Related Manuals for HARVEST H1364XT
Summary of Contents for HARVEST H1364XT
- Page 1 H1364XT, H1374XT, & H1384XT AUGER ASSEMBLY MANUAL Read & understand all instructions pertaining to this auger prior to use! Revised 8/31/2015...
- Page 2 Safety Alert Watch for this ALERT Symbol. It identifies potential hazards to Personal SAFETY and your HEALTH. It points out Safety precautions. This SAFETY symbol means: ATTENTION: BE ALERT Why is SAFETY important to you? THREE BIG REASONS: *ACCIDENTS DISABLE AND KILL *ACCIDENTS COST *ACCIDENTS CAN BE AVOIDED Failure to read this Auger manual before operation of the Auger is a misuse of the...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Tube Identification ……………………………………………….. Step 1 Tube & Flighting Assembly ……………………………………………….. Steps 2-5 Discharge Head Assembly ……………………………………………….. Step 6 Cable Mount & Truss Assembly ……………………………………………….. Steps 7 & 8 Infeed Housing Assembly ……………………………………………….. Steps 9-19 Transport Arm Assembly ……………………………………………….. -
Page 4: Tube Identification
Step 1 Tube Identification Tube H1364, H1374, & H1384XT Tube H1364, H1374, & H1384XT Tube, Discharge H1364XT Tube, H1374 & H1384XT Tube, Discharge H1374XT H13XT Assembly Manual Page 4 of 33 ... -
Page 5: Step 3
& tubes as shown in Step 3. Connect the flighting using (3) 5/8" x 3” hex bolts and top lock nuts. Connect the tubes using (10) 1/2" x 1-1/2” hex flange bolts and flange nuts. If assembling an H1364XT please skip to Step 6. Fig. 4.1 H13XT Assembly Manual... -
Page 6: Discharge Head Assembly
Step 5 (H1074 & H1084 Only) Place the 4 tube in front of the 3 tube and connect the flighting as shown in Step 3. After the flighting is connected and secure, slide the 3 & 4 tube together as shown. Mount the cable attachment brackets (10680) to the left and right side of the flange on the 3 tube. -
Page 7: Cable Mount & Truss Assembly
Step 7 (Cable Mount & Truss Assembly) In Step 7 the lower cable mount brackets will be installed. On the 1 tube bolt cable mount brackets (31972) to the left & right side of the hopper arm bracket as shown. These will be fastened using (2) 5/8” x 1-1/2” flange bolts &... -
Page 8: Infeed Housing Assembly
Step 9 (Infeed Housing Assembly) Loosen bolts and remove both side access panels. Remove 5 bolts and remove the top access panel. Using a lifting strap, lift and slide the infeed housing over the bottom flighting on the 1 tube. Secure the infeed housing to the first tube using (10) 1/2"... -
Page 9: Steps
Step 10 Next, slide the 4 bolt 1-3/4” cast flange bearing over the shaft making sure the grease zerk is located on the same side as top bearing. (If the shaft has surface rust, clean first with an emry cloth) Secure the 4 bolt bearing to the infeed housing using (4) 1/2"... - Page 10 Step 12 Locate the #60 chain, #60 half link, & #60 connector link. Attach the half link to the chain on one end & place the chain around the sprockets as shown in fig. 12.1. Secure chain with connector link. When connector link is installed &...
- Page 11 Step 14 Next, install the infeed tounge assembly to the infeed housing. Secure the tongue with a 3/4" x 6” hex bolt & toplock nut through the rear of the infeed housing and the tounge tube. Next, lift the tongue up to the infeed housing and insert a 3/4"...
- Page 12 Step 16 Locate the PTO support bracket & mount it to the infeed housing as shown in fig. 16.1 using (4) 3/8” x 3/4" flange bolts & flange nuts. Attach the PTO support chain to the bracket as shown using a 3/8” x 1” flange bolt &...
-
Page 13: Transport Arm Assembly
Step 18 Next the hopper winch will be mounted. On the right side of the infeed housing attache the winch mount bracket (10131B) to the infeed housing using (4) 3/8” x 1” hex flange bolts & flange nuts. Next, mount the winch retain bracket (10251) to the winch and secure with (3) 3/8”... - Page 14 Step 20 Next the hopper lift cable will be assembled. Insert cable through the upper then the lower pulley on the hopper transport arm. Pull cable back to the winch. Insert cable through hole on the side of the winch drum. Fasten to winch using the winch cable clamp &...
