Related Manuals for ADS-tec OPC8008
Summary of Contents for ADS-tec OPC8008
- Page 1 Version Translation of the original instruction manual Instruction manual Industrial PCs OPC8000 series Effective as of: 02.02.2017...
-
Page 2: Table Of Contents
Safety notices prior to beginning installation 4.11 Order of installation (OPC8008) 4.12 Order of installation (OPC8013-8022) Commissioning ..........................35 Available Interfaces (OPC8008) Available interfaces (OPC8013-8022) Cable installation Order of steps during commissioning © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... - Page 3 Replacing the lithium battery (OPC8000 series) 12.4 Replacing the HDD (hard disk) (OPC8013-8022) 12.5 Replacing the fan (OPC8013-8022) 12.6 Replacing the working memory (RAM) (OPC8013-8022) 12.7 Replacing the mSATA modules (OPC8000 series) © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
-
Page 4: Notes
German instruction manual. 1.2 Limitation of liability ADS-TEC GmbH shall not be liable for personal injury, property damage or damage caused to the device as well as consequential damage that is/was the result of non-compliance with this... -
Page 5: Relevant Device Documentation
Contains information for installation, commissioning and operation of the device along with technical data of the device hardware. Website You can download drivers, software, user manuals, leaflets and flyers about the product from our website www.ads-tec.de. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 6: Safety Instructions
Indicates a possible danger. If not avoided, light or minor injuries could result. ATTENTION Indicates a possibly damaging situation. If not avoided, the system or something in its surroundings could be damaged. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 7: Symbols
StoraXe® and Big-LinX® are registered trademarks of ADS-TEC. All other third-party trademarks used are hereby acknowledged. In the case of infringement of trademark rights, ADS-TEC reserves the right to exercise all rights. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 8: Copyright
ADS-TEC. In the case of copyright infringement, ADS-TEC reserves the right to exercise all rights. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 9: Environmental Conditions
2.8 Environmental conditions The device can be put into operation and used under the following conditions. Failure to observe any one of these conditions will invalidate the warranty. ADS-TEC cannot be held liable for any damages arising from improper use and handling. -
Page 10: Standards
1 x device 1 x 3-pole lead-through connector from Phoenix Contact; 3-pole screwable 3.81 OPC7 (already plugged into device socket) QuickStartGuide Optional scope of delivery: Operating system © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 11: Device Features
OPC8000 series 2.11 Device features Proven many times over in rough environments, Panel PCs from ADS-TEC create clarity and precision in a new form. Optimised in every detail - with multi-touch operation and rear service access for simple and safe replacement of all components. In wide-screen format in four different sizes, reduced to the essential without compromise, powerful and with long-term availability. - Page 12 OPC8000 series Rear side Fig. 2: Description Service slot Tensioners for installation purposes © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
- Page 13 OPC8000 series Rear side Fig. 3: Description Tensioners for installation purposes Service slot © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
-
Page 14: Operating And Safety Instructions
(e.g. Sidolin) with low alcohol content. ATTENTION To prevent damage to the device, all cable lines (power supply, interface cables) must be only be connected while the device is switched off. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 15: Operating Location
Ensure that it is secured against being started up accidentally. 3.3 Warranty / repairs During the device warranty period, any repairs must only be performed by the manufacturer or by service personnel that has been authorised by the manufacturer. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 16: Intended Use
In the case of improper use, ADS-TEC shall not accept responsibility or liability for injury or damage that is directly or indirectly attributable to the handling of the device. -
Page 17: Treatment And Disposal Of Lithium Batteries
The used lithium battery should be disposed of in accordance with local legal regulations. The battery type to be used is: Lithium battery 1/2AA 3V (e.g. ADS-TEC part number: DZ-SONS-04100-0) The used lithium battery should be disposed of in accordance with local legal regulations. -
Page 18: Safety Instructions
Recommendation for use: Always adhere to the safety measures applicable when handling components at risk of being damaged by electrostatic discharges. The provisions of DIN EN 61340-5-1 / DIN EN 61340-5-2 apply © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 19: Installation
When selecting the enclosure for integration, the total power dissipation of the system including installed PCBs must be taken into account. The housing must be dimensioned so that the max. permissible ambient temperature is not exceeded. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 20: External Device Dimensions Opc8008
