Table of Contents
Advertisement
Section 2
Connector Pin Assignments (Continued 3)
Table 2-5 list the UBA Front Panel Bezel Connector pin assignments.
Table 2-5 UBA-1X & UBA-x4 Front Panel Bezel Connector Pin Assignments
Pin
Signal Name
No.
1
NC
2
NC
3
TXD
4
NC
5
+12V Power
6
GND (Power)
7
LED Power
8
LED -
*. I/O (input/output) is the terminal viewed from Bill Acceptor's side.
Optional Conversion Circuit Boards
and Harnesses
UBA 10/11/12-SS Optional Conversion
Circuit Board
An Optional Conversion Board can be attached to a
UBA-10/11/12 Unit. Two types of Optional Con-
version Board are available and are listed in Table
2-6.
Table 2-6 UBA-10/11/12SS Circuit Board
Conversion Options
UBA-10/11/12-SS Circuit Board Conversion Options
Part No.
24VDC/13.5VDC and RS-232C
Signal Level Conversion Board
4033-3240-06-13A-01
This board will allow a 24VDC to
JAC Part#: 300-500007R
13.5VDC voltage conversion and
(EDP#:122467)
RS-232C Interface communications
capabilities.
4033-3240-06-15-01
cc-Talk I/F Signal Level Conversion
Board. This Board allows comm-
JAC Part#: 300-200139R
unication with a cc-Talk Interface.
(EDP#: 123523)
NOTE: When installing any Optional
Conversion Board into a UBA Unit, set the
CPU Board Jumper Plugs to "Photo-
Coupler" regardless of the interface type
desired. See Figure 2-11 and Figure 2-12
for proper Jumper setting conditions for the
Board being used.
JCM Part No. 960-000097R_Rev. 3
Universal Bill Acceptor (UBA-1x-SS & UBA-x4-SS/SU)
UBA Front Panel Bezel Connector (CN13)
Header Type: RF-H08(07)2SD-1110 (JST)
Contact Type: RF-SC2210 (JST)
Housing Type: RF-08 (JST)
Wire Type: UL1007 AWG#24~26 Recommended
*
I/O
Reserved
Reserved
Out Transmit signal output line from Acceptor to Controller
Reserved
+12V DC Power
0V DC Ground Plain
LED Drive Line (anode)
LED Drive Line (cathode)
Board Function
2 - 6
Signal Description
UBA 14/24-SS Optional Conversion
Circuit Board
The Optional Conversion Board can also be
attached to a UBA-14/24 Unit. Two types of
optional conversion board are available. Table 2-7
list the available UBA-14/24-SS Optional Conver-
sion Circuit Boards.
Table 2-7 UBA-14/24SS Circuit Board Conversion
Options
UBA-14/24-SS Circuit Board Conversion Options
Part No.
24VDC/13.5VDC and RS-232C
Signal Level Conversion Board
4033-3240-06-13A-01
This board will allow a 24VDC to
JAC Part#: 300-500007R
13.5VDC voltage conversion and
(EDP#:122467)
RS-232C Interface communications
capabilities.
RS-232C Signal Level Conversion
4033-3240-06-13A-02
Board. This board allows comm-
JAC Part#: 300-200139R
unication with an RS-232C
(EDP#: 123523)
Interface.
Optional Conversion Circuit Board
Installation Procedure
To Install an Optional Conversion Board, proceed
as follows:
1. Press down on the UBA Acceptor's Front
Release Latch and slide the Acceptor Unit
forward and off the transport platform
(See Figure 2-7 inset).
© 2010, JCM American, Corporation
Installation/Operation
Board Function
Advertisement
Table of Contents
