DSC TL280R Installation Manuals
Internet alarm communicator international
Hide thumbs
Also See for TL280R:
- Installation manual (16 pages) ,
- Installation manual (16 pages) ,
- Installation manual (28 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Installation Manual
Advertisement
Table of Contents
Related Manuals for DSC TL280R
Summary of Contents for DSC TL280R
- Page 1 TL280(R) Internet Alarm Communicator - International NSTALLATION UIDE V For installation manual visit www.dsc.com Warning: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer.
- Page 3 WARNING: I NSTALLER LEASE AREFULLY Note to Installers Motion Detectors The warnings on this page contain vital information. As the only Motion detectors can only detect motion within the designated areas individual in contact with system users, it is the installer’s responsi- as shown in their respective installation instructions.
-
Page 4: Safety Information
• Do not stay close to the equipment during device operation. Model Information This manual covers the following model of alarm communicator: TL280 and TL280R. References to model TL280(R) throughout this manual applies to all specified models unless stated differ- ently. -
Page 5: Technical Specifications, Ratings And Compatibility
General Internet Alarm Communicator Installation Guide EN50131-1 Installation Requirements For EN50131-1 compliant installations, the following programming options shall be set as described. Supervision Heartbeat (required for ATS4 and ATS5): • [851][004] set to 0087h (135s heartbeat). NOTE: The compatible receiver at ARC location shall have supervision window programmed for 1800s (ATS4) or 180s (ATS 5). -
Page 6: Communicator Installation Configuration
Communicator Installation Configuration Internet Alarm Communicator Installation Guide OMMUNICATOR NSTALLATION ONFIGURATION This Ethernet Communicator shall be installed by service persons only (service person is defined as a person having the appropriate technical training and experience necessary to be aware of haz- ards to which that person may be exposed to in performing a task and can also take measures to minimize the risks to that person or other persons). - Page 7 3rd Party Device Communicator GND (Optional) NOTE: The GND connection is optional. DSC recommends connecting GND wire at both ends. Install Network Cable 1. Route the CAT 5 Ethernet cable through back of the panel and plug it into the communicator’s RJ45 jack.
-
Page 8: Status Leds
Initial Panel Programming Internet Alarm Communicator Installation Guide NITIAL ANEL ROGRAMMING HS2016/2032/2064/2128 Initial Programming Please refer to the panel manual section ‘Alternate Communicator Set-up’ for details. 1. In panel section [377] ‘Communication Variables’, subsection [002] ‘Communication Delays’, sub-subsection [1] ‘Communication Delay’, program 060 (seconds). 2. -
Page 9: Communicator Troubleshooting
Communicator Troubleshooting Internet Alarm Communicator Installation Guide • Once quickly for outgoing Ethernet transmission. • Twice quickly to indicate incoming Ethernet ACK/NACK. OFF: This is the normal state of the red network connection status LED. There are no network connection issues present. ON: There is a problem with the Ethernet network connection. -
Page 10: Programming Options
Ethernet Programming Worksheets Internet Alarm Communicator Installation Guide THERNET ROGRAMMING ORKSHEETS System Options [015] DLS Call-Up IP [001] Ethernet IP Address Default (000.000.000.000) Default (000.000.000.000) |____|____|____||____|____|____||____|____|____||____|____|____| |____|____|____||____|____|____||____|____|____||____|____|____| [016] DLS Call-Up Port [002] Ethernet IP Subnet Mask Default (0000) Valid range: 0000 - FFFF. Default (255.255.255.000) |____|____|____|____| |____|____|____||____|____|____||____|____|____||____|____|____|... -
Page 11: Ethernet Receiver 1 Options
Ethernet Programming Worksheets Internet Alarm Communicator Installation Guide Ethernet Receiver 2 Options [036] Panel Firmware Update Successful [111] Ethernet Receiver 2 Account Code Default (FF) Program 00 disable or FF enable. Default (0000000000) |____|____| Valid range: 0000000001 - FFFFFFFFFE. [037] Panel Firmware Update Fail |____|____|____|____|____|____|____|____|____|____| Default (FF) Program 00 disable or FF enable. -
Page 12: System Information (Read Only)
Ethernet Programming Worksheets Internet Alarm Communicator Installation Guide System Information (Read Only) [983] Firmware Update Diagnostics Section [984] Communicator Status [987] Language Version [988] DNS 1 IP Address |____|____|____||____|____|____||____|____|____||____|____|____| [989] DNS 2 IP Address |____|____|____||____|____|____||____|____|____||____|____|____| [990] Boot Loader Version |____|____|____|____|____|____|____|____| [991] Firmware Version |____|____|____|____|____|____|____|____| [992] Ethernet IP Address... - Page 13 Access cards or tags returned for replacement under warranty will be credited or replaced at DSC's option. Products not covered by this warranty, or otherwise out of warranty due to age, misuse, or damage shall be evaluated, and a repair esti-...
- Page 14 If You do erned by the laws of the Province of Ontario, Canada. not agree to the terms of this EULA, DSC is unwilling to license the ARBITRATION - All disputes arising in connection with this SOFTWARE PRODUCT to You, and You have no right to use it.
-
Page 15: Fcc Compliance Statement
NMB-003 du Canada. EN50131 Compliant installations 1. The TL280R, TL280 module is monitored by the control panel and it is programmed via the programming menu (* 8, section [851] in the control panel. The interface is connected to the PC- Link bus as shown in the diagram included in this manual. - Page 16 2 9 0 0 8 7 2 9 R0 0 1 © 2014 Tyco International Ltd. and its Respective Companies. All Rights Reserved. Toronto, Canada www.dsc.com • Tech Support: 1-800-387-3630 (CA, US), 905-760-3000...