DSC 3G2080 Installation Manual
Cellular alarm communicator, interner and hspa dual-path alarm communicator
Hide thumbs
Also See for 3G2080:
- Installation manual (29 pages) ,
- Installation manual (52 pages) ,
- Installation manual (25 pages)
Table of Contents
Advertisement
Quick Links
3G2080(R)
Cellular Alarm Communicator – North America
TL2803G(R)
Internet and HSPA Dual-Path Alarm Communicator -
North America
I
G
4.1
NSTALLATION
UIDE V
For installation manual visit www.dsc.com
Warning: This manual contains information on limitations regarding product use
and function and information on the limitations as to liability of the manufacturer.
Advertisement
Table of Contents
Related Manuals for DSC 3G2080
Summary of Contents for DSC 3G2080
- Page 1 Internet and HSPA Dual-Path Alarm Communicator - North America NSTALLATION UIDE V For installation manual visit www.dsc.com Warning: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer.
- Page 2 WARNING: I NSTALLER LEASE AREFULLY Note to Installers Motion Detectors The warnings on this page contain vital information. As the only Motion detectors can only detect motion within the designated areas individual in contact with system users, it is the installer’s responsi- as shown in their respective installation instructions.
-
Page 3: Safety Information
Specific programming for the related programming sections is to be provided by the 3rd party. A current list of compatible 3rd party solutions can be found at www.dsc.com 3G2080(R): Is a HSPA (3G) cellular alarm communicator that sends alarm communication to Sur-Gard System I-IP, II, III (SG-DRL3IP), IV (SG-DRL4IP), and 5 (SG-DRL5IP) central station receivers via a HSPA(3G)/GPRS digital cellular network. -
Page 4: Technical Specifications
HSPA(3G)/Dual Alarm Communicator Installation Manual The following communicators are compatible with HS2016, HS2032, HS2064, and HS2128 pan- els: • 3G2080R, 3G2080 (HSPA(3G)/GPRS only) • TL2803GR, TL2803G (Internet + HSPA(3G)/GPRS dual-path) NOTE: This manual covers communicator models with and without ‘R’ throughout entire manual unless specifically stated otherwise. - Page 5 (00C8/200) seconds. For encrypted line security systems the encryption AES128 bit shall be enabled at the monitoring station receiver. • For UL Commercial Burglary installations, the 3G2080(R) is listed as a primary (sole) com- munication means (heartbeat must be enabled) or for supplementary (back-up) use in conjunc- tion with a Plain Old Telephone Service (POTS) line dialer.
-
Page 6: Ratings Compatibility
HSPA(3G)/Dual Alarm Communicator Installation Manual Ratings Compatibility Table 1: Communicator Ratings 3G2080(R) TL2803G(R) Model Cellular only Internet and Cellular Power Supply Ratings 10.8-12.5 VDC Power is supplied from the panel’s PC-Link header or a PCL-422 module in Input Voltage remote cabinet installations. In remote cabinet installations, the PCL-422 module located with the communicator is powered by either an HSM2204 or an HSM2300. -
Page 7: Inserting And Removing The Sim Card
HSPA(3G)/Dual Alarm Communicator Installation Manual • Do NOT strip off cable sheathing more than required for proper termination. • Do NOT kink/knot cable. • Do NOT crush cable with cable ties. • Do NOT untwist CAT5 pairs more than ½ in. (1.2cm). •... - Page 8 RJ-45 threaded antenna connection point at top of the panel. WARNING! - 3G2080(R)/TL2803G(R) modules are power limited. Do not route any wiring over the cir- cuit board. Maintain at least 1in. (25.4mm) separa- tion between circuit board and wiring. A minimum screw of ¼...
- Page 9 Communicator GND (Optional) NOTE: The GND connection is optional. DSC recommends connecting GND wire at both ends. 6. Perform the following steps for initial power on of the panel with communicator installed: a. Reconnect the AC power, telephone line, and battery + connector to the panel.
