Page 1
Version Translation of the original instruction manual Instruction manual Industrial PCs OPC8017 OPC8024 / OPD8017 OPD8024 Updated 2019-07-17...
German instruction manual. 2.1.2 Limitation of liability ads-tec GmbH shall not be liable for personal injury, property damage or damage caused to the device as well as consequential damage that is/was the result of non-compliance with this instruction manual, improper use of the device, repairs and other actions on the device by unqualified electricians and electricians not certified by ADS-TEC, or that is/was the result of using unapproved replacement parts.
OPC8017 OPC8024 / OPD8017 OPD8024 2.1.3 Manufacturer and contact details The manufacturer of the product is ads-tec GmbH. The company is referred to in the following as ADS-TEC. ads-tec GmbH Heinrich-Hertz-Str.1 72622 Nürtingen Germany Phone: +49 7022 2522-0 Fax: +49 7022 2522-400 Email: mailbox@ads-tec.de...
StoraXe® and Big-LinX® are registered trademarks of ADS-TEC. All other used third-party trademarks are hereby acknowledged. In the case of trademark infringement, ADS-TEC reserves the right to exercise all rights. 2.1.8 Copyright This instruction manual is protected by copyright. For the authorised user, simple usage rights are granted within the scope of the intent of the contract.
A corresponding EU conformity declaration is available for competent authorities at the manufacturer and can be viewed upon request. The EU conformity declaration can be requested on our website www.ads-tec.de and downloaded in the Download area. The product also complies with the following UL standards:...
The device can be put into operation and used under the following environmental conditions. Failure to observe any one of these conditions will invalidate the warranty of the device. ADS-TEC cannot be held liable for any damages arising from improper use and handling.
In the case of improper use, ADS-TEC shall not accept responsibility or liability for injury or damage that is directly or indirectly attributable to the handling of the device.
ATTENTION Damage to the electronics! If a device with data drive is not installed vertically, the electronics may suffer damage. Install devices with data drive vertically only. Deviations must be arranged with ADS-TEC. ATTENTION Mechanical damage! If the device is not mounted correctly, IP65 protection will not be provided.
Page 28
You can integrate the device in an Ethernet network which supports 1 Gbit/s. For this purpose, use the 1Gbit RJ45 LAN ports. If required, the necessary drivers can be downloaded at www.ads-tec.de. The specifications for the network topology must be observed.
Page 41
Recommendation for use: Insofar as they are specified in the scope of delivery or in the replacement parts list, only connectors and cables offered by ADS-TEC are to be used for commissioning and during operation. All other connectors and cables which you use for commissioning and during operation must have been approved.
OPC8017 OPC8024 / OPD8017 OPD8024 The necessary driver software is already integrated in the respective operating system. If you need other drivers, you can download them at http://www.ads-tec.de in the Download area. Figure 22: Touch surface 8.3 Component replacement...
OPC8017 OPC8024 / OPD8017 OPD8024 8.3.2 Replacing mass storage device On the OPC8017/OPC8024, there may be a mass storage device in the service slot. Removing mass storage device 1. Remove the cover plate. To do so, undo the fastening screw (1) (PH1 cross-tip screwdriver).
Insofar as they are specified in the scope of delivery or in the replacement parts list, only connectors and cables offered by ADS-TEC are to be used for commissioning and during operation. All other connectors and cables which you use for commissioning and during operation must have been approved.
DV-MMXADAPT xxx-yy. Several versions of DV-MMXADAPT xxx-yy are available, the differences are indicated by xxx-yy. Examples for this are: Front foils and keys can be customized, if this is done at ADS-TEC, this changes xxx-yy in the article number. Details are described in chapter 4.3.2.
Windows Embedded 8.1 Industry Pro (64 bit) Windows 10 IoT (64 bit) Protection class IP65 at front, IP20 at rear (not verified by UL, tested by ADS-TEC) Operating 0 °C to +50 °C 0 °C to +45 °C 0 °C to +50 °C 0 °C to +45 °C...
Because ADS-TEC products are also used by partner companies, these devices may have customised configurations. Should any questions arise with regard to such specific configurations and software installations, please contact the system supplier in question as ads-tec will not be able to answer such questions.