DSC TL2803GR Installation Manual page 52

FCC Compliance Statement
CAUTION: Changes
approved by the Digital Security Controls could void your
authority to use this equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communi-
cations. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
- Re-orient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician
for help.
The user may find the following booklet prepared by the FCC
useful: 'How to Identify and Resolve Radio/Television Interfer-
ence Problems'. This booklet is available from the U.S. Govern-
ment Printing Office, Washington D.C. 20402, Stock # 004-000-
00345-4.
Warning: To satisfy FCC RF exposure requirements for
mobile transmitting devices, a separation distance of 20cm or
more must be maintained between the antenna of this device
and persons during device operation.
Industry Canada Statement
The prefix 'IC:' in front of the radio certification number signi-
fies only that Industry Canada technical specifications were met.
Certification Number IC: 160A-3G260R
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following tow conditions:
(1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device.
or modifications not
© 2014 Tyco International Ltd. and its Respective Companies. All Rights Reserved.
Toronto, Canada
•
Tech Support: 1-800-387-3630 (CA, US), 905-760-3000
Cet appareil est conforme avec Industrie Canada exempts de
licence standard RSS (s). Le fonctionnement est soumis aux deux
expressly
conditions suivantes: (1) cet appareil ne peut pas provoquer
d'interférences et (2) cet appareil doit accepter toute interférence,
y compris les interferences qui peuvent causer un mauvais
fonctionnement de l'appareil.
This Class B digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
EN50131 Compliant Installations
1. The TL2803G(R)-EU, 3G2080(R)-EU module is monitored
by the control panel and it is programmed via the programming
menu (* 8, section [851] in the control panel. The interface is
connected to the PC-Link bus as shown in the diagram included
in this manual.
2. The Ethernet port is protected against surge transients up to
2.5kV and both Ethernet port and GPRS/3G Cellular path are
immune to conducted and radiated RF fields with levels up to
10V/m as tested per EN50130-4 Standard.
3. The TL2803G(R)-EU, 3G2080(R)-EU module conforms with
radiated emissions levels for Class B equipment as per standards
EN61000-6-3/EN55022/CISPR22.
4. The TL2803G(R)-EU, 3G2080(R)-EU module uses AES128
encryption and heartbeat supervision for both Ethernet and
GPRS/3G Cellular communication paths and it meets security
levels S2 as per EN50136-2-1 (EN50131-1). It also uses authen-
tication for each message exchanged with the compatible
receiver equipment at ARC and it meets level I2 for information
security.
5. The TL2803G(R)-EU module has two communication paths:
Ethernet 10/100BaseT and GPRS/3G Cellular communication
path that can be used in a redundant (parallel) mode or back-up
mode configuration based on selecting the appropriate option in
the programming section [851][005]. The 3G2080(R)-EU mod-
ule has only one communication path:GPRS/3G Cellular com-
munication path using 900/1800/2100MHz Public Cellular
Network.
TL2803GR-EU, TL2803G-EU, 3G2080R-EU, 3G2080-EU have
been certified by Telefication in accordance with EN50131-1
requirements for Grade 2, Class II and ATS Class 3,4,5.
www.dsc.com
2 9 0 0 8 4 3 9 R0 0 1