Lincoln Continental 2001 Owner's Manual
  1. Manuals
  2. Brands
  3. Lincoln Manuals
  4. Automobile
  5. Continental 2001
  6. Owner's manual

Lincoln Continental 2001 Owner's Manual

Lincoln continental 2001
Hide thumbs
Table of Contents

Advertisement

Quick Links

www.carburetor-manual.com
Would you like some Free Manuals?
http://carburetor-manual.com/free-shop-manual-club-t-13.html
Also visit
http://freeshopmanual.com
for more Free Manuals
Also Visit my website for 7 FREE Download Manuals starting
with this one.
"The ABC's of Carburetion"
Click Here Now
file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Continental 2001 and is the answer not in the manual?

Questions and answers

Related Manuals for Lincoln Continental 2001

Summary of Contents for Lincoln Continental 2001

  • Page 1 www.carburetor-manual.com Would you like some Free Manuals? http://carburetor-manual.com/free-shop-manual-club-t-13.html Also visit http://freeshopmanual.com for more Free Manuals Also Visit my website for 7 FREE Download Manuals starting with this one. "The ABC's of Carburetion" Click Here Now file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]...

  • Page 2: Table Of Contents

    Contents Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Customer assistance Reporting safety defects Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.

  • Page 3: Introduction

    Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
  • Page 4 Introduction BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is recommended to give the moving parts a chance to break in. INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing.
  • Page 5 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Tether Warning Anchorage Brake System Anti-Lock Brake System Brake Fluid - Traction Control...
  • Page 6 Introduction Vehicle Symbol Glossary Interior Luggage Child Safety Door Compartment Release Lock/Unlock Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid Power Steering Fluid Level Emission System...

  • Page 7: Instrumentation

    Instrumentation Instrument cluster (pg. 8) Headlamp control Wiper/washer control (pg. 25) (pg. 50) Turn signal control (pg. 49) Instrument panel Speed control Autolamp dimmer control Driver air bag (pg. 51) (pg. 26) (pg. 26) (pg. 97)
  • Page 8 Instrumentation Electronic sound system controls* (pg. 51) Message Center Clock Audio system (pg. 14) (pg. 33) (pg. 34) Heated seat control (pg. 86) Climate controls Climate control system (pg. 51) (pg. 27) *if equipped...
  • Page 9 Instrumentation WARNING LIGHTS AND CHIMES – km/h TURN ON HEAD LAMPS FILL ON RIGHT RPMx1000 SERVICE 000000.0 ENGINE SOON BRAKE Service engine soon Your vehicle is equipped with a SERVICE computer that monitors the engine’s ENGINE emission control system. This SOON system is commonly known as the On Board Diagnostics System (OBD...
  • Page 10 Instrumentation These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Service Engine Soon light should turn off.
  • Page 11 Instrumentation Brake system warning Momentarily illuminates when the ignition is turned to the ON position to indicate a system check. Also BRAKE illuminates if the parking brake is engaged. If the brake warning lamp does not illuminate at these times, seek service immediately. Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately.
  • Page 12 Instrumentation • the autolamps are off • the autolamp sensor determines it is night time Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service.

  • Page 13: Fuel Gauge

    Instrumentation Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter. Key-in-ignition warning chime Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the driver’s door is opened. Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’s door is opened.
  • Page 14 Instrumentation Speedometer Indicates the current vehicle speed. km/h Odometer The odometer is located in the message center. It registers the total kilometers (miles) of the vehicle. Pressing the E/M control (if equipped) will alternate between English (miles) and Metric (kilometers) measurements.
  • Page 15 Instrumentation Never remove the coolant reservoir cap while the engine is running or hot. This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. ELECTRONIC MESSAGE CENTER The electronic message center only SYSTEM...
  • Page 16 Instrumentation Basic operation of Memory Profile System In order for the system to be able to store or recall an individual’s seat and mirror position preferences, the Memory Profile must first recognize who will be driving the vehicle. Drivers may identify themselves to the system one of two ways: •...
  • Page 17 Instrumentation If Memory position 1 or Memory position 2 wishes to make MEMORY1 RECALL temporary changes to their seat or outside mirror positions without affecting their preferred positions they may do so by: • Using the switch on the back of the remote transmitter to turn the Memory Profile System OFF prior to pressing the unlock...
  • Page 18 Instrumentation • exterior lamps (front turn, brake and tail) • fuel level • distance to empty • traction control • ride control System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. The message center will display the RESET last selected feature if there are no more warning messages.
  • Page 19 Instrumentation Gear Display Data ERR Warning reappears after key is turned from OFF to ON Check/Tighten fuel cap Brake Lamp Out Check Traction Control Check Ride Control Trunk Ajar Check Steering Assist Low Washer Fluid Air Leveling Disabled Tail Lamp Out Check FRT Turn Lamps Turn on Headlamps DOOR AJAR.
  • Page 20 Instrumentation electrical loads as soon as possible. If the warning stays on or comes on when the engine is operating at normal speeds, have the electrical system checked as soon as possible. LOW FUEL LEVEL. Displayed when you have approximately 80 km (50 miles) to empty.
  • Page 21 Instrumentation the vehicle is loaded beyond the recommended maximum payload. This is a normal condition if the vehicle is overloaded. To correct this condition: 1. Remove or redistribute the payload per the recommended maximum requirements. 2. Turn the ignition switch from ON to OFF to ON again. If the message reappears: 1.
  • Page 22 Instrumentation DRIVER ID (if equipped) Press this control and use SELECT DRIVER ID to choose DRIVER 1 or DRIVER 2 when choosing operator selectable features. Seat and mirror positions and nine operator selectable features, found under the MENU and VEHICLE HANDLING controls, will be saved to DRIVER 1 or DRIVER 2. These will be automatically recalled when the drivers identify themselves to the system with the remote entry transmitter (refer to Basic Operation of Memory Profile System in this section) or selecting...
  • Page 23 Instrumentation SELECT Press the SELECT control to change SELECT settings in MENU or VEHICLE HANDLING modes. VEHICLE HANDLING Press this control to adjust the VEHICLE HANDLING STEERING EFFORT SETTINGS between NORMAL, LOW and HIGH. Vehicles equipped with the DRIVER ID control, press this control once to adjust RIDE CONTROL SETTINGS between NORMAL, PLUSH and FIRM.
  • Page 24 Instrumentation DTE/ECON • Press the DTE/ECON control DTE ECON once to display approximately how far you can drive before running out of fuel, or the distance to empty (DTE). To ensure accuracy, turn the ignition OFF when you fill the tank. •...
  • Page 25 Instrumentation 1. Set the speed control. Refer to Speed control in the Controls and features chapter. 2. Press the Distance to Empty DTE ECON (DTE) Economy (ECON) control until “Average Miles per Gallon” is displayed. 3. Press the RESET control to clear RESET the DTE/ECON system memory.

