Page 1
SAFETY AND ASSEMBLY AND PARTS OPERATIONS MANUAL MANUAL T8 SERIES AUGER T832 SwingMAX T836 T842 T852 T862...
Page 2
PO Box 1996 2800 Pasqua Street North Regina, Sk, Canada S4P 3E1 Declare the Augers listed below conform to the 2006/42/EC Machinery Directive T832 T836 T842 T852 T862 The Harvest by Meridian T Auger is designed for the movement of Grains and Cereals 1300060439-31-00...
Page 3
GENERAL TABLE OF CONTENTS GENERAL Declaration of Conformity Table of Contents Sign Off Sheet ASSEMBLY Tube Identification Tube Assembly B10 Fork Option B12 Hopper Option B18 Frame Identification T832/T836/T842 B19 Frame Identification T852/T862 B20 Frame Assembly B27 Winch and Winch Cable Assembly B29 PTO Drive Option B34 Electric Drive Option B42 Guard Assembly...
Page 4
GENERAL SIGN OFF SHEET As a requirement of OSHA, it is necessary for the employer to train the employee in the safe operation and safety procedures with this equipment. We include this sign-off sheet for your convenience and personal record keeping. 1300060439-33-00...
ASSEMBLY TUBE ASSEMBLY Step 1 Identify the Tube Assembly Sections required for the specific auger model being assembled. See the tube section identification page previous to this page. Step 2 Place tubes on assembly stands. Place stands 12" or less from the end of the tube. Placing stands farther than 12"...
ASSEMBLY TUBE ASSEMBLY Step 4 (Only for T852/T862) Locate the Right Truss Cable Mount Brackets (PN 1300011880-00), Left Truss Cable Mount Brackets (PN 1300011879-00), and bolt bag PN 1300060249-00. Slide the flighting from the Intake and Mid Tubes. Align the flighting as shown in Figure 4.1 to make continuous.
ASSEMBLY TUBE ASSEMBLY Step 6 (Only for T842/T852/T862) Locate the Drive Shaft Coupler (PN1300010950-00) and bolt bag (for T1042 PN: 1300060256-00/for T1052: PN 1300060265-00/for T1062: PN 1300060275-00). Connect the Drive Shaft Mid and the Drive Shaft Discharge using the Drive Shaft Coupler, (2) 3/8" x 2" Flange Lock Bolts, and (2) 3/8"...
ASSEMBLY TUBE ASSEMBLY Step 8 (Only for T852/T862) Locate the Truss Uprights (PN 1300010163-00), Truss Support (PN 1300010174-00), and bolt bag (for T852: PN 1300060260-00/for T862: PN 1300060272-00). Mount the Truss Uprights to the Truss Mount Bracket on the bottom of the Mid Tube and on the top of the Discharge Tube with (for T852: (8) 3/8"...
ASSEMBLY TUBE ASSEMBLY Step 10 (Only for T852/T862) Attach (2) 1/2" x 6-1/4" Eyebolts, and (4) 1/2" Hex Lock Nuts to the Left and Right Truss Cable Mount Brackets on the Intake and Mid Tube connection (see Figure 10.1) (Do not tighten the bolts right now).
ASSEMBLY TUBE ASSEMBLY Step 11 (Only for T852/T862) Locate the Bottom Truss Cables (for T852: PN 1300011945-00/for T862: PN 1300011884-00). Secure the Truss Cables on Truss Support with (2) 3/8" Cable Clamp on the Truss Support (Do not overtighten the clamp, as the cable has to move freely through the clamp) (see Figure 11.1).
Page 13
ASSEMBLY TUBE ASSEMBLY Step 12 (Only for T852/T862) Locate the Top Truss Cables (for T852: PN 1300011017-00/for T862: PN 1300011707-00). Secure the Truss Cables on Truss Support with (2) 3/8" Cable Clamp on the Truss Support (Do not overtighten the clamp, as the cable has to move freely through the clamp) (see Figure 12.1).
