Inside Rear View Mirror; Front Door Hinge Adjustments; Rear Door Hinge Adjustments; Lock Striker Adjustment - Lincoln Continental 1964 Shop Manual

(353)
PART 17-3-DOORS, WINDOWS AND DECK LID
17-29
UP
AND DOWN ADJUSTMENTS
FIG.
9-Front Door
Hinge Adiustments
R1228-A
6. Remove the windshield outside
upper corner mouldings (Fig. 12).
7. Remove the windshield outside
side mouldings (Figs. 12 and 13).
8. Remove the windshield outside
top moulding.
9. Remove the windshield inside
top moulding and visor retaining
screws.
10. Remove the windshield inside
side mouldings.
11. Remove the instrument panel
front upper finish panel.
IN AND OUT UP AND DOWN ADJUSTMENTS
FIG.
10-Rear Door
Hinge Adiustments
12. Remove the wiper blade and
arm assemblies.
13. Remove the cowl top grille as-
-;embly and disconnect the wind-
shield washer hoses.
14. With a helper, push the wind-
shield, weatherstrip and outside lower
moulding assembly out of the wind-
shield opening and place on a bench.
15. Remove the outside lower
moulding from the weatherstrip and
remove the weatherstrip from the
glass.
16. Clean old sealer from the
weatherstrip and from the wind-
shield opening.
INSTALLATION
1. Apply sealer to the glass groove
of the weatherstrip.
2.
Position the weatherstrip on the
glass, install the lower moulding in
the weatherstrip and install a 1 /s -inch
'\ash cord around the outer perimeter
of the weatherstrip in its body flange
groove (Fig. 14).
3. Apply scaler to the windshield
opening pinchweld flange.
4.
Apply lubricant (liquid soap or
Ru-Glyde) to the weatherstrip where
1t
contacts the pinchweld flange.
5. With the aid of a helper, care-
fully position the windshield in the
opening.
6.
Pull the inside lip of the weather-
strip over the flange by pulling the
sash cord. Pull the sash cord in the
same general plane as the glass. Pull
the sash cord to the bottom corner
of one side and then pull the other
sash cord to the bottom of the other
side. Do not pull one sash cord all
the way around the perimeter of
the glass. While pulling the sash
cord, gently bump the outside of the
windshield with a soft rubber mallet.
7. Install the cowl top grille and
connect the windshield washer hoses.
8. Install the wiper blade and arm
assemblies.
9.
Install the instrument panel
front finish panel.
10. Install the windshield inside
side mouldings.
11. Install the inside top mould-
ing and sun visor retainers.
12. Install the windshield outside
side mouldings, outside top moulding
and the outside upper corner mould-
ings.
13. Install the roof drip side front
mouldings, front upper body pillar
weatherstrip retainers and front up-
per body pillar weatherstrips.
14. Install the sun visors.
LOCK STRIKER
FIG.
11-Lock
Striker Adiustment
15. Transfer the inside rear view
miror (if removed) to the new glass.
16. Clean the windshield glass,
weatherstrip and mouldings.
INSIDE REAR VIEW MIRROR
REMOVAL
1. Clean both the inside and out-
side surfaces of the windshield in the
area of the mirror mounting bracket.
Inspect the windshield for stone chips
and scratches.
2.
Using welding putty or wet rags,
insulate all chips or scratches within
12 inches of the mirror mounting
bracket.
3.
Apply heat to the bracket mount-
ing area from outside the windshield
with a standard 250-watt infrared
bulb (heat lamp) . Hold the lamp ap-
proximately four inches from the
windshield while rotating it in a small
circle.
4.
The mirror mounting bracket
can be pulled off the windshield glass
in approximately eight to ten min-
utes, using the mirror as a handle.
5. Slowly remove the heat lamp.
Do not remove the insulating ma-
terials until the windshield has
cooled to room temperature.
6.
Remove the mirror ·and arm
from the bracket.
INSTALLATION
1. Locate and mark with a wax
pencil the bracket location on the
outside surface of the windshield
(Fig. 15).
2. Use a good grade of "ethyl al-
cohol" to thoroughly clean the inside
glass surfare bracket mounting area
and mounting bracket face. It is im-
portant that the mounting surfaces
are properly cleaned before the resin
is applied.
3. To mix the resin pour the entire
contents of the small catalyst bottle
into the large epoxy bottle (Fig. 15).
4. Properly stir the contents for