Intake Manifold Bolt Torque Sequence - Lincoln Continental 1964 Shop Manual

(145)
from the tube leading into the intake
manifold fitting.
14. Disconnect the fuel inlet 1ine
at the carburetor and fuel filter. Dis-
connect the vacuum line from the
distributor diaphragm and carbure-
tor.
15. Loosen the clamp and discon-
nect the coolant bypass hose at the
wa.ter pump.
16. On a car with an air condi-
tioner, remove the compressor sup-
port bracket.
17. Remove the intake manifold
mounting bolts, clamps and washers.
With assistance, remove the intake
manifold assembly.
18. If the manifold is to be dis-
assembled, remove the bypass hose
and clamps, bypass tube, carburetor
gaskets and spacer, fuel lines, vac-
uum lines, transmission carburetor
linkage, temperature sending unit,
vacuum inlet line fitting and heater
outlet elbow fitting. Discard all gas-
kets.
CLEANING AND INSPECTION
Refer to Part 8-1, Section 3 for
the cleaning and inspection proced-
ures.
INSTALLATION
1. If the intake manifold was dis-
assembled, install the bypass hose
and clamp, bypass tube, temperature
sending unit and the heater outlet
elbow fitting, using water-resistant
sealer. Install the vacuum inlet line
fitting, transmission carburetor link-
age, vacuum lines and fuel lines. In-
stall the carburetor spacer and new
gaskets.
2. Clean the mating surfaces of
the intake manifold and cylinder
heads.
3. Install the intake manifold gas-
kets on the respective cylinder heads,
with the word FRONT (imprinted
on the gaskets) facing toward the
front of the engine. To keep the gas-
kets temporarily in position, install
manifold clamp bolts in the cylinder
heads. The intake manifold gas-
kets are interchangeable from one
cylinder bank to the other.
4. With assistance, lift the intake
manifold and insert the bypass hose
over the water pump inlet tube; then,
position the manifold on the cylin-
der heads. Make certain the gasket
holes are properly aligned.
5. Remove the gasket locating
bolts. Install the intake manifold
mounting bolts, clamps, studs, nuts
and washers. Torque the mounting
PART 8-2-430 V-8 ENGINE
FIG.
11-lntake Manifold
Bolt Torque Sequen'e
A1830·A
bolts in sequence to specifications as
shown in Fig. 11.
6.
On a car with an air conditioner,
install the compressor support brack-
et and tighten the mounting bolts
anJ nuts.
7. Coat one side of a new coolant
supply tank mounting gasket with
water-resistant sealer and install it on
the supply tank. Insert the thermo-
stat into the manifold.
8. Install the coolant supply tank
and coil as a unit on the intake mani-
fold and loosely install the mounting
bolts.
9. Secure the supply tank bracket,
engine ground strap, and battery
ground cable to the water pump and
torque the mounting bolt to specifica-
tions. Torque the coolant supply
tank mounting bolts to specifications.
Connect the overflow hose to the
supply tank.
LO.
Connect the fuel line to the
carburetor and filter. Connect the
vacuum line to the carburetor and
distributor.
11.
Connect the heater outlet hoses
io
the return line and tighten the
clamps. Connect the accelerator link-
age to the accelerator shaft assembly
(hell crank).
12.
Connect the transmission vac-
uum hose to the vacuum line. Con-
nect the vacuum hoses to the intake
8-25
manifold fitting located below the
carburetor.
13. Install the positive crankcase
ventilation tube
~d
hose. Install the
tube on the mounting bracket, lo-
cated on the
inta~e
manifold, a.nd
tighten the retaining clamp.
14. Connect the heater outlet hoses
and automatic choke coolant supply
hose to the fitting located on the in-
take manifold and tighten the retain-
ing clamps.
15. Connect the automatic choke
coolant return hose to the heater
return line and tighten the clamp.
16. Connect the radiator inlet hose
to the radiator and supply tank.
Tighten the retaining clamps.
17. Install the wiring loom in the
clips located on the right bank rocker
arm cover. Install the ignition coil
primary and secondary wires, tem-
perature sending unit wire, and the
oil pressure sending unit wire,
18. On a car with an air condi-
tioner, connect the lead wire to the
fast idle solenoid.
19. Install the distributor cap and
spark plug wires as a unit. Install
the wires on the rocker arm cover
and the spark plugs.
20. Install the battery ground cable
on the battery. Close the radiator
drain cock and the cylinder block
drain plugs. Fill the cooling system.
Start the engine; bleed the cooling
system and fill it to its required level.
21. Check and adjust the initial
timing, if necessary. Adjust the car-
buretor fuel and idle mixture ad- ..
justments. Adjust the transmission
linkage.
22. Check the engine for vacuum,
fuel, coolant and oil leakage.
23. Install the fresh air inlet duct
assembly on the exhaust manifold.
Install the air cleaner.
24. Remove the fender covers.
Close the hood.
EXHAUST MANIFOLD
REMOVAL
1. Remove the air cleaner and air
inlet duct assembly. Block the rear
wheels and set the parking brake.
Raise the front of the car with a
floor jack and install safety stands.
2. Disconnect the exhaust mani-
fold(s) at the resonator inlet pipe(s).
3. Remove the nuts and washers
which secure the engine front sup-
port insulators to the underbody side
members.
4. Place a jack under the front
·edge of the oil pan. Position a block