Page 14
ASSEMBLY FORK OPTION Step 13 Locate the Fork Housing (PN 1300030890-00), Fork Bushing (PN 1300030801-00), and bolt bag PN 1300060266-00. Attach the Fork Bushing to the Fork Housing with (4) 3/8" x 1" Hex Bolts and (4) 3/8" Flange Lock Nuts (see Figure 13.1). Fork Housing Fork Bushing Figure 13.1: Fork Bushing...
Page 15
ASSEMBLY FORK OPTION Step 15 Slide the Fork Housing assembly over the Intake tube and flighting. Align the Fork Bearing Stub with the Fork Bushing. Slide the Fork Bearing Stub into the Fork Bushing and align the slot in the bottom of the Fork housing with key stock welded to the bottom of the Intake Tube (see Figure 15.1).
Page 16
ASSEMBLY HOPPER OPTION Step 17 Locate the Hopper Pan (PN 1300030983-00), Lube Hole Cover (PN 1300010139-00), 1" Bore Bushing (PN 1300030558-00), and bolt bag PN 1300060250-00. Attach the Lube Hole Cover to the Hopper Pan with (1) 1/4" x 3/4" Hex Bolt and (1) 1/4" Nylon Lock Nut (see Figure 17.1). Mount the Circular Flangettes and 1"...
Page 17
ASSEMBLY HOPPER OPTION Step 19 Locate the Hopper Flight (PN 1300030906-00) and Transition Flight (PN 1300030907-00). Place the Transition Flight on the Hopper Flight and align key slots, secure it with (1) 1/4" x 1/4" x 1-1/2" Key, (1) 5/16" x 1-1/4" Socket Screw, and (1) 5/16" Flange Lock Nuts (see Figure 19.1). Fasteners can be found in bolt bag PN 1300060250-00.
Page 18
ASSEMBLY HOPPER OPTION Step 21 Locate the Hopper Throat (PN 1300030910-00), Hanger Flight Hopper (PN 1300030908-00), and bolt bag PN 1300060251-00. Attach the Hanger Flight Hopper with the Hopper Throat using (2) 3/8" x 1-1/4" Flange Lock Bolts and (2) 3/8" Flange Lock Nuts (see Figure 21.1) (Do not tighten the nuts, since they need to be removed to connect the Tube Connection Hopper).
Page 19
ASSEMBLY HOPPER OPTION Step 23 Locate the Stub Transition Hopper (PN 1300012615-00). Insert the Stub Transition Hopper into the Intake Flight and secure it with (1) 1/2" x 3" Hex Bolt and (1) 1/2" Stover Lock Nut (see Figure 23.1). Fasteners can be found in bolt bag PN 1300060250-00.
Page 20
ASSEMBLY HOPPER OPTION Step 25 Locate the Tube Connection Hopper (PN 1300030911-00). Slide the Tube Connection Hopper into the Hopper Clamp and align the key stock welded to the bottom of the Tube Connection Hopper to the slot in the bottom of the Hopper Clamp (see Figure 25.1). Tighten the bolts on the Hopper Clamp. Tube Connection Hopper Key Welded Hopper Clamp...
Page 21
ASSEMBLY HOPPER OPTION Step 27 Locate the Strap Lid (PN 1300011244-00) and Stop Transport (PN 1300011422-00). Place the Strap Lid on the Hopper Assembly and secure it with the (2) 1/4" x 2-1/8" Lynch Pins (see Figure 27.1). Attach the Stop Transport to the tabs on the Hopper Assembly with (1) 1/2" x 3-1/2" Hex Bolt and (1) Stover Lock Nut (see Figure 27.2).
Page 23
ASSEMBLY FRAME IDENTIFICATION T852/T862 Axle T852: 1300030760-00 Main Frame Right Main Frame Right T862: 1300030969-00 T852: 1300031008-00 T862: 1300030972-00 A-Frame (x2) Main Frame Left Main Frame Left T852: 1300030762-00 T862: 1300031012-00 T852: 1300031009-00 T862: 1300030970-00 Trolley Roller Housing Trolley Brace Cross (x4) T852: 1300030733-00 T852: 1300010929-00 1300010693-00...
Page 24
ASSEMBLY FRAME ASSEMBLY Step 29 (Only for T832/T836/T842/T852) Locate the Main Frame arms, Axle, Hub & Spindle (PN 1300030730-00), and bolt bag (for T832: PN 1300060175-00/for T836/T842: PN 1300060111-00/for T852: PN 1300060206-00). Mount the Hub & Spindles onto the Axle and secure it using (for T832: (4) 1/2"...