-
Page 15: Truss Cable Assembly
Step 21 (Truss Cable Assembly) Take 1 long 1/2” cable & attach it to the upper eyebolt located in the middle of the first tube. Secure using (2) 1/2” cable clamps Pull cable to first truss and through a 1/2” cable clamp on the top of the truss. When the cable is through the cable clamp, continue pulling the cable to the quicklink located on the discharge end of the last tube. - Page 16 When the cable is through the cable clamp, continue pulling the cable to the quick link located on the joint on the end of the 3 tube. (This will be on the same quick link for a H1364xt) Secure using (2) 3/8" cable clamps. Repeat on opposite side of the auger.
-
Page 17: Steps
Step 23 (H1374 & H1384 Only) Locate the short 1/2” cables. Attach cable to eyebolts on the end of the 1 tube. Attach using the same process specified in step 22. Pull cable to the truss & put the cable through a cable clamp and mount to the lower mounting position on the truss as shown in fig. - Page 18 Step 25 When all the eyebolts are tightened it is now time to tighten the truss cable clamps. Tighten each cable clamp that is mounted to each truss evenly. After the clamps are tightened, stabilize the auger and lower the discharge end of the auger.
-
Page 19: Hydraulic Hose Assembly
Step 26 (Hydraulic Hose Assembly) Locate the hydraulic kit and the quarter turn shut off valve. Attach the hoses and shut off valve to the left side of the infeed housing using (3) 1/2" hose “P” clamps & (3) 1/4" x 3/4" flange bolts & nuts as shown in figure 26.1. - Page 20 Step 27 (Carriage Assembly) Carriage Identification Carriage Arm (2X) Axle Left Scissor Arm Right Scissor Arm Transport Support Tube Cylinder Cross Tube Upper Scissors H13XT Assembly Manual Page 20 of 33 ...
- Page 21 Step 28 Attach the carriage arms to the axle as shown in fig. 28.1. Fasten the carriage arms to the axle using (4) 5/8” x 1-1/2” flange bolts and nuts. Do not tighten these bolts at this time. Fig. 28.1 Step 29 Locate the cylinder cross tube assembly.
- Page 22 Step 30 Locate the right scissor arm. Attach the scissor arm to the axle using a 1-1/4” x 6-3/4” pin. Secure the pin with (2) 3/8” x 3” roll pins. (Fig. 30.1) Attach the other end of the scissor are to the cylinder cross tube as shown in fig.
- Page 23 Step 32 Next, the carriage arm spacer should be installed. Place the carriage are spacer plate between the two lower carriage arms as shown in fig. 32.1. Attach the plate to both carriage arms using (4) 1/2” x 1” flange bolts & flange nuts.
- Page 24 Step 33 Next, locate the upper scissors assembly. Place the upper scissors between the left & right scissor arms as shown in fig. 33.1. Rest the upper scissors on the transport support arm. Attach the upper scissors using 2 pins that are 9-5/8”...
- Page 25 Step 34 Now, go through the carriage and tighten all the 5/8” flange bolts & 3/4" hex bolts. Fig. 34.1 Fig. 34.2 Fig. 34.3 Step 35 Locate the 2 hydraulic cylinders (30093) & the 1-1/2” x 7-1/2” cylinder pins. Locate (4) 3/8” x 3” roll pins. Using a lifting strap, lift the first cylinder up &...
- Page 26 Step 36 Locate the (2) 1-1/2” x 6” cylinder pin & (4) 3/8” x 3” roll pins. Using the lifting strap, lift the rod end of the cylinder up to the cylinder mount cross tube. Using a punch may be needed to align the holes in the cross tube mount and the cylinder.
- Page 27 Step 38 Next, lift one side of the axle off the ground. Locate the 2 hub assemblies & 2 wheels. Attach the hub to the axle using (6) 1/2" x 1-1/2” hex flange bolts & flange nuts. Tighten these bolts. Mount the wheel on to the hub and secure using (6) 1/2"...
- Page 28 Step 40 Using a lifting strap, lift the scissor hinge part of the carriage up to the auger tube. Lift carriage up within approximately 1/4" of the auger tubes. Be sure to keep the discharge end the auger supported at this time. Lift both carriage arms up and attach to the lower carriage mount bracket using a 1-1/4”...
-
Page 29: Step
Step 42 Now, go through the carriage and insert 1/4" grease zerks into all bushing. (See pictures below) Fig. 42.1 Fig. 42.2 Fig. 42.3 Step 43 (Hydraulic Hose Assembly) First remove the plug from the top or the bore end of the cylinders. Identify the velocity fuse. Install velocity fuse into both cylinder as shown in fig. -
Page 30: Steps
Step 44 Locate the brass breathers. Install both brass breather on the lower or rod end of the cylinders. Once the brass breathers are installed tighten breather. Fig. 44.1 Step 45 (Swing Tube & Hopper Installation) Install the swing hopper knuckle (30439) on to the swing tube gearbox. Next, install the swing hopper swivel ring on the discharge head of the swing tube. - Page 31 Step 46 Next, install the flexible hose seal (13226) on to the ring and head as shown in fig. 46.1. Secure on the hose to the head and the ring with (2) hose clamps (13145). Locate the swing tube hold down plates (13195). Place swing tube on infeed housing being sure to align the swing tube knuckle and infeed gearbox.