  • Page 26: Controls And Features

    Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps only. Rotate to the second position to also turn on the headlamps. The exterior lamps will illuminate when the ignition is ON and the windshield wiper control is in the interval, LO or HI position.
  • Page 27 Controls and features High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the PANEL instrument panel during headlight and parklamp operation.
  • Page 28 Controls and features • To turn autolamps on, push the control up toward the MAX position. As you press this switch, the autolamp system’s status will be displayed in the message center. The system can be set to provide light for up to three minutes after you turn the ignition OFF. •...
  • Page 29 Controls and features remains automatic unless the fan speed control is pressed or the steering wheel controls (if equipped) are pressed. When in AUTO and weather conditions require heat, air will be sent to the floor. However, if the engine is not warm enough to provide heat, the fan will not operate.
  • Page 30 Controls and features Temperature conversion Press MAX A/C and FRONT FRONT the same time (for one second) to ˚ switch between Fahrenheit and REAR Celsius. AUTO Your vehicle has an English/Metric (E/M) control to change your electronic message center display from English to Metric. This control will also change the temperature display.
  • Page 31 Controls and features However, the air conditioning will only function if the outside temperature is about 6°C (43°F) or higher. Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle.
  • Page 32 Controls and features Displaying outside temperature Press EXT to display the outside air temperature. It will be displayed until EXT is pressed again. AUTO If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window.
  • Page 33 Controls and features • Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants. •...
  • Page 34 Controls and features REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. FRONT Press the rear defroster control to clear the rear window of thin ice REAR and fog. • A small LED will illuminate when the rear defroster is activated.
  • Page 35 Controls and features USING YOUR AUDIO SYSTEM Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operation selected will be lit, while the controls which have no function for that mode will be turned off.
  • Page 36 Controls and features High Level Audio System with AM/FM Stereo/Cassette (Radio Controlled CD Changer Compatible) BASS TREB FADE PUSH ON TAPE DOLBY B NR SCAN AUTO SEEK TUNE MUTE SIDE 1-2 COMP SHUFF Your vehicle is equipped with a delayed accessory feature. This feature enables the audio playing media to continue playing up to 10 minutes after the ignition has been turned off, or until a door is opened.
  • Page 37 Controls and features Speed sensitive volume With this feature, radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. The recommended level for speed sensitive volume is from level 1 through level 3. Level 0 turns the speed sensitive volume off and level 7 is the maximum setting.
  • Page 38 Controls and features Tune adjust The tune control works in radio or CD mode (if equipped). Tune adjust in radio mode • Press to move to the next TUNE frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.
  • Page 39 Controls and features Seek function for CD changer (if equipped) • Press to seek to the previous track of the current disc. If a SEEK selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning.
  • Page 40 Controls and features 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. SIDE 1-2 COMP SHUFF...
  • Page 41 Controls and features Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
  • Page 42 Controls and features Rewind The rewind control works in tape and CD modes (if equipped). • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control for less than three seconds results in slow rewind.
  • Page 43 Controls and features Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby ” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Compression feature Compression adjust brings soft and loud CD passages together for a more consistent listening level.
  • Page 44 Controls and features Press the RDS control. Use the SEL control to select ON or OFF to enable or disable the feature. Traffic • Press the RDS control until TRAFFIC is displayed. • Use the SEL control to select ON or OFF.
  • Page 45 Controls and features • Religious • Rock • Soft • Top 40 Show • RDS sends information with the FM broadcast: station name, station type, and/or radio text. • With RDS activated, press the RDS control until SHOW is displayed. •...
  • Page 46 Controls and features Press to eject the magazine. 1. Pull the lever to remove a CD tray from the magazine. 2. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing If you pull too hard on the disc holder, the disc holder may come completely out of the magazine.
  • Page 47 Controls and features 4. Insert the CD magazine into the changer. 5. Slide the door to the left to close. Use only compact discs containing this mark. The magazine does not need to be full for the changer to operate. Radio power must be turned on to play the CDs in the changer.
  • Page 48 Controls and features If your changer does not work, it may be that: • A disc is already loaded where you want to insert a disc. • The disc is inserted with the label surface downward. • The disc is dusty or defective. •...
  • Page 49 Controls and features Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area.
  • Page 50 Controls and features POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF, shuts off the engine and all accessories without locking the steering wheel.
  • Page 51 Controls and features Cornering lamps When the turn signal is used and the headlamps are on, the cornering lamps will light either the right or left side depending on the direction of the turn. The flash rate of the turn signal will speed up considerably if the Lighting Control Module detects a left or right turn lamp bulb (front or rear) is burned out.
  • Page 52 Controls and features STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control features • Press BAND/MODE to select AM, FM1, FM2, TAPE or CD (if equipped). In Radio mode: NEXT • Press MEM/NEXT to select a preset station from memory. In Tape mode: MODE •...
  • Page 53 Controls and features Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on. To turn speed control off •...
  • Page 54 Controls and features Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed.
  • Page 55 Controls and features To set a lower set speed • Press and hold COAST. Release the control when the desired speed is reached or • Press and release COAST to ACCEL operate the Tap-Down function. Each press will decrease the set COAST speed by 1.6 km/h (1 mph) if (E) English is selected or 2km/h (1.25...
  • Page 56 Controls and features To return to a previously set speed • Press RES/RESUME. For RES/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). ACCEL When the RESUME control is pressed, the message “SPEED COAST CONTROL SET” will appear for 5 seconds in your message center.
  • Page 57 Controls and features INTERIOR LAMPS Map lamps To turn on the map lamps, press the control next to each lamp. If equipped with a moon roof, the map lamps are located on the rearview mirror. Press the control next to the map lamp to illuminate the lamp.