Page 25
ASSEMBLY FRAME ASSEMBLY Step 31 (Only for T852/T862) Locate the Cross Braces and bolt bag PN 1300060205-00. Connect the Cross Braces to the Left and Right Main Frame Arms with (5) 3/8" x 1" Flange Lock Bolts and (5) 3/8" Flange Lock Nuts (see Figure 31.1).
Page 26
ASSEMBLY FRAME ASSEMBLY Step 33 Locate the tire (for T832/T1836/T842: PN 13000005448-00/for T852/T862: PN 1300030103-00) and bolt bag PN 1300060180-00. Attach the A-Frame Arms to the Axle with (2) (for T832/T836/T842/T852: 3/4" x 1-3/4" Hex Bolts/for T862: 1" x 2" Hex Bolts) and (2) (for T832/T836/T842/T852: 3/4"...
Page 27
ASSEMBLY FRAME ASSEMBLY Step 35 Locate the Housing Trolley and Trolley Roller. Attach the Housing Trolley and Trolley Roller to A-Frame Arms with (1) (for T832/T836/T842/T852: 3/4" x 6-1/2" Hex Bolt/for T862: 1" x 8" Hex Bolt), (2) (for T832/T836/T842/T852: 3/4" Flat Washers/for T862: 1" Flat Washers), and (1) (for T832/T836/T842/T852: 3/4"...
Page 28
ASSEMBLY FRAME ASSEMBLY Step 37 (Only for T852/T862) Locate the Stop Track (PN 1300010959-00) and bolt bag (for T1052: PN 1300060263-00/for T1062: PN 1300060270-00). For T1052: attach the Stop Track under the Track Angle Short at lower end with (2) 3/8" x 1" Flange Lock Bolts and (2) 3/8" Flange Lock Nuts (see Figure 34.1).
Page 29
ASSEMBLY FRAME ASSEMBLY Step 39 (Only for T832/T836/T842/T852) Attach the Stop Track on the top end of the Track Angle to restrict the Sliding movement of the A-Frame Assemby with (2) 3/8" x 1" Flange Lock Bolts and (2) 3/8" Flange Lock Nuts (see Figure 39.1).
Page 30
ASSEMBLY FRAME ASSEMBLY Step 41 Lift the Main Frame Arms and attach it to the Main Frame Arms Mount Bracket welded on bottom of the Intake Tube with (2) 3/4" x 1-1/2" Hex Bolts and (2) 3/4" Stover Lock Nuts (see Figure 32.1). Do not overtighten nuts as the Main Frame Arms need to be able to rotate about the bolts.
Page 31
ASSEMBLY WINCH AND WINCH CABLE ASSEMBLY Step 43 Locate the winch (PN 1300030108-00) and bolt bag (for T832: PN 1300060171-00/for T836: PN 1300060171-00/for T842: PN 1300060172-00/for T852: PN 1300060259-00/for T862: PN 1300060269-00). Mount the winch onto the winch mount bracket welded at bottom of the Intake Tube with (3) 3/8"...
Page 32
ASSEMBLY WINCH AND WINCH CABLE ASSEMBLY Step 45 Locate the steel cable (for T832/T836: PN 1300010956-00/for T842: PN 1300011943-00/for T852: PN 1300011016-00/for T862: PN 1300011708-00) and bolt bag PN 1300060114-00. Attach the steel cable to the winch by passing the cable through one of the holes in outer plate of the winch. Place the cable under the clamp plate on outer plate.
Page 33
ASSEMBLY PTO DRIVE OPTION Step 46 Locate the Gearbox (PN 1300030176-00), Gearbox Mount (PN 1300032048-00), Band Clamp (PN 1300013280-00), and bolt bag PN 1300060231-00. Mount the Gearbox onto the Gearbox Mount Bracket with (4) 1/2" X 1" Hex Bolts and (4) 1/2" Lock Washers (see Figure 46.1) (Orient the gearbox so the longer spline shaft stays in right side of the Gearbox Mount).