- Page 32 Step 48 Next, install the upper transition flighting (30883) on the lower drive shaft attached to the swing tube flighting. To do this, slide a 1/4” x 1” square key into key way on swing tube flighting shaft. Slide upper transition flighting onto shaft aligning the key and keyway.
-
Page 33: Parts Book Drawings
Secure to the tube using (2) #12 x 3/4” self tapping screws. Note that they canister lid will have to be removed to install 1 of the screws. After installation, reattach the canister lid. Fig. 50.1 This will complete the assembly for your Harvest International H1364 , H134 or H1384 grain auger. - Page 34 H1364XT AUGER, BASE MODEL, H1364XT DESCRIPTION ITEM NO. PART NO. CABLE, TRUSS, 3/8" X 51FT, H1064XT, H13XT 13164 CABLE, TRUSS, 1/2" X 50FT, H1364XT 13231 HOPPER ASM, SWING, H13XX PBH13014 TUBE ASM, 1ST, H13XT PBXT13001 TUBE ASM, 2ND, H13XT PBXT13002 TUBE ASM, DISCHARGE, H1364XT &...
- Page 35 PART/ASSEMBLY DESCRIPTION MODEL(S) H1374XT AUGER, BASE MODEL, H1374XT DESCRIPTION ITEM NO. PART NO. CABLE, TRUSS, 3/8" X 51FT, H1064XT, H13XT 13164 CABLE, TRUSS, 1/2" X 43FT, H1374XT & H1384XT 13232 CABLE, TRUSS, 1/2" X 60FT, H1374XT 13233 HOPPER ASM, SWING, H13XX PBH13014 TUBE ASM, 1ST, H13XT PBXT13001...
- Page 36 CABLE, TRUSS, 1/2" X 70FT, H1384XT 13234 HOPPER ASM, SWING, H13XX PBH13014 TUBE ASM, 1ST, H13XT PBXT13001 TUBE ASM, 2ND, H13XT PBXT13002 TUBE ASM, DISCHARGE, H1364XT & H1384XT PBXT13003 TUBE ASM, 3RD, H1374XT & H1384XT PBXT13004 CARRIAGE ASM, H13XT PBXT13009 INFEED ASM, H13XT PBXT13010 DRAWING NO.
- Page 37 PART/ASSEMBLY DESCRIPTION AUGER MODEL(S) H1364XT, H1374XT, & H1384XT TUBE ASM, 1ST, H13XT DETAIL B DETAIL E DETAIL C DETAIL A DRAWING NO. PBXT13001...
- Page 38 PART/ASSEMBLY DESCRIPTION AUGER MODEL(S) H1364XT, H1374XT, & H1384XT TUBE ASM, 1ST, H13XT DESCRIPTION ITEM NO. PART NO. HAIRPIN, .093 X 1.625 10381 PIN, COTTER, .125"x1.5" 10426 5/8", OD CLAMP, GALV. VINYL, HYD HOSE RETAIN 10588A I-BOLT, FORGED 3/4" RIGHT HAND 10652 BRACKET, HOPPER TRANSPORT ARM MNT.
- Page 39 PART/ASSEMBLY DESCRIPTION MODEL(S) H1364XT, H1374XT, & H1384XT TUBE ASM, 2ND, H13XT DETAIL A DETAIL B DESCRIPTION ITEM NO. PART NO. CLAMP, 3/8" CABLE, ZINC 10303 CLAMP, CABLE, 1/2" ZINC PLATED 10367 5/8", OD CLAMP, GALV. VINYL, HYD HOSE RETAIN 10588A...
- Page 40 PART/ASSEMBLY DESCRIPTION MODEL(S) H1364XT & H1384XT TUBE ASM, DISCHARGE, H1364XT & H1384XT DETAIL A DESCRIPTION ITEM NO. PART NO. LYNCH PIN, 1/4" X 2-1/8" 10364 NUT, 1/2-20, 60 DEGREE LUG NUT, ZINC 10434 QUICKLINK CHAIN CONNECTOR, 1/2 INCH 10579 BRACKET, BOLT TRUSS CABLE MOUNT, H13XX...
