of the belt loop clamp before removng the fork
from the belt loop.
shape nos. 7, 9: loosening amount after releasing
rod has moved, in terms of longitudinal direction of
clamp
For shape Nos. 7 and 9, t s the amount by whch the
garment-body tenson s reduced by movng the belt
loop clamp forward after havng moved t to far sde to
allow the belt loop releasng rod can be nserted.
shape no. 6: loosening amount between the 2nd
and 3rd sewing positions
Ths s the loosenng amount of the garment body
tenson durng the travel to the 3rd sewng poston by
operatng the garment body feed before the travel to the
3rd sewng poston.
+ : To ncrease the belt loop loosenng amount
- : To decrease the belt loop loosenng amount
shape nos. 7, 9: speed limitation of travel to lower
bartacking position
For shape Nos. 7 and 9, the speed of the clamp when t
travels to the 2nd sewng poston can be lmted.
shape nos. 3, 4, 5, 10, 11, 12: correction of
longitudinal position of belt loop clamp at 2nd
sewing position
For shape Nos. 3, 4, 5, 10, 11 and 12, ths swtch s
used to correct the longtudnal poston of the belt loop
clamp when lowerng the work clamp of the machne
head at the 2nd sewng poston.
shape nos. 4, 5: correction of amount of moving
belt loop clamp to far side during 2nd sewing
For shape Nos. 4 and 5, ths swtch s used to correct
the amount of movng the belt loop clamp to far sde
durng 2nd sewng.
Manual pedal use: Amount of moving garment body feed
backward after garment body presser has come down
In the case the manual pedal has been programmed
by the devce settng data so that the front and rear
garment body pressers are drven separately and the
garment body feed travel s enabled after the garment
body presser has come down, ths s the amount of
travel of the garment body feed after the garment body
presser has come down.
→ Refer to
detals of the devce settng data changng procedure.
* : Data marked with an asterisk (*) are not displayed on the sewing data list screen. they are displayed,
however, from the data entry screen.
: Data in a gray box are not displayed in the standard state. to display them, refer to the Engineer's Manual.
Item
"@-2-29. How to set the device", p.98
– 88 –
Input range/
selection range
-3.0 to 3.0
(mm)
-6.0 to 6.0
(mm)
0 to 13.0
(mm)
0 to 40.0
(mm)
1000 to 4000
(pps)
-3.0 to 3.0
(mm)
-20.0 to 20.0
(mm)
0 to 20.0
(mm)
for
Initial
value
0
(mm)
0
(mm)
0
(mm)
25.0
(mm)
4000
(pps)
0
(mm)
0
(mm)
10.0
(mm)