Page 34
ASSEMBLY PTO DRIVE OPTION Step 47 (Only for T836/T842/T852/T862) Locate the Flangettes (PN 1300010656-00), the 1" Bore Bearings (PN 1300010670-00) and bolt bag (for T836: PN 1300060283-00/for T842T852: PN 1300060246-00/for T862: PN 1300060267-00). Attach (for T836: (4) Flangettes and (2) 1" Bore Bearings on the Intake Tube with (4) 5/16"...
Page 35
ASSEMBLY PTO DRIVE OPTION Step 49 Locate the Hub & Sprocket (PN 1300031686-00) and Sprocket PN 1300031685-00. Mount the Sprocket to the end of the Drive Shaft PTO with (1) 3/8" x 2-1/4" Flange Lock Bolt and (1) 3/8" Flange Lock Nut (see Figure 49.1).
Page 36
ASSEMBLY PTO DRIVE OPTION Step 51 Locate the Housing Guard (PN 1300010923-00), Rubber Shield (PN 1300010924-00), and bolt bag (for T832: PN 1300060165-00/for T836: PN 1300060283-00/for T842/T852: PN 1300060246-00/for T862: PN 1300060267-00). Attach the Housing Guard to the gearbox with (4) 5/16" x 1/2" Hex Bolts and (4) Lock Washers (see Figure 51.1).
Page 37
ASSEMBLY PTO DRIVE OPTION Step 52 Locate the PTO Support (PN 1300030609-00). Mount PTO Support to the Mount Bracket on the Intake Tube with (2) 3/8" x 1" Flange Lock Bolts and (2) Flange Lock Nuts (see Figure 52.1). Fasteners can be found in bolt bag (for T832: PN 1300060165-00/for T836: PN 1300060283-00/for T842/T852: PN 1300060246-00/for T862: PN 1300060267-00).
Page 38
ASSEMBLY ELECTRIC DRIVE OPTION Step 54 Locate the Gearbox (PN 1300030176-00), Gearbox Mount (PN 1300032048-00), Band Clamp (PN 1300013280-00), and bolt bag PN 1300060231-00. Mount the Gearbox onto the Gearbox Mount Bracket with (4) 1/2" X 1" Hex Bolts and (4) 1/2" Lock Washers (see Figure 54.1) (Orient the gearbox so the shorter spline shaft stays in left side of the Gearbox Mount).
Page 39
ASSEMBLY ELECTRIC DRIVE OPTION Step 55 (Only for T832) Remove the (2) Flangettes, (1) 1" Bore Bearing, (2) 5/16" x 1" Carriage Bolts, and (2) 5/16" Flange Lock Nuts from the Discharge Tube Bearing mount bracket (see Figure 55.1). Bearing Mount Bracket 1"...
Page 40
ASSEMBLY ELECTRIC DRIVE OPTION Step 57 Locate the Hub & Sprocket (PN 1300031686-00) and Sprocket (PN 1300031685-00). Mount the Sprocket to the end of the Drive Shaft with (1) 3/8" x 2-1/4" Flange Lock Bolt and (1) 3/8" Flange Lock Nut (see Figure 57.1).
Page 41
ASSEMBLY ELECTRIC DRIVE OPTION Step 59 Locate the Motor Mount Clamps (PN1300030613-00) and bolt bag (for T832/T842/T852: PN 1300060254-00/for T836: PN 1300060282-00/for T862: 1300060254-00). Mount the Motor Mount Clamps onto the Tube and secure them with (12) 3/8" x 2" Hex Bolts and (12) 3/8" Nylon Lock Nuts (see Figure 59.1) (Do not tighten the bolts yet).
Page 42
ASSEMBLY ELECTRIC DRIVE OPTION Step 61 Mount Frame Motor Mount Assembly to the Motor Mount Clamps with (8) 3/8" x 1-1/4" Flange Lock Bolts and (8) 3/8" Flange Lock Nuts (see Figure 61.1). Tighten the bolts on Motor Mount Clamps. Fasteners can be found in bolt bag (for T832/T842/T852: PN 1300060254-00/for T836: PN 1300060282-00/for T862: 1300060254-00).
