Exterior Light Units; Rear Courtesy Light; Luggage Compartment, Glovebox And Footwell Lights; Headlight - Opel Zafira B MPV 2006 Owners Workshop Manual

6.9 Disconnect the wiring connector and
remove the light unit
9 Disconnect the wiring connector and
remove the light unit (see illustration).
10 Unclip and remove the reflector from the
base of the light unit (see illustration).
11 Pull the relevant bulb from its socket (see
illustration).
12 Install the new bulb, then refit the reflector.
Reconnect the wiring connector, then clip the
light unit back into position.
Rear courtesy light
13 Using a suitable screwdriver, carefully
prise the right-hand side of the light unit out of
position, and withdraw the light unit.
14 Release the locking plate and disconnect
the wiring connector. Remove the relevant
bulb from the light unit.
15 Install the new bulb, ensuring that it is
securely held in position by the contacts. Refit
the wiring connector and locking plate, then
clip the light unit back into position.
Luggage compartment,
glovebox and footwell lights
16 Using a suitable screwdriver, carefully
prise the light unit out of position, and release
the festoon bulb from the light unit contacts
(see illustration).
17 Install the new bulb, ensuring that it is
securely held in position by the contacts, and
clip the light unit back into position.
Switch illumination
18 All the switches are fitted with illumination
bulbs; some are also fitted with a bulb to
show when the circuit concerned is operating.
These bulbs are an integral part of the switch
assembly, and cannot be obtained separately.
Information display illumination
19 Remove the information display unit as
described in Section 10.
20 Twist and remove the relevant bulbholder
from the rear of the unit (see illustration). The
bulbs are integral with the bulbholders.
21 Fit the new bulbholder and bulb, then refit
the information display unit as described in
Section 10.
6.10 Unclip and remove the reflector from
the base of the light unit
6.16 Carefully prise the light unit out of
position, and release the festoon bulb from
the light unit contacts
7
l;xt~riof
fight
t.mit~
r~~val . . ~.rtntting
Note: Disconnect the battery negative terminal
(refer to 'Disconnecting the battery' in the
Reference Chapter) before removing any light
unit, and reconnect the terminal after refitting.
Headlight
A,_
Warning: Xenon dipped beam
~
headlights operate at very
high voltage. Do not touch the
associated wiring when the headlights are
switched on.
1 Remove the front bumper as described in
Chapter 11.
2 Undo the three retaining bolts and withdraw
the headlight unit from the vehicle. Pull out
the locking catch and disconnect the wiring
7.2a Undo the three retaining bolts
(arrowed) and withdraw the headlight unit
from the vehicle
Body electrical systems 12•9
6.11 Pull the relevant bulb from its socket
6.20 Twist and remove the relevant
bulbholder from the rear of the information
display
connector from rear of the headlight unit as it
is withdrawn (see illustrations).
3 Refitting is a reverse of the removal
procedure. On completion, check the headlight
beam alignment using the information given in
~ection 8.
Front indicator
4 The front direction indicator lights are
integral with the headlight units. Removal and
refitting is as described above.
Indicator side repeater
5 Push the light unit toward the front of the
car, and release the rear edge of the unit from
the wing (see illustration 5.28). If necessary,
assist removal using a suitable plastic wedge,
taking great care not damage the painted
finish of the wing.
6 Withdraw the light unit from the wing, and
disconnect its wiring connector. Tie a piece of
7.2b Pull out the locking catch and
disconnect the wiring connector