  • Page 58 Controls and features MOON ROOF (IF EQUIPPED) To open the moon roof: • Press and hold the control forward to raise the moon roof to the vent position (when the glass panel is closed). • Press the control rearward to fully open the moon roof.
  • Page 59 Controls and features Do not use the HomeLink Universal Transceiver with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S.
  • Page 60 Controls and features Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting after two seconds which may not be long enough to program the HomeLink Universal Transceiver. To program your hand-held transmitters: • continue to hold the button on the HomeLink Universal Transceiver.
  • Page 61 Controls and features 2. Press the training button on the garage door motor head unit (which will activate the “training” light). 3. Press and release the programmed HomeLink button. Press and release the HomeLink button a second time to complete the training process.
  • Page 62 Controls and features The previous device has now been erased and the new device can be activated by pushing the HomeLink button that has just been programmed. ELECTRONIC COMPASS (IF EQUIPPED) The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antennas.
  • Page 63 Controls and features Without moon roof: 1. With the compass display turned on, press and hold the COMP side of the control until the zone selection number appears in the mirror COMP MIRROR display window. 2. Release the COMP side of the control, then press it down again.
  • Page 64 Controls and features Without moon roof: 1. Start the vehicle. 2. Press and hold the COMP side of the control for approximately six seconds until “C” appears in the COMP MIRROR mirror display. 3. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles or on your everyday routine until the display reads a direction.
  • Page 65 Controls and features With moon roof: Press the control to turn the mirror on or off. The mirror will automatically return to the normal state whenever the vehicle is placed in R (reverse)(when the mirror is on) to ensure a bright clear view when backing up.
  • Page 66 Controls and features POWER WINDOWS Press and pull the rocker switches to open and close windows. • Press the top portion of the rocker switch to open. • Pull the top portion of the rocker switch to close. Express down To make the driver window open fully without holding the window control, press the top portion of the...
  • Page 67 Controls and features Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the control. Press the control again to restore the window controls. Accessory delay With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until...
  • Page 68 Controls and features Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
  • Page 69 Controls and features FUEL DOOR RELEASE Your vehicle is equipped with a locking fuel door. To open the door, press the control located on the door. Fuel filler door override release If the remote release is inoperative, open the trunk, then pull the override release handle located inside the trunk on the passenger side to open the fuel filler door.
  • Page 70 Controls and features Mini console (if equipped) The mini console is available in the six passenger vehicle only, and consists of the: • Cupholder • Compact disc changer (if equipped) • Ashtray and lighter Use only soft cups in the cupholder. Hard objects can injure you in a collision.
  • Page 71 Controls and features Arming the system When armed, this system will help protect your vehicle from unauthorized entry. When unauthorized entry occurs, the system will flash the headlamps, parking lamps, interior lamps and the theft indicator lamp and will chirp the horn. The system is ready to arm whenever the key is removed from the ignition.
  • Page 72 Controls and features Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using your remote entry transmitter. • Unlock the doors by using your keyless entry keypad. 7 8 9 0 •...
  • Page 73 Controls and features Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. The horn will chirp to confirm that the control was pressed.
  • Page 74 Controls and features Opening the trunk Press the control once to open the trunk. Ensure that the trunk is closed and latched before driving your vehicle. Failure to latch the trunk may cause objects to fall out of the trunk or block the rear view.
  • Page 75 Controls and features To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation.
  • Page 76 Controls and features Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignition is turned to the RUN or ACC position. The dome lamp control (if equipped) must not be set to the OFF position for the illuminated entry system to operate.
  • Page 77 Controls and features The system can be deactivated by switching the transmitter to OFF. KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: 7 8 9 0 • lock or unlock the vehicle doors without using the key. • arm and disarm the perimeter alarm system (if equipped) See also Remote entry system and Perimeter alarm system in this chapter for more information.
  • Page 78 Controls and features Programming your own entry code 1. Enter the factory-set code (keypad will illuminate when pressed). 2. Press the 1/2 control within five seconds of step 1. 7 8 9 0 3. Enter your personal 5–digit code. Enter each digit within five seconds of the previous one.
  • Page 79 Controls and features Unlocking the doors and releasing the trunk with the keyless entry system To unlock the driver door, enter either the factory-set code or personal code (each digit pressed within 5 seconds of prior digit). The interior lamps will illuminate. To unlock all doors, enter the factory-set code or personal code 7 8 9 0...
  • Page 80 Controls and features The autolock feature can be turned on/off by using the feature menu in the message center. Refer to Electronic message center for more information. SECURILOCK PASSIVE ANTI-THEFT SYSTEM SecuriLock passive anti-theft system is an engine immobilization system. This system prevents the engine from being started unless a coded key programmed to your vehicle is used.
  • Page 81 Controls and features Key information Your vehicle is supplied with two coded keys. Only a coded key will start your vehicle. Spare coded keys can be purchased from your dealership. Your dealership can program your key or you can “do it yourself”, refer to Programming spare keys.
  • Page 82 Controls and features Replacing coded keys can be very costly and you may want to store an extra programmed key away from the vehicle in a safe place to prevent an unforeseen inconvenience. The correct coded key key must be used for your vehicle. The use of the wrong type of coded key key may lead to a “NO-START”...
  • Page 83 Controls and features 5. Within 20 seconds of removing the second coded key, insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from 3 (OFF) to 4 (ON) (maintain ignition in 4 (ON) for at least one second).
  • Page 84 Controls and features Keep vehicle doors and luggage compartment locked and keep keys out of a child’s reach. Unsupervised children could lock themselves in an open trunk and risk injury. Children should be taught not to play in vehicles. On hot days, the temperature in the trunk or vehicle interior can rise very quickly.