Page 43
ASSEMBLY ELECTRIC DRIVE OPTION Step 63 Locate the Belt Guard Mount (PN 1300010818-00). Attach the Belt Guard Mount to the gearbox with (4) 5/16" x 1/2" Hex Bolts and (4) 5/16" Lock Washers (see Figure 63.1). Fasteners can be found in bolt bag (for T832/T842/T852: PN 1300060254-00/for T836: PN 1300060282-00/for T862: 1300060254-00).
Page 44
ASSEMBLY ELECTRIC DRIVE OPTION Step 65 Locate the Upper Pulley (PN 18345-00) and Hub (PN 1300010358-00). Place the Upper Pulley on the gearbox drive shaft. Slide the Hub on the gearbox drive shaft and secure the hub with the pulley using (2) 1/4"...
Page 45
ASSEMBLY ELECTRIC DRIVE OPTION Step 67 Locate the Belt Guard End Short (PN 1300010821-00) and Belt Guard End Long (PN 1300010820-00). Attach the Belt Guard End Short to the Belt Guard Inner with (2) 5/16" x 3/4" Flange Lock Bolts and (2) 5/16" Flange Lock Nuts (see Figure 67.1). Attach the Belt Guard End Long to the Belt Guard Inner with (2) 5/16"...
Page 46
ASSEMBLY GUARD ASSEMBLY Step 69 Locate the Cover Chain Coupler (PN 1300012529-00). Place the Cover Chain Coupler onto the gearbox and secure it with (4) 1/2" X 1" Hex Bolts and (4) 1/2" Lock Washers (see Figure 69.1) Fasteners can be found in bolt bag PN 1300060231-00. Gearbox Cover Chain Coupler...
Page 48
ASSEMBLY This will complete the assembly for your Harvest by Meridian T832/36/42/52/62 Auger. For additional part numbers, information, & overall views please refer to the parts book drawings located at the end of this assembly manual. 1300060439-80-00...
Page 56
PARTS FRAME T862 HARVEST by MERIDIAN T862 QUANTITY REF # PART # DESCRIPTION 13073000016 NUT, HEX, NYLOCK1-8 UNC Steel, Mild 13073500016 Flat Washer 1 1300030971-00 Roller Track T862 T1062 T1342 1300011673-00 Housing Lift Roller T862 T1062 T1342 13070216128 Hex Cap Screw 1 x 8-8 Gr 5...
Page 57
PARTS TUBE ASSEMBLY T832 1300060439-01-00...
Page 58
PARTS TUBE ASSEMBLY T832 HARVEST by MERIDIAN T832 QUANTITY REF # PART # DESCRIPTION 1300010304-00 Screw, Self Tapping, #12X3/4" 1300010942-00 Guard Drive Shaft Long T Augers 1300030893-00 Tube Discharge T832/36/42 13073100006 NUT, HEX, FLANGED, Steel, Mild 3/8-16 UNC 1300010944-00 Drive Shaft Discharge T8 T1032/36/42...
Page 59
PARTS TUBE ASSEMBLY T836 1300060439-02-00...
Page 60
PARTS TUBE ASSEMBLY T836 HARVEST by MERIDIAN T836 QUANTITY REF # PART # DESCRIPTION 1300010304-00 Screw, Self Tapping, #12X3/4" 1300010942-00 Guard Drive Shaft Long T Augers 1300030893-00 Tube Discharge T832/36/42 13073100006 NUT, HEX, FLANGED, Steel, Mild 3/8-16 UNC 1300010944-00 Drive Shaft Discharge T8 T1032/36/42...
Page 61
PARTS TUBE ASSEMBLY T842 1300060439-03-00...
Page 62
PARTS TUBE ASSEMBLY T842 HARVEST by MERIDIAN T842 REF # PART # QUANTITY DESCRIPTION 1300010304-00 Screw, Self Tapping, #12X3/4" 1300010942-00 Guard Drive Shaft Long T Augers 1300030893-00 Tube Discharge T832/36/42 13073100006 NUT, HEX, FLANGED, Steel, Mild 3/8-16 UNC 1300010944-00 Drive Shaft Discharge T8 T1032/36/42...
Page 63
PARTS TUBE ASSEMBLY T852 1300060439-04-00...