OPC8000 series 4.2 External device dimensions OPC8008 Abb. 4: © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 21: External Device Dimensions Opc8008
OPC8000 series 4.3 External device dimensions OPC8008 © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 22: External Device Dimensions Opc8013
OPC8000 series 4.4 External device dimensions OPC8013 Fig. 5: © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 23: Installation Layout Opc8013
OPC8000 series 4.5 Installation layout OPC8013 © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 24: External Device Dimensions Opc8015
OPC8000 series 4.6 External device dimensions OPC8015 Fig. 6: © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 25: Installation Layout Opc8015
OPC8000 series 4.7 Installation layout OPC8015 © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 26: External Device Dimensions Opc8022
OPC8000 series 4.8 External device dimensions OPC8022 © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 27: Installation Layout Opc8022
OPC8000 series Fig. 7: 4.9 Installation layout OPC8022 © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 28: Safety Notices Prior To Beginning Installation
Non-compliance may result in damage to the device! ATTENTION The grub screws must not be screwed in while folded in! Non-compliance may result in damage to the touch-screen of the device! © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 29: Order Of Installation (Opc8008)
Before the device can be integrated in the panel, the tensioner fixing screws must be loosened until the tensioners open. (Item 1 - item 2). Information: Tensioners can be opened by using an Allen key of 3 mm size. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... - Page 30 2) Now, position the device inside the installation recess. ATTENTION In order to position the device correctly, the opened tensioners should be held back by hand while inserting the device in the installation recess. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
- Page 31 OPC8000 series Fasten the tensioner screws with 0.25 NM until once the device is installed in the recess. (Item 3) © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
-
Page 32: Order Of Installation (Opc8013-8022)
/ power supply connection. In the event of additional earthing on the earthing screw, use wire cross section with at least 2.5 mm². © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... - Page 33 The fixing screws for the tensioners must be screwed in. The screws can be unscrewed with a size TX8 screwdriver. The device is placed in the created recess. The tensioners snap back. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
- Page 34 The device must be carefully pushed into the cabinet. Then the tensioners snap forward again. The device is now secured in the installation recess. The tensioners must be fastened with 0,25 NM. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
-
Page 35: Commissioning
The shielding of a data cable must always be connected with the connector housing (EMC). For embedded operating systems, the interfaces must be explicitly enabled and the necessary drivers installed in order to use them. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 36: Available Interfaces (Opc8008)
OPC8000 series 5.1 Available Interfaces (OPC8008) Abb. 8: Variante 1 Description On-/Off Switch Power Supply 24 V DC 1 x COM-Port 2 x LAN 3 x USB 2.0 © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 37: Available Interfaces (Opc8013-8022)
5 x USB 2.0 3 x LAN Abb. 10: Variante 2 Description On-/Off Switch Power Supply 24 V DC 1 x COM-Port 2 x USB 3.0 2 x USB 2.0 3 x LAN © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 38: Cable Installation
Check the device for hidden damages caused by improper transport, incorrect operation/storage conditions or improper use (e.g., smoke emissions from the device, etc.). If damages are found, immediately shut down the device and protect it against unintentional startup. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 39: Operation
Fn-key again, the Fn-function is disabled. If the soft keyboard is not installed, level 1 of the ABC key has no function. Furthermore, no graphical feedback is provided when changing the display brightness. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 40: Switching-On Function
Intel® Celeron® 2002E 1,50 GHz ̶ Intel® Core™ i5-4400E 2,70 GHz Check in your BIOS or in the System control of the operating system to see which type of processor your mainboard uses. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 41: Activating The Front Keys For The Boot Menu And Bios
SHIFT key for activating the second keyboard level. The key has to be pressed shortly and is activated permanently (it can be recognized via the blue highlighted keys). By pressing the Fn-key again, the Fn-function is disabled. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 42: Soft Keyboard
The Shift, Alt and Ctrl special keys must always be pressed first. Due to differences in programming of a large variety of software © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 43: Touch Screen