  • Page 85: Seating And Safety Restraints

    Seating and safety restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
  • Page 86 Seating and safety restraints Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision.
  • Page 87 Seating and safety restraints Press to move the rear portion of the seat cushion up or down. Heated seats (if equipped) To operate the heated seats: • Slide the control to BACK to heat BACK the seatback only. • Slide the control to BOTH to heat the seatback and the seat cushion.
  • Page 88 Seating and safety restraints Easy access/easy out feature This feature automatically moves the driver’s seat backward when: • the transmission is in N (Neutral) or P (Park) • the key is removed from the ignition cylinder The seat will move 5 cm (2 inches) forward (to the original position) when: •...
  • Page 89 Seating and safety restraints In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair.
  • Page 90 Seating and safety restraints Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.
  • Page 91 Seating and safety restraints • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
  • Page 92 Seating and safety restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down.
  • Page 93 Seating and safety restraints The lap belt does not adjust automatically. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
  • Page 94 Seating and safety restraints Conditions of operation If... Then... The driver’s safety belt is not The safety belt warning light buckled before the ignition switch illuminates 1-2 minutes and the is turned to the ON position... warning chime sounds 4-8 seconds.
  • Page 95 Seating and safety restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider... “Crashes are rare 36 700 crashes occur every day. The more we events” drive, the more we are exposed to “rare” events, even for good drivers.
  • Page 96 Seating and safety restraints One time disable Anytime the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only. Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.
  • Page 97 Seating and safety restraints 6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7.
  • Page 98 Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems. In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity.
  • Page 99 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may effect the performance of the air bag sensors increasing the risk of injury.
  • Page 100 Seating and safety restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
  • Page 101 Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
  • Page 102 Seating and safety restraints If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
  • Page 103 Do not attempt to service, repair, or modify the air bag Supplemental Restraint System, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided.
  • Page 104 Seating and safety restraints The air bag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system.
  • Page 105 Seating and safety restraints If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision. Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician.
  • Page 106 Seating and safety restraints Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’s face or neck, the child should wear the lap and shoulder belt.
  • Page 107 Seating and safety restraints When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter. • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch.
  • Page 108 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
  • Page 109 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
  • Page 110 Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt.
  • Page 111 Seating and safety restraints The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor.
  • Page 112 Seating and safety restraints 5. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 6. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat.