Page 64
PARTS TUBE ASSEMBLY T852 HARVEST by MERIDIAN T852 REF # PART # QUANTITY DESCRIPTION 1300010304-00 Screw, Self Tapping, #12X3/4" 1300010942-00 Guard Drive Shaft Long T Augers 1300031055-00 Tube Discharge T852 13073100006 NUT, HEX, FLANGED, Steel, Mild 3/8-16 UNC 1300010944-00 Drive Shaft Discharge T8 T1032/36/42...
Page 65
PARTS TUBE ASSEMBLY T862 1300060439-05-00...
Page 66
PARTS TUBE ASSEMBLY T862 HARVEST by MERIDIAN T862 QUANTITY REF # PART # DESCRIPTION 1300010304-00 Screw, Self Tapping, #12X3/4" 1300010942-00 Guard Drive Shaft Long T Augers 1300031058-00 Tube Discharge T862 13073100006 NUT, HEX, FLANGED, Steel, Mild 3/8-16 UNC 1300010944-00 Drive Shaft Discharge T8 T1032/36/42...
Page 67
PARTS TRUSS ASSEMBLY T852 DETAIL B DETAIL A DETAIL C DETAIL D DETAIL E DETAIL F 1300060439-09-00...
Page 68
PARTS TUBE ASSEMBLY T852 HARVEST by MERIDIAN T852 REF # PART # QUANTITY DESCRIPTION 1300011945-00 Cable Truss Bottom 5/16" x 24' 13000002433-00 Cable Clamp - 5/16" 1300030976-00 Mount Cable Truss H1074/84XT T852/62 1300010310-00 Eye-Bolt 1/2 x 6-1/4 RH Plated T852/62 T1052/62...
Page 69
PARTS TRUSS ASSEMBLY T862 DETAIL A DETAIL B DETAIL C DETAIL D DETAIL E DETAIL F 1300060439-10-00...
Page 70
PARTS TUBE ASSEMBLY T862 HARVEST by MERIDIAN T862 REF # PART # QUANTITY DESCRIPTION 1300011884-00 Cable Truss Bottom 3/8" x 27' 13000030601-00 Cable Clamp - 3/8" 1300010310-00 Eye-Bolt 1/2 x 6-1/4 RH Plated T852/62 T1052/62 13071210024 Flange Lock Bolt 5/8 x 1 1/2-11 Gr 5...
Page 71
PARTS WINCH CABLE ASSEMBLY T8 1300060439-74-00...
Page 72
PARTS WINCH CABLE ASSEMBLY T8 HARVEST by MERIDIAN T8 QUANTITY REF # PART # DESCRIPTION 1300010956-00 Cable Frame Lift 1/4" x 35' T832/36 1300011943-00 Cable Frame Lift 1/4" x 40' T842 1300011016-00 Cable Frame Lift 1/4" x 55' T852 1300011708-00 Cable Frame Lift 5/16"...
Page 73
PARTS DISCHARGE HEAD T832/T836/T842 1300060439-06-00...
Page 74
PARTS DISCHARGE HEAD T832/T836/T842 HARVEST by MERIDIAN T832/T836/T846 QUANTITY REF # PART # DESCRIPTION 13071204012 Flange Lock Bolt 1/4 X 3/4-20 Gr 5 13070204016 Hex Cap Screw 1/4 x 1-20 Gr 5 1300012673-00 Plate Access Guard Head End T1032/36/42 13071204016...
Page 75
PARTS DISCHARGE HEAD T852 1300060439-07-00...
Page 76
PARTS DISCHARGE HEAD T852 HARVEST by MERIDIAN T852 REF # PART # QUANTITY DESCRIPTION 13071204016 Flange Lock Bolt 1/4 x 1-20 Gr 5 1300030739-00 Guard Head End T8/10 1300010954A-00 Gasket Guard Head End T8/10 1300010306A-00 Spacer Sprocket/Bearing Head End T1032/36/42/52...
Page 77
PARTS DISCHARGE HEAD T862 1300060439-08-00...
