Menu Overview - SunStar SPS/E-BH6100 User Manual

7) Menu overview

DATAINFO (Menu)
1. Speed
(Set the Speed)
2. Pattern
(Set the Pattern)
3. Knife(Knife-Related
Settings)
4. E_Comp.(Compensate
the Up bartack part)
5. C_Comp.(Compensate
the Zigzag part)
6. T_Comp.(Compensate
the Slant)
7. Chain(Set the Chain
Sewing)
8. BT_STI(Set the
Back-Tack)
1) The symbol (
2) There are four clamp type options from A to D.
3) For more information on how to set the clamp type, see "6-4) Knife-related Parameter Setting".
Caution
1. Main(Main Speed)
2. Up Bar(Eyelet Speed)
1. Taper 1. Up Bar (Eyelet
(Taper Pattern) Compensation)
2. Zigzag (Straight Line
Compensation)
3. Dn Bar (Taper
Compensation)
1. Up Bar (Eyelet
2. Tack
Compensation)
(Tack Pattern)
2. Zigzag (Straight Line
Compensation)
3. Dn Bar (Tack
Compensation)
1. Up Bar (Eyelet
3. Radial
Compensation)
(Radiation pattern)
2. Zigzag (Straight Line
Compensation)
3. Dn Bar (Tack
Compensation)
1. InSide (Inside)
4. Eyelet (Eyelet
Shape Pattern)
2. OutSide (Outside Compensation)
3. Stitch (Stitch No. Setting)
1. Length(Knife No)
2. L Space(Left Space)
3. R Space(Right Space)
4. KNF POS(Place Motion Space)
5. CP Type (sewing size setting)
1. Rotate(Eyelet Rotation)
2. Radius(Eyelet Radius)
3. X_Comp(X Position Compensation)
4. R_Comp(Adjustment of right side slant width)
5. L_Comp(Adjustment of left side slant width)
1. Rotate(Straight Line Rotation)
2. Length(Straight Line Pitch)
3. Width(Straight Line Width)
1. Taper (Taper Pattern Compensation)
2. Tack (Tack Pattern Compensation)
3. Radial (Radiation pattern reply correct)
1. OnOff(Enable/Disable the Chain Sewing Function)
2. Set_No(Set the Chain Sewing)
1. Start(Set the Number of the Start Back-Tack Stitches)
2. End(Set the Number of the End Back-Tack Stitches)
) is used to determine the clamp type (sewing size) for BH6100-02.
*
1. Stitch (Stitch No. Setting)
2. Length (Up/Down Knife Space)
3. Slant (Slant Compensation)
1. Pitch (Pitch Setting)
2. Length (Pattern Length Setting)
1. Offset (Taper Start Position)
2. Length (Length Setting)
1. Stitch (Stitch No. Setting)
2. Length(Up/Dn knife space)
3. Slant (Slant Compensation)
1. Pitch (Pitch Setting)
2. Length (Pattern Length Setting)
1. Stitch (Stitch No. Compensation)
2. Length (Stitch Length Compensation)
3. Overlap (Overlap Setting)
1. Stitch (Stitch No. Setting)
2. Length(Up/Dn knife space)
3. Slant (Slant Compensation)
1. Pitch (Pitch Setting)
2. Length (Pattern Length Setting)
1. Stitch (Stitch No. Compensation)
2. Length ( Radiation pattern long)
1. X_Comp (X-direction Compensation)
2. Y_Comp(Y-direction Compensation)
[Scope of parameter values]
1000[rpm]~2200[rpm]
1000[rpm]~2200[rpm]
4[stitches]~20[stitches]
-1.0[mm]~1.0[mm]
1~5
0.2[mm]~2.0[mm]
5[mm]~38[mm]
0.3[mm]~2.0[mm]
0.0[mm]~20.0[mm]
4[stitches]~20[stitches]
-1.0[mm]~1.0[mm]
1~5
0.2[mm]~2.0[mm]
5[mm]~38[mm]
5[stitches]~18[stitches]
2.0[mm]~6.0[mm]
0.0[mm]~2.0[mm]
4[stitches]~20[stitches]
-1.0[mm]~1.0[mm]
1~5
0.2[mm]~2.0[mm]
5[mm]~38[mm]
5[stitches]~20[stitches]
0
2.0[mm]~5.0[mm]
-1.0[mm]~1.0[mm]
16[stitches]~60[stitches]
1~6
-0.5[mm]~0.5[mm]
-0.5[mm]~0.5[mm]
5[pulse]~20[pulse]
( )
*
-6~6
-3~5
-6~6
-1.0[mm]~1.0[mm]
-1.0[mm]~1.0[mm]
-6~6
-1~6
-1.0[mm]~1.0[mm]
-5~5
-1.0[mm]~1.0[mm]
-1.0[mm]~0.0[mm]
-6~6
On / Off
1[unit]~15[unit]
0[stitches]~2[stitches]
0[stitches]~2[stitches]
17