  • Page 113: Starting

    Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
  • Page 114 Starting 2. Make sure the headlamps and vehicle accessories are off. • Make sure the parking brake is HOOD set. • Make sure the gearshift is in P (Park). 3. Turn the key to 4 (ON) without turning the key to 5 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns...

  • Page 115: Starting The Engine

    Starting – km/h TURN ON HEAD LAMPS FILL ON RIGHT RPMx1000 SERVICE 000000.0 ENGINE SOON BRAKE P R N D 3 1 Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. •...
  • Page 116 Starting system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below. For best results, plug the heater in at least three hours before starting the vehicle.

  • Page 117: Driving

    Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
  • Page 118 Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the...
  • Page 119 Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the BRAKE ignition is turned ON) until the parking brake is fully released. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle.
  • Page 120 Driving Wheel-speed sensors allow excess front wheel spin to be detected by the Traction Control portion of the ABS computer. Any excessive wheel spin is controlled by automatically applying and releasing the front brakes in conjunction with engine torque reductions. Engine torque reduction is realized via the fully electronic spark and fuel injection systems.
  • Page 121 Driving • Do not operate the vehicle with a low power steering pump fluid level (below the MIN mark on the reservoir). If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, the condition could be caused by any of the following: •...
  • Page 122 Driving The air suspension shut-off switch is located on the left side of the trunk. If this switch is in the OFF position, the rear air suspension will not operate. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle.
  • Page 123 Driving on the accelerator in each gear. Do not rock the vehicle for more than a few minutes, because it could damage the vehicle. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transaxle may occur. Do not rock the vehicle for more than a few minutes or damage to the transaxle and tires may occur or the engine may overheat.
  • Page 124 Driving Understanding gearshift positions P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This locks the transaxle and prevent the front wheels from rotating. Always set the parking brake fully and make sure the gearshift is securely latched in P (Park).
  • Page 125 Driving N (Neutral) With the gearshift lever in the N (Neutral) position, the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Overdrive) The overdrive position is the normal driving position for an automatic overdrive transaxle.
  • Page 126 Driving When to use 3 (Third) 3 (Third) eliminates the needless shifting back and forth between third and fourth gears that your vehicle may do when driving on hilly terrain. It also gives more engine braking than overdrive to slow your vehicle on downgrades.
  • Page 127 Driving When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). Turn off the ignition whenever you leave your vehicle. Never leave your vehicle unattended while it is running.
  • Page 128 Driving • GAWR (Gross Axle Weight Rating): Carrying capacity for each axle system. The GAWR is specific to each vehicle and is listed on the Safety Certification Label on the driver’s door pillar. • GCW (Gross Combined Weight): The combined weight of the towing vehicle (including passengers and cargo) and the trailer.
  • Page 129 38°C [100°F]) Your vehicle does not come from the factory fully equipped to tow. However, you can contact your local Lincoln dealer to get the proper towing equipment. Do not tow a trailer until your vehicle has been driven at least 3 200 km (2 000 miles).
  • Page 130 GVWR not GCWR. Trailer lamps Do not connect a trailer’s lighting system directly to your vehicle’s lighting system. To get the proper equipment for hooking up your trailer’s lamps, see your Lincoln Mercury dealer. Be sure to follow their instructions carefully.
  • Page 131 Driving If you do not install trailer lights correctly, you may cause damage to the vehicle’s lighting system or other vehicle systems. Driving while you tow When towing a trailer: • Ensure that you turn off your speed control. The speed control may shut off automatically when you are towing on long, steep grades.
  • Page 132 Driving These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication. All Front Wheel Drive (FWD) vehicles An example of recreational towing is towing your vehicle behind a Motorhome. The following recreational towing guidelines are designed to ensure that your transmission is not damaged.