- Page 41 PART/ASSEMBLY DESCRIPTION MODEL(S) H1374XT & H1384XT TUBE ASM, 3RD, H1374XT & H1384XT DETAIL B DETAIL A DESCRIPTION ITEM NO. PART NO. QUICKLINK CHAIN CONNECTOR, 1/2 INCH 10579 BRACKET, BOLT TRUSS CABLE MOUNT, H13XX 10680 FLIGHTING SECTION ASM, REGULAR, H13XX 30430 TUBE ASM, 3RD, H13XT 31960 BOLT, 1/2-13UNC X 1-1/2"...
- Page 42 PART/ASSEMBLY DESCRIPTION MODEL(S) H1374XT TUBE ASM, DISCHARGE, H1374XT DESCRIPTION ITEM NO. PART NO. LYNCH PIN, 1/4" X 2-1/8" 10364 NUT, 1/2-20, 60 DEGREE LUG NUT, ZINC 10434 QUICKLINK CHAIN CONNECTOR, 1/2 INCH 10579 BRACKET, BOLT TRUSS CABLE MOUNT, H13XX 10680 EXTENSION SPRING 11357 DISCHARGE HOUSING ASSY, H13...
- Page 43 PART/ASSEMBLY DESCRIPTION MODEL(S) H1364XT, H1374XT, & H1384XT CARRIAGE ASM, H13XT DETAIL B DETAIL A DRAWING NO. PBXT13009...
- Page 44 PART/ASSEMBLY DESCRIPTION MODEL(S) H1364XT, H1374XT, & H1384XT CARRIAGE ASM, H13XT DESCRIPTION ITEM NO. PART NO. PIN, UPPER CYLINDER, H10, 1-1/2 X 7-1/2" 10198 PIN, LOWER HYDRAULIC CYLINDER 10199 ZERK, GREASE, 1/4-28UNF, STRAIGHT 10245 PIN, ROLL, 3/8" X 3" ZINC 10384...
- Page 45 PART/ASSEMBLY DESCRIPTION MODEL(S) H1364XT - H13114XT INFEED ASM, H13XT DRAWING NO. PBXT13010...
- Page 46 PART/ASSEMBLY DESCRIPTION MODEL(S) H1364XT - H13114XT INFEED ASM, H13XT DETAIL A DRAWING NO. PBXT13010...
- Page 47 PART/ASSEMBLY DESCRIPTION MODEL(S) DESCRIPTION ITEM NO. PART NO. BRACKET, WINCH MOUNT, BOLT ON 10131B 1/2" CLAMP, GALV,VINYL,HYDRAULIC HOSE RETAIN 10151 SPROCKET, IDLER, #60, 11 TOOTH, 1/2" BORE 10300 KEY, 1/4" X 1-1/2" 10309 1/2 NPT MALE TIP, 1/2" BODYSIZE (8010-4) (PIONEER) 10324 BRACKET, PTO SHAFT SUPPORT, H13 10526A...
- Page 48 PART/ASSEMBLY DESCRIPTION MODEL(S) H1364XT - H13114XT SWING TUBE ASM, H13XT DETAIL B DRAWING NO. DETAIL A PBXT13011...
- Page 49 PART/ASSEMBLY DESCRIPTION MODEL(S) H1364XT - H13114XT SWING TUBE ASM, H13XT DESCRIPTION ITEM NO. PART NO. LYNCH PIN, 1/4" X 2-1/8" 10364 LID, ACCESS, HOPPER, H13XT 10500 PLATE, SWING TUBE RETAIN, H13XX 11790 HINGE, RUBBER, SWING TUBE, H13XT 13218 STRAP, RUBBER HINGE, SWING TUBE, H13XT...
- Page 50 AUGER MODEL(S) PART/ASSEMBLY NO. PART/ASSEMBLY DESCRIPTION H1362, H1372, H1382 HOPPER ASSEMBLY PART NOT SHOWN: QTY: (1) NO. 10571A #50 ROLLER CHAIN X 80 ROLLERS + CONNECTOR LINK replaced by part P/N 30883 Detail B DRAWING NO. PBH13014...
- Page 51 AUGER MODEL(S) PART/ASSEMBLY NO. PART/ASSEMBLY DESCRIPTION HOPPER ASSEMBLY H1362, H1372, H1382 30554 1 1-4 3 BOLT 1.25" 3 BOLT FLANGETEE WITH BEARING, STANDARD HOLE PATTERN 30442 SWING HOPPER WELDMENT, H13XX 10041 PLATE, BEARING MOUNT, SWING HOPPER 10516A GUARD, SWING HOPPER DRIVE CHAIN 10308 PIN, COTTER, 3/16x1.5"...