Parameter Changing Methods And Classification; 9-1) Parameter Numbers Related To General Sewing (Group A) - SunStar SPS/E-BH6100 User Manual

9 9

Parameter Changing Methods and Classification

9-1) Parameter numbers related to general sewing (Group A)

★ Turn on the power, while pressing the left key and the presser UP/DOWN key at the same time, and then '1' flickers on the screen. Press
ENTER, and the screen shows the item list of parameter Group A. Use the DOWN key to select the desired number and press ENTER.
Then, the parameter setting screen appears. Use the + and - key to change the parameter values. Press ENTER to save the changed values.
No Function and Description
A-01 Maximum sewing speed
Set the sewing starting speed for 1st~5th
A-02
needle (set the soft start)
A-03
Set the X-Y transfer position
A-04
Set the thread trimming speed
A-05
Set the UP/DOWN production counter
A-06
Set the production counter
A-07
Set the down mode
A-08
Origin check mode setting
A-09
Origin check counter setting
A-10 Set the automatic check of rocking point
When start sewing, thread tension solenoid
A-11
on time setting
When sewing is stopped, set the value of thread tension
A-12
(Use the upper thread holder)
Enable/Disable of upper thread nipper
A-13
device
A-14
Thread tension solenoid Full-on time setting
A-15
Feeding base position setting
A-16
Deciding the use of the vent_hole pattern
When sewing is stopped, set the value of thread tension
A-17
(Use the upper thread holder)
A-18 AC Off time setting
A-19 Overvoltage check time setting
When power switch is in the "ON" position, set the
A-20
initial value of thread tension
When moving the feed base to the sewing position to set the
A-21
second origin, set the operation of the fabric opening device.
A-22
Hand switch mode setting
Setting the time taken from presser foot
A-23
descent to beginning of sewing
A-24
Feed base speed adjustment (Advance)
A-25
Blade motion method choice (Sensor or Timing)
A-26 Low voltage error check frequency setting
A-27 Set thread breakage check though sewing
A-28 Set thread breakage stich numbers
A-29 Feed base speed control(reverse)
A-30
Delayed time to complete the knife operation
A-31
Set thread breakage stich numbers
Evaluate and set up the angle of separating thread
A-32
from the lower thread during lower thread trimming.
Set up the location of clamp after finish stitching.
A-33
(in case of thread detection and emergent stop)
After finish stitching set up the thread tension ON time
A-34
before upper thread trimming.
After finish stitching set up the thread tension OFF time
A-35
before upper thread trimming.
74
Name of Function Setting Range
m spm 2500 spm
1st needle :100~900
2st needle:100~2700
Slow 3st needle:100~2700
4st needle:100~2700
5st needle:100~2700
F pos -100 ~+100
T spm 200~400 spm
Down Product
CntMd
Up Product
Disable
CntFg
Enable
Buzz & Key
CntDn Key
Buzz
Counter:Origin after countering
completes
M_ORG
Auto:Origin after sewing scompletes
C_ORGv 0 ~ 256
Disable
LIM_S
Enable
SoITM 4~1020ms
N_off 5~100
Disable
NIP_D
Enable
THSOL 4~1020ms
Origin Position
BaseP
Sewing Position
Disable
HOLE
Enable
N_On 10~200
ACOff 4 ~60ms
OverL 4 ~1020ms
ITens 10 ~60
Enabled
OPEN
Disabled
PMode one switch dual switch
PF_TM 4 ~ 1020ms
YFeed 4 ~ 1020ms
KMode Sensor or Timing
UndrL 4 ~ 1020ms
Disable
ThCut
Enable
ThSti 6~30[stitch]
BWspd 1~50[us]
KnfTM 4~1020[ms]
UT_TM 4~1020[ms]
UtAng 1 ~ 180[degree]
ST_PF down / up
On TM 4 ~ 400[ms]
Off TM 4 ~ 400[ms]
Default Unit
2200 spm 100spm
200spm
500spm
1000spm 100spm
1500spm
2500spm
0 1
400 spm 100spm
Up Product
Disable
Buzz & Key
Counter
20 1
Enable
100ms 4ms
30 1
Enable
100ms 4ms
Origin
Position
Disable
150 1
20ms 4ms
20ms 4ms
20 1
Disable
dual switch
100ms 4ms
16us 4us
Sensor
20ms 4ms
Disable
10[stitch] 2[stitch]
15[us] 1[us]
100[ms] 4[ms]
100[ms] 4[ms]
15[degree] 1[degree]
down
600[ms] 4[ms]
100[ms] 4[ms]