  • Page 133: Roadside Emergencies

    In the United States, this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln. In Canada, the card is found in the Roadside Assistance book in the glove compartment.
  • Page 134 In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance Club brochure or by calling 1–877–294–CLUB (1–877–294–2582).
  • Page 135 Roadside emergencies Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button.
  • Page 136 Roadside emergencies Standard fuse amperage rating and color COLOR Cartridge Fuse Mini Standard Maxi Fuse Link Maxi Rating Fuses Fuses Fuses Cartridge Fuses Grey Grey — — — Violet Violet — — — Pink Pink — — — — — —...
  • Page 137 Roadside emergencies The fuses are coded as follows: Fuse/Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description Lighting Control Module: Anti-Theft Indicator Lamp, PWM Dimming Output, Illumination Lamps for Microphone, RR and LR Door Ashtrays, Heated Seat Switches, Rear Defrost Control Switch, EATC Control Panel, Message Center Switches, Speed Control Switches, Cigar Lighter, Console and Ashtray...
  • Page 138 Roadside emergencies Fuse/Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description Virtual Image Instrument Cluster, Lighting Control Module (LCM RUN/START Sense), Autolamp Light Sensor Virtual Image Instrument Cluster, RF Park/Turn Lamp Power Point Fuel Filler Door Release Switch, Trunk Lid Relay Air Bag Diagnostic Monitor, EATC Module, Blower Motor Relay...
  • Page 139 Roadside emergencies Fuse/Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description Lighting Control Module (LCM): Right Headlamp Virtual Image Instrument Cluster, EATC Module — Not Used Shift Lock Actuator, Vehicle Dynamic Module, Virtual Image Instrument Cluster, Rear Window Defrost, Heated Seat Switch Assembly, Low Tire Pressure Module Radio Heated Mirrors...
  • Page 140 Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
  • Page 141 Roadside emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 15A* High Beam 30A* Right Front Passenger Window 30A** Driver’s Seat Module 30A** Passenger’s Seat Module 40A** Ignition Switch 40A** Ignition Switch 40A** Driver Window 30A** Low Speed Cooling Fan 30A** Powertrain Control Module 40A**...
  • Page 142 Roadside emergencies Tire change procedure To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
  • Page 143 Roadside emergencies 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Refer to Anti-theft lug nuts for information on removing anti-theft lug nuts. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your...
  • Page 144 (not the dealer) to get a replacement key. If the lug wrench/lug nut key assembly is lost, see your nearest Ford or Lincoln/Mercury dealer who has access to the master set of keys. Do not use an impact wrench with the anti-theft key.
  • Page 145 Roadside emergencies 3. Turn the wrench in a counterclockwise direction to remove the lug nut. To install the anti-theft lug nut: 1. Insert the key over the locking lug nut. 2. Place the lug nut wrench over the lug nut key and apply pressure on the key with the wrench.
  • Page 146 Roadside emergencies 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off. Connecting the jumper cables 1.
  • Page 147 Roadside emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
  • Page 148 Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
  • Page 149 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
  • Page 150 Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed by wheel lift or flatbed equipment.