Page 78
PARTS DISCHARGE HEAD T862 HARVEST by MERIDIAN T862 REF # PART # QUANTITY DESCRIPTION 13071204016 Flange Lock Bolt 1/4 x 1-20 Gr 5 1300030739-00 Guard Head End T8/10 1300010954A-00 Gasket Guard Head End T8/10 1300010306A-00 Spacer Sprocket/Bearing Head End T1032/36/42/52...
Page 80
PARTS FORK T8 HARVEST by MERIDIAN T8 REF # PART # QUANTITY DESCRIPTION 1300030891-00 Hitch Fork T8 1300010257-00 Pin Bent 1/2" x 5" Useable Length 1300030890-00 Fork Housing T8 1300030801-00 Bushing Brass Fork T8/10/13 13073000008 Stover Locknut 1/2-13 Type B Gr 5...
Page 82
PARTS HOPPER T8 HARVEST by MERIDIAN T8 REF # PART # QUANTITY DESCRIPTION 13073808056 Clevis Pin 1/2 x 3 1/2 1300010257-00 Pin - Bent - 1/2" x 5" Useable Length 1300010381-00 Hairpin, .093 X 1.625 13071206020 Flange Lock Bolt 3/8 x1 1/4-16 Gr 5...
Page 83
PARTS PTO DRIVE OPTION T832/36/42/52 15*** 14*** 13*** 12*** NOTE: * Items 1-4 and 6-11 does not supply with the option kit, they are part of parent hardware box. ** Qty. of Item 4 varies for T832, T836, T842, and T852. *** Items 12-15 are only for T836, T842, and T852.
Page 84
PARTS PTO DRIVE OPTION T832/36/42/52 HARVEST by MERIDIAN T832/36/42/52 QUANTITY REF # PART # DESCRIPTION 1300012529-00 Cover Chain Coupler T8/10/13 13073400008 Spring Lock Washer 1/2 13070208016 Hex Cap Screw 1/2 x 1-13 Gr 5 1300010304-00 T832: 2 Screw, Self Tapping, #12X3/4"...
Page 85
PARTS PTO DRIVE OPTION T862 NOTE: * Items 1-4 and 6-11 does not supply with the option kit, they are part of parent hardware box. 1300060439-78-00...
Page 86
PARTS PTO DRIVE OPTION T862 HARVEST by MERIDIAN T862 REF # PART # QUANTITY DESCRIPTION 1300012529-00 Cover Chain Coupler T8/10/13 13073400008 Spring Lock Washer 1/2 13070208016 Hex Cap Screw 1/2 x 1-13 Gr 5 1300010304-00 Screw, Self Tapping, #12X3/4" 1300010942-00...
Page 87
PARTS ELECTRIC DRIVE OPTION T8 22*** 20** 26*** NOTE: * Items 15-21 and 23-25 does not supply with the option kit, they are part of parent hardware box. ** Item 20 only for T836. *** Items 22 and 26 are only for T836 and T862. 1300060439-79-00...
Page 88
PARTS ELECTRIC DRIVE OPTION T8 HARVEST by MERIDIAN T8 QUANTITY REF # PART # DESCRIPTION 1300010816-00 T832/36/42/52: Belt Guard Outer Electric T832/36/42/52 1300011822-00 T862: Belt Guard Outer Electric T862 1300012963-00 T832/36/42/52: Belt, V, Drive, 2/B136 1300012965-00 T862: Belt, V, Drive, 2130 13070204012 BOLT, HEX, 1/4-20 UNC X 0.75 Steel, Mild...
Page 89
5. Title to any replaced materials Harvest by Meridian wishes to have pass to it, shall pass to Harvest by Meridian.
Page 90
Harvest by Meridian shall not be responsible for any warranty offered by the Purchaser to its customers with respect to the Goods and the Purchaser shall indemnify Harvest by Meridian with respect to same if any of those customers makes a claim against Harvest by Meridian relating to any such warranty.
Page 91
MERIDIAN MANUFACTURING INC. MERIDIAN MANUFACTURING INC. With over 65 years of experience, With over 65 years of experience, Meridian is your storage and handling expert. Meridian is your storage and handling expert. ® www.meridianmfg.com Cambridge Office Camrose Office Lethbridge Office Regina Office Storm Lake Office Winkler Office...