Table of Contents
Advertisement
Installation/Operation
Figure 2-7 Removing Acceptor Unit
2. Carfully position the Optional UBA 10/11/
12 or UBA 14/24 Conversion Board and
insert the M2.6×6 Binding/Self Tightening
Phillips mounting screws into the two (2)
Circuit Board Mounting Holes (See Figure
2-8 a
& a
).
1
2
a
Figure 2-8 Installing Optional Circuit Board
3. Tighten each of the mounting screws using a
Phillips Head Screw Driver to secure the
Circuit Board in place on the Transport
Assembly (See Figure 2-8 b).
JCM Part No. 960-000097R_Rev. 3
Universal Bill Acceptor (UBA-1x-SS & UBA-x4-SS/SU)
a
1
2
b
Optional Conversion Board and Harness
Kits
Optional Conversion Board/Harness Kits can be
attached to any UBA 10/11/12-SS or UBA 14/24-
SS Unit. Two Circuit Board and Harness Combina-
tion Kits are available for the UBA 10/11/12-SS
Units and are listed in Table 2-8.
Table 2-8 UBA-10/11/12-SS Conversion Board
and Harness Kit Options
UBA-10/11/12 Conversion Board & Harness Kit Options
RS-232C I/F
Harness
Harness with M3x12
Types
Screws, Springs, Flat
Washer & Clamp
(JAC Part#: 400-
Board
100556RA)
Types
(EDP# 124736)
24VDC/13.5VDC
& RS-232C
UBA 24V/RS-232C
Signal Level
Board plus RS-232C
Conversion
Harness Kit
Board
(JAC Part#: 701-
(JAC Part#: 300-
100097R)
500007R
(EDP# 123200)
(EDP#: 122467)
Three Circuit Board and Harness Combination Kit
types are also available for use with the UBA 14/
24-SS Units and are listed in Table 2-9.
Table 2-9 UBA-14/24-SS Conversion Board and
Harness Kit Options
UBA-14/24 Conversion Board & Harness Kit Options
Harness
DC24V/DC13.5V
and RS-232C Signal
Types
Level Conversion
Board
(JACPart#: )
Types
(EDP# 122467)
24VDC/13.5VDC
& RS-232C
UBA 24V/RS-232C
Signal Level
Board plus RS-232C
Conversion
Harness Kit
Board
(JAC Part#: 701-
(JAC Part#: 300-
100097R)
500007R
(EDP# 123200)
(EDP#: 122467)
RS-232C Signal
UBA RS-232C Board
Level
plus RS-232C
Conversion
Harness Kit
Board
(JAC Part#: 300-
(JAC Part#: 300-
100439RA)
200139R)
(EDP# 123522)
(EDP#: 123523)
External Interface Connection Structure
for an Optional Conversion Board
Figure 2-9 illustrates the External Interface Con-
nection Structure for an Optional Conversion
Board. Table 2-10 lists the Pin Assignments for the
CN2 Connector shown at Figure 2-9 , and Table
2-10 lists the pin assignments for the Relay Con-
nector shown at Figure 2-9 .
© 2010, JCM American, Corporation
2 - 7
Section 2
Photo-Coupler I/F
Harness with M3X12
Washer Sems Screw
and Clamp
(JAC Part#: 701-
100095R)(EDP#
124738)
UBA 24V/RS-232C
Board plus Photo-
Coupler Harness Kit
(JAC Part#: 701-
100098R)
(EDP# 123521)
Photo-Coupler I/F
Harness with M3X12
Washer Sems Screw
Board
and Clamp
(JAC Part#: )
(EDP# 122469)
UBA 24V/RS-232C
Board plus Photo-
Coupler Harness Kit
(JAC Part#: 701-
100098R)
(EDP# 123521)
N/A
Advertisement
Table of Contents