  • Page 151: Maintenance And Care

    Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
  • Page 152 Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood HOOD release handle located under the bottom of the instrument panel. 2.
  • Page 153 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L DOHC V8 engine 1. Automatic transmission fluid dipstick 2. Brake fluid reservoir 3. Battery 4. Air filter assembly 5. Engine oil dipstick 6. Engine oil filler cap 7. Power steering fluid reservoir 8.
  • Page 154 Maintenance and care ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan.
  • Page 155 Maintenance and care • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7.
  • Page 156 Maintenance and care Engine oil and filter recommendations Look for this certification trademark. SAE 5W-20 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use Motorcraft or an equivalent oil meeting Ford specification WSS-M2C153–H. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine.
  • Page 157 Maintenance and care BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the scheduled maintenance guide for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir.
  • Page 158 Maintenance and care WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way.
  • Page 159 Maintenance and care • freeze protection down to -36° C (-34° F). • boiling protection up to 129° C (265° F). • protection against rust and other forms of corrosion. • enables calibrated gages to function properly. When the engine is cold, check the level of the engine coolant in the reservoir.
  • Page 160 Maintenance and care Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location. Adding engine coolant Use only Ford Premium Engine Coolant E2FZ-19549-AA (in Canada, Motorcraft CXC-10) or a premium engine coolant that meets Ford specification ESE-M97B44-A.
  • Page 161 Maintenance and care • Engine coolant concentrations above 60% or below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. Plain water may be added in an emergency, but you must replace it with a 50/50 mixture of engine coolant and distilled water as soon as possible.
  • Page 162 Maintenance and care Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter.
  • Page 163 Maintenance and care Vehicles driven year-round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules.
  • Page 164 Maintenance and care TRANSMISSION FLUID Checking automatic transmission fluid Refer to your scheduled maintenance guide for scheduled intervals for fluid checks and changes. Your transaxle does not consume fluid. However, the fluid level should be checked if the transaxle is not working properly, i.e., if the transaxle slips or shifts slowly or if you notice some sign of fluid leakage.
  • Page 165 Maintenance and care Correct fluid level The transmission fluid should be checked at normal operating temperatures 66°C-77°C (150°F-170°F) on a level surface. The normal operating temperature can be reached after approximately 30 km (20 miles) of driving. The transmission fluid should be in this range if at normal operating temperature (66°C-77°C DON’T ADD IF IN CROSSHATCH AREA--CHECH WHEN HOT-IDLING...
  • Page 166 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules.
  • Page 167 Maintenance and care Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
  • Page 168 Maintenance and care • The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
  • Page 169 Maintenance and care To replace the filter, perform the following procedure: 1. In order to gain better access to the filter, turn the ignition key to ON, then turn the wipers on. When the wipers reach the middle of the windshield (wipers in straight up position), turn the ignition to OFF.
  • Page 170 Maintenance and care 5. Remove the filter. Reverse the procedure to install the new filter. Be careful when installing the new filter. Avoid bending or tearing the filter and make sure it is fully seated in its mounting location after installation.
  • Page 171 Maintenance and care Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the...
  • Page 172 If the warning remains on after you have adjusted the tires to the recommended air pressure levels, take your vehicle to an authorized Lincoln/Mercury dealer for service. Flat tire warning If the sensors detect a tire pressure lower than 68 kPa (10 psi), the LOW...
  • Page 173 Maintenance and care Servicing your SecuriTires If you cannot service your SecuriTire immediately, replace it with your temporary spare as soon as safely possible. Your temporary spare tire can be used until your SecuriTire has been repaired. It is recommended that you always have your SecuriTires serviced by an authorized Michelin tire dealer.
  • Page 174 Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
  • Page 175 Maintenance and care SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
  • Page 176 Maintenance and care Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification or Tire Label.
  • Page 177 Maintenance and care Do not use any type of tire chains on this vehicle. This includes both conventional and cable-type chains. The tires on your vehicle have all-weather treads that provide traction in rain or snow. However, during the winter months in some climates, you may need to use snow tires.
  • Page 178 Maintenance and care Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury.
  • Page 179 Maintenance and care The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: •...
  • Page 180 Maintenance and care The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible...
  • Page 181 Maintenance and care unleaded gasoline. If the problems persist, see your dealer or a qualified service technician. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use high quality fuel of the recommended octane rating.
  • Page 182 Maintenance and care Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver.
  • Page 183 Maintenance and care • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1.
  • Page 184 Maintenance and care • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually. • Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15% less fuel than traveling at 105 km/h [65 mph]). • Revving the engine before turning it off may reduce fuel economy. •...
  • Page 185 Maintenance and care • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. • Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. •...
  • Page 186 Maintenance and care Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the “Service Engine Soon” light, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly.
  • Page 187 Maintenance and care engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. REPLACING EXTERIOR BULBS Check the operation of the following lamps frequently: • Headlamps •...
  • Page 188 Maintenance and care 4. Remove the protective dust shield from the housing by turning the dust shield counterclockwise (when viewed from the rear). 5. Disconnect the electrical connector from the bulb by pulling rearward. 6. Remove the bulb retaining ring by rotating it counterclockwise.
  • Page 189 Maintenance and care To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
  • Page 190 Maintenance and care 3. At the back of the headlamp, pull back and up slightly on the two retainer pins to release the headlamp assembly from the vehicle and pull headlamp forward. 4. Rotate the bulb socket counterclockwise and remove from lamp assembly.
  • Page 191 Maintenance and care Replacing high-mount brakelamp bulbs 1. Open luggage compartment. Note the number of the pin-type retainers before removal. 2. Remove the pin-type retainers from the lower back trim panel. 3. Carefully pull down the lower back trim panel. 4.
  • Page 192 Maintenance and care 5. Carefully remove the bulb socket from the lamp assembly. 6. Carefully pull the bulb from the socket and push in the new bulb. To install, reverse the removal procedure. Replacing backup lamp bulbs For bulb replacement, see a dealer or qualified technician. Replacing tail lamp/turn lamp bulbs For bulb replacement, see a dealer or qualified technician.
  • Page 193 Maintenance and care Function Trade Number Luggage compartment lamp (decklid ajar) Side marker (front) 194 AK (amber) Side marker (rear) Stoplamp and tail lamp 3157K Redundant turn lamp (rear) 3157K Glovebox lamp Ash receptacle 1445 Ash tray (rear) Cigar lighter (console) 1893 Door mounted lamp (front) 214-2...
  • Page 194 Maintenance and care Horizontal aim adjustment 1. Park the vehicle on a level surface. 2. With the hood open, remove the protective cover, locate the horizontal indicator and the adjusting screw at the rear of the headlamp assembly. 3. Use a 4 mm wrench or socket to turn the horizontal adjusting screw until the “0”...
  • Page 195 Maintenance and care Vertical aim adjustment 1. Park the vehicle on a level surface. 2. With the hood open, remove the protective cover, then locate the bubble level and the vertical adjustment screw. The adjustment screw is located on the outboard side of the headlamp.
  • Page 196 Maintenance and care Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results.
  • Page 197 Maintenance and care recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield. Repairing paint chips Minor scratches or paint damage from road debris may be repaired with the Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), Lacquer Touch-up Paint (#ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line.
  • Page 198 Maintenance and care Cleaning the wiper blades, windshield and rear window If the wiper blades do not wipe properly, clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.
  • Page 199 Maintenance and care • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth.
  • Page 200 Maintenance and care Inside windows Use Ultra-Clear Spray Glass Cleaner (E4AZ-19C507–AA) for the inside windows if they become fogged. Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing.

  • Page 201: Capacities And Specifications

    Capacities and specifications MOTORCRAFT PART NUMBERS Component 4.6L DOHC V8 engine Engine air filter element FA-1615 Cabin Air filter element FP-5 Fuel filter FG-800A Battery BXT-65-750 Oil filter FL-820-S PCV valve EV-111 Spark plugs* AWSF-32E * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.
  • Page 202 Capacities and specifications LUBRICANT SPECIFICATIONS Ford Part Ford Part Ford Item Name or Number Specification equivalent Brake fluid High C6AZ-19542-AB ESA-M6C25-A Performance and DOT 3 DOT 3 Motor Vehicle Brake Fluid Hinges, latches, Multi-Purpose DOAZ-19584-AA ESB-M1C93-B or stricker plates, Grease ESR-M1C159-A fuel filler door F5AZ-19G209-AA...
  • Page 203 Capacities and specifications ENGINE DATA Engine 4.6L DOHC V8 engine Cubic inches Recommended fuel 91 octane Firing order 1-3-7-2-6-5-4-8 Spark plug gap 1.3-1.4 mm (0.052-0.056 inch) Ignition system Coil on plug Compression ratio 9.8:1 VEHICLE DIMENSIONS Vehicle dimensions mm (in) (1) Overall length 5 294.7 (208.4) (2) Overall width...