Min-/Max value of brightness has been reached Pos : 25 /D atentec hni k/Schnitts tell en/Sc hnitts tell eneinstellung/Sc hni ttstelleneins tell ung für VMT-Serie / PLC 500 @ 0\mod_1158916296612_6.doc @ 517 @ © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 44: Interfaces
30 /D atentechni k/Sc hnittstellen/PS2/Kombi Buchs e für VMT 60xx @ 2\mod_1268840073235_6.doc @ 7482 @ Pos : 31 /D atentec hni k/Schnitts tell en/Netz werkansc hlus s RJ 45/Netz wer kansc hluss RJ 45 für VMT 60xx @ 2 \mod_1260451135970_6.doc @ 6856 @ © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 45: Network Connection (Rj45)
Pos : 33 /D atentec hni k/Schnitts tell en/Seriell e Schnitts tell e C OM RS232/Serielle Sc hnitts tell e C OM (RS232) für VMT 60xx @ 1 \mod_1246373571514_6.doc @ 5876 @ © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 46: Serial Interface Com (Rs232)
The serial interface is used for digital data transmission. The RS232 interface can be connected by using a commercially available 9-pin SUB-D cable. PIN number Signal name Information: This interface is not electrically isolated. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 47: Drives
Pos : 36 /D atentec hni k/Softwar e / Trei ber Install ati on/I nstallati on des Betriebss ystems\mod_1263211380903_6.doc @ 6940 @ © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 48: Software
9.1 Configuration Center If a pre-installed operating system is available on your device, ADS-TEC provides software modules. These software modules are specifically designed for each device and can be accessed in the Configuration Center. -
Page 49: Technical Details
3 x USB 2.0 5 x USB 2.0 or **** 2 x USB 2.0 & 2 x USB 3.0 Network 2 x Ethernet (10/ 3 x Ethernet (10/100/1000Mbit) RJ 45 100/1000Mbit) RJ 45 © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... - Page 50 * Only for versions with mSATA-Form factor SSD with extended temperature range ** Shared memory *** Tolerance + / - 1 mm **** only with processors of the 4th generation (i5-2002E, Celeron 4400E) © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
-
Page 51: Service & Support
ADS-TEC will not be able to answer such questions. ADS-TEC does not provide support services for any device that was not purchased directly from ADS-TEC. In this case, maintenance and support is provided by the partner company. -
Page 52: Component Replacement
12.1 Opening the service slot (OPC8008) Remove the four screws for the service slot on the rear of the device. Fig. 13: © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... - Page 53 OPC8000 series Fig. 14: By removing the service slot cover, it is possible to replace the following components. Lithium battery mSATA connection © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
-
Page 54: Opening The Service Slot (Opc8013-8022)
Remove the four screws for the service slot on the rear of the device. The screws can be removed with a size Tx 10 screwdriver. The rear cover can be tilted forward and removed using the groove on the top side of the service slot. Fig. 15: © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... - Page 55 OPC8000 series Fig. 16: By removing the service slot cover, it is possible to replace the following components. Lithium battery mSATA connection © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...
-
Page 56: Replacing The Lithium Battery (Opc8000 Series)
The lithium battery can now be removed. It may only be replaced with a battery of the same type. The type of battery to be used is: Lithium battery 1/2AA 3V (e.g., ADS-TEC part number: DZ-SONS-04100-0) Ensure the correct polarity when inserting the battery... -
Page 57: Replacing The Hdd (Hard Disk) (Opc8013-8022)
The extraction aid provided on the HDD should be used for removing the HDD. Carefully pull out the HDD. Installation The HDD must be carefully inserted into the slot and should noticeably engage. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 58: Replacing The Fan (Opc8013-8022)
Use a size Tx 10 screwdriver to remove the fan screws. The fan can then be lifted out and replaced with a new one. Installation Screw the previously removed screws back in and plug the fan cable in again. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 59: Replacing The Working Memory (Ram) (Opc8013-8022)
The RAM memory is released by carefully pulling apart the retaining clips (1+2). It can now be replaced with new RAM memory. Installation Insert the new RAM memory in the designated slot and push the RAM memory to the back until the retaining clips engage. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... -
Page 60: Replacing The Msata Modules (Opc8000 Series)
For the devices OPC8013-8022, the HDD (hard disk) must be removed before the SSD Flash Modules can be installed or replaced. Remove the HDD (OPC8013-8022) Remove the screw(s) of the spacer bolt by using a Tx10 screw driver. © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen... - Page 61 OPC8000 series Mounting (OPC8000 Serie) 1 Mainboard 2 plastic disc 3 plastic distance holder 4 mSATA Card 5 plastic disc © ADS-TEC GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen...