Table of Contents
Advertisement
(357)
PART 17-3- DOORS, WINDOWS AND DECK LID
17-33
VENT WINDOW FRAME
1. Remove the trim panel and
water shield.
2.
Remove the vent window motor.
3. Loosen the vent window weath-
erstrip from the front of the vent
window assembly.
4.
Remove the lower stop bumper.
5. Remove the vent window as-
sembly upper attaching screw.
6. Remove the lock nut from the
vent
window
assembly adjusting
screw.
7.
Remove the
lower adjusting
screw and lock nut from the bottom
of the division bar.
8. With the door window down,
remove the vent window assembly
from the door and the front run.
9. Remove the vent window glass
lower pivot bushing assembly.
10. Remove the vent window glass
and frame from the vent window
assembly.
11. Remove the vent window glass
from the vent window frame.
12. To install, reverse the removal
procedure.
FRONT DOOR WINDOW
REGULATOR
REMOVAL
1. Remove the door trim panel and
water shield.
2. Disconnect the regulator arms
from the lower glass channel.
3. Position the glass assembly to
the top of its opening and prop it in
place.
4.
Disconnect the motor wiring
connector, remove the wire retaining
clip, and remove the motor bracket
retaining screw.
5. Remove the four regulator re-
taining screws. Remove the regulator
and motor assembly from the door.
6. Hold the regulator assembly
in a vise and remove the motor as-
sembly.
INSTALLATION
1.
Preload the replacement regu-
lator assembly to the correct position.
Hold the regulator in a vise and in-
stall the motor on the regulator.
2.
Transfer the glass channel roll-
ers to the new regulator.
3. Position the regulator and mo-
tor assembly in the door. Install the
regulator retaining screws and the
motor bracket retaining screw.
4.
Connect
the
regulator
arms
(and rollers) to the lower giass chan-
nel (Fig. 6).
5. Connect the motor lead wires
and install the wiring retaining clips.
6.
Install the water shield and door
trim panel.
FRONT DOOR VENT WINDOW
FRAME AND DIVISION BAR
1.
Remove the door trim panel
and water shield.
2. Remove the vent window motor.
3. Remove
the
retaining screw
from the front of the door weather-
strip and remove the weatherstrip
from the vent frame assembly.
4.
Remove the two lock nuts and
screw retaining the vent assembly to
the door.
5. Tilt the vent assembly in the
door and remove the front run; then,
remove the vent assembly.
6. Remove the two vent window
lower bushing retaining screws and
remove the bushing.
7. Remove the vent glass and
frame from the vent assembly.
8. Remove the vent window weath-
erstrip from the vent window frame
and division bar.
9. To install, reverse the removal
procedure.
REAR DOOR OUTSIDE HANDLE
1. Remove the trim panel and
water shield.
2.
Raise the window to its closed
position.
3. Remove the screw and nut that
secures the handle to the door panel.
4.
Position the handle away from
the door and disconnect the handle-
to·lock rod. Remove the handle and
pads.
5. To instal1, connect the lock rod
at the handle; then, position the door
handle and pads on the door. Install
the attaching screw and nut. Check
the pushbutton for proper clearance
between the release pin and the re-
lease lever arm on the door lock as-
sembly.
6.
Install the water shield and
trim panel.
REAR DOOR LOCK
1. Remove the trim panel and
water shield.
2.
Disconnect the remote control
rod at the door lock.
3. Remove the screws securing the
door lock vacuum control to the
door and disconnect the control rod
from the door lock.
4. Disconnect the door outside
handle rod at the handle.
5. Disconnect the door lock warn-
ing light switch lead wires.
6. Remove the screws securing the
door lock to the door and remove the
lock assembly and rods.
7. Transfer the push butwn rod,
door handle rod and the warning
light switch to the new lock assem-
bly.
8. To install the lock assembly,
reverse the removal procedure.
REAR WINDOW REGULATOR
MOTOR
1. Remove the trim panel and
water shield.
2.
Remove the nuts securing the
motor to the regulator and the motor-
to-door bracket screw. Disconnect
the wiring and remove the motor.
3. To install, reverse the removal
procedure.
REAR DOOR WINDOW
1. Remove the door trim panel and
water shield.
2.
Remove
the
window
upper
stops.
3. Remove the window lower stop.
4.
Disconnect the regulator arms
from the !ower window channel and
lower the window to the bottom of
the door.
5. Remove the door window outer
belt weatherstrip and stabilizer as-
semblies.
6.
On the convertible door window
remove the rear door window control
switch trigger pin from the lower
window frame.
7. Remove the rear window assem-
bly from the door (Fig.
8).
8. Remove the upper frame from
the glass and remove the glass from
the lower glass channel.
9. To install reverse the removal
procedure.
REAR DOOR WINDOW
REGULATOR
1. Remove the door trim
and
water shield.
2.
Disconnect the regulator arms
from the lower window· channel and
prop the window IN THE
UP
POSI-
TION.
3. Disconnect the motor wiring
connector, remove the wiring re-
taining clip and remove the motor
bracket retaining screw.
4.
Remove the four regulator re-
taining bolts and remove the regu-
lator and motor assembly from the
door. The regulator arms must be
in thE: down position.
Advertisement
Table of Contents
Troubleshooting