  • Page 204: Certification Label

    Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety MFD. BY FORD MOTOR CO. IN U.S.A. Administration Regulations require DATE: XXXXX GVWR:XXXXX LB/ XXXXX KG that a Certification Label be affixed FGAWR: XXXXXX/XXXXXXX RGAWR: XXXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL to a vehicle and prescribe where the MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE Certification Label may be located.
  • Page 205 Capacities and specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side XXXXXXXXXXXXXXXXX instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and...

  • Page 206: Customer Assistance

    • protection against covered repair costs after your Bumper to Bumper Warranty expires You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs.
  • Page 207 Customer assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership.
  • Page 208 Customer assistance If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
  • Page 209 What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance as designed concerns on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving: •...
  • Page 210 • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs...
  • Page 211 Customer assistance • a brief summary of the action taken by the dealer(s) and Ford Motor Company • the names (if known) of all the people you contacted at the dealership(s) • a description of the action you expect to resolve your concern You will receive a letter of explanation if your application does not qualify for Board review.
  • Page 212 Customer assistance You may also contact the North American Customer Relationship Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 or by writing to the Center at the following address: Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P.O.
  • Page 213 Customer assistance The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel.
  • Page 214 FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
  • Page 215 Customer assistance Comfort and convenience Cargo nets Cargo organizers Engine block heaters Travel equipment Inside mirror, electrochromic with compass (with and without temperature display) Trailer lamp plug and wiring Protection and appearance equipment Air bag anti-theft locks Carpet floor mats (premium) Door edge guards Emergency kit First aid kit...
  • Page 216 Customer assistance • Mobile communications systems may harm the operation of your vehicle, particularly if they are not properly designed for automotive use or are not properly installed. When operated, such systems may cause the engine to stumble or stall or cause the transmission to be damaged or operate improperly.
  • Page 217 Customer assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer...

  • Page 218: Reporting Safety Defects

    Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.

  • Page 219: Index

    Index Accessory delay ......66 Battery ........165 acid, treating emergencies ..165 Air bag supplemental charging system restraint system ....97, 101 warning light ......11 and child safety seats ....99 jumping a disabled battery ..144 description ......97, 101 maintenance-free ....165 disposal ........104 replacement, specifications ...200 driver air bag ....99, 102 servicing ........165 indicator light .....9, 101, 103...
  • Page 220 Index instrument panel ....198 The Dispute interior ........199 Settlement Board ....208 mirrors ........196 Utilizing the Mediation/ plastic parts ......196 Arbitration Program ....211 safety belts ......199 washing ........195 waxing ........195 wheels ........196 Daytime running lamps windows ........199 (see Lamps) ........25 wiper blades ......197 Defrost woodtone trim ......198 rear window ......33...
  • Page 221 Index Engine oil ........153 change oil soon warning, message center .......153 Garage door opener ....57 checking and adding ....153 Gas cap (see Fuel cap) ....178 dipstick ........153 Gas mileage filter, specifications ..155, 200 (see Fuel economy) ....181 recommendations ....155 refill capacities ......200 Gauges .........12 specifications ....201–202 engine coolant...
  • Page 222 Index Heating ........27 HomeLink universal Lamps transceiver (see Garage door autolamp system .......26 opener) ........57–60 bulb replacement Hood ..........151 specifications chart ....191 cargo lamps .......26 daytime running light ....25 headlamps .........25 Ignition .........49, 202 headlamps, flash to pass ..26 instrument panel, dimming ..26 Infant seats interior lamps ....56, 191 (see Safety seats) .....105...
  • Page 223 Index Power steering ....119–120 fluid, checking and adding ..162 Message center ....14, 16, 22 fluid, refill capacity ....200 air leveling disabled ....14 fluid, specifications ..201–202 air ride switch off .....14 check air ride system ....14 check air suspension ....14 menu button ......21 Radio ..........34 reset button ......22 Relays ........134, 140...
  • Page 224 Index heated ........86 Transaxle memory seat ......75 automatic operation ....121 fluid, refill capacities ....200 SecuriLock passive lubricant specifications ..202 anti-theft system ....79–81 Transmission Servicing your vehicle ....150 fluid, checking and adding Spark plugs, specifications ..200, (automatic) ......163 lubricant specifications ..201 Specification chart, Trunk ...........82 lubricants ......201–202...

  • Page 225: Filling Station Information

    Filling station information Item Information Required fuel Unleaded fuel only - 91 octane Fuel tank capacity 75.7L (20.0 gallons) Engine oil capacity (includes filter 5.7L (6.0 quarts). Use Motorcraft change) SAE 5W-20 Super Premium Motor Oil, Ford specification WSS-M2C153-H. Automatic transaxle fluid capacity 13.0L (13.7 quarts).

Table of Contents

Save PDF