-
Page 10: Activating The Communicator With C24 Communications
HSPA(3G)/Dual Alarm Communicator Installation Manual Activating the Communicator with C24 Communications Installation of the 3G2080(R) or TL2803G(R) requires activation with C24 Communications in order to operate. Please contact the central station (C24 Communications Master Reseller) to con- firm the required steps to activate/program the communicator. -
Page 11: Initial Panel Programming
HSPA(3G)/Dual Alarm Communicator Installation Manual 4. Move the extension antenna to various locations while observing the two green LEDs on the panel. a. Continue to reposition the extension antenna until you receive an acceptable (minimum one green LED ON solid) signal strength. NOTE: Minimum strength is: green LED 1 flashing and yellow LED off. -
Page 12: Yellow Trouble Led
HSPA(3G)/Dual Alarm Communicator Installation Manual more information about the trouble on the communicator module refer to the panel event buffer or by accessing *2 to view the individual trouble types. OMMUNICATOR TATUS The communicator has 4 on-board LED indicators. These include 1 yellow trouble LED, 1 red net- work connection status LED, and 2 green signal strength LEDs. -
Page 13: Network Activity Leds - Red And Green(Tl2803G(R) Only)
HSPA(3G)/Dual Alarm Communicator Installation Manual NOTE: The communicator will indicate cellular trouble (yellow LED = 5 flashes) if the calcu- lated average CSQ Level is 4 or less. The communicator signal strength can be viewed remotely with C24 Communications. Network Activity LEDs - Red and Green(TL2803G(R) only) •... -
Page 14: Ethernet /Cellular Programming Options
[011] Installer Code |____| [3] Supervision Type Default (OFF). Default (CAFE) Valid range: 0000 - FFFF. |____| [4] Primary Communications Path. Default [OFF] TL2803G(R); [ON] 3G2080(R). |____|____|____|____| [012] DLS Incoming Port |____| [5] Redundant Communications Default (OFF). |____| [6] Remote Firmware Upgrade Default (ON). -
Page 15: System Test Options
HSPA(3G)/Dual Alarm Communicator Installation Manual [016] DLS Call-Up Port [035] Panel Firmware Update Begin Default (FF) Program 00 disable or FF enable. Default (0000) Valid range: 0000 - FFFF. |____|____| |____|____|____|____| [036] Panel Firmware Update Successful [020] Time Zone Default (FF) Program 00 disable or FF enable. Default (00) Valid range: 00 - 99. -
Page 16: Ethernet Receiver 2 Options
HSPA(3G)/Dual Alarm Communicator Installation Manual Ethernet Receiver 2 Options [206] Cellular Receiver 1 Domain Name Default ( ) [111] Ethernet Receiver 2 Account Code Programming not permitted on UL/ULC listed system. Default (0000000000) 32 Character ASCII characters. Valid range: 0000000001 - FFFFFFFFFE. ____________________________________ |____|____|____|____|____|____|____|____|____|____| [112] Ethernet Receiver 2 DNIS... -
Page 17: Command And Control Options
HSPA(3G)/Dual Alarm Communicator Installation Manual [226] Network Trouble Delay ______________________________________________ Default (0F) [329] SMS Phone Number 19 Valid entries from, 00 to FF. ______________________________________________ |____|____| [330] SMS Phone Number 20 Command and Control Options ______________________________________________ [331] SMS Phone Number 21 [301] Command and Control Toggle Options ______________________________________________ |____| [1] Reserved... -
Page 18: System Information (Read Only)
HSPA(3G)/Dual Alarm Communicator Installation Manual System Information (Read Only) [663] Integration Toggle Options 2 |____| [1] Integration Over Serial Port (ON) [983] Firmware Update Diagnostics Section [984] Communicator Status |____| [2] Reserved [985] Radio Initialization Status |____| [3] Integration Over Ethernet (OFF) [987] Language Version |____| [4] Reserved |____|____|... -
Page 19: Software Product License
If You do ARBITRATION - All disputes arising in connection with this not agree to the terms of this EULA, DSC is unwilling to license the Agreement shall be determined by final and binding arbitration in SOFTWARE PRODUCT to You, and You have no right to use it. - Page 20 Warranty: freight cost to the repair centre; products off and on, the user is encouraged to try to correct the interference by one which are not identified with DSC's product label and lot number or serial or more of the following measures: number;...