Electrical Installation In General - Danfoss VLT HVAC Basic Drive FC 101 Quick Manual

Quick Guide
The dimensions are only for the physical units, but when installing in an application it is necessary to add space for free air
passage both above and below the units. The amount of space for free air passage is listed in Table 1.6:
Enclosure
Frame
H1
H2
H3
H4
H5
H6
H7
H8
H9
H10
I2
I3
I4
I6
I7
I8
Table 1.6 Clearance Needed for Free Air Passage

1.3.3 Electrical Installation in General

All cabling must comply with national and local regulations on cable cross-sections and ambient temperature. Copper
conductors required, (167 °F [75 °C]) recommended.
Power (hp [kW])
Frame IP 3x200–240 V
class
H1 IP20 0.34–2 [0.25–1.5]
H2 IP20 3 [2.2]
H3 IP20 5 [3.7]
H4 IP20 7.5–10 [5.5–7.5]
H5 IP20 15 [11]
H6 IP20 11–25 [15–18]
H7 IP20 30–40 [22–30]
H7 IP20 -
H8 IP20 50–60 [37–45]
Table 1.7 Enclosure H1-H8
MG18A522
Quick Guide
IP class
20
20
20
20
20
20
20
20
20
20
54
54
54
54
54
54
3x380–480 V Line
0.5–2 [0.37–1.5] 12.39 [1.4]
3–5 [2.2–4] 12.39 [1.4]
7.5–10 [5.5–7.5] 12.39 [1.4]
15–20 [11–15] 12.39 [1.2]
25–30 [18.5–22] 12.39 [1.2]
40–60 [30–45] 0.18 [4.5]
75 [55] 88.51 [10]
2.95 [75] 123.91 [14]
125 [90] 2
212.42 [24]
Danfoss A/S © Rev. 2014-01-22 All rights reserved.
Clearance [mm]
Above unit
100
100
100
100
100
200
200
225
100
200
100
100
100
200
200
225
Torque (in-lb [Nm])
Motor DC Control
connection terminals
7.08 [0.8] 7.08 [0.8] 4.43 [0.5]
7.08 [0.8] 7.08 [0.8] 4.43 [0.5]
7.08 [0.8] 7.08 [0.8] 4.43 [0.5]
12.39 [1.2] 12.39 [1.2] 4.43 [0.5]
12.39 [1.2] 12.39 [1.2] 4.43 [0.5]
0.18 [4.5] - 4.43 [0.5]
88.51 [10] - 4.43 [0.5]
123.91 [14] - 4.43 [0.5]
2 - 4.43 [0.5]
212.42 [24]
Below unit
100
100
100
100
100
200
200
225
100
200
100
100
100
200
200
225
Ground Relay
7.08 [0.8] 4.43 [0.5]
7.08 [0.8] 4.43 [0.5]
7.08 [0.8] 4.43 [0.5]
7.08 [0.8] 4.43 [0.5]
7.08 [0.8] 4.43 [0.5]
26.55 [3] 4.43 [0.5]
26.55 [3] 4.43 [0.5]
26.55 [3] 4.43 [0.5]
26.55 [3] 4.43 [0.5]
7
1 1