Danfoss MCA 194 Operating Instructions Manual page 27

Parameter Mapping Lists
VLT 5000 series
Parameter 311 Terminal 54,
Analogue Input
Voltage
Options [0] No Operation
[1] Reference
[2] Torque limit
[3] Thermistor
[4] Relative
reference
[5] Max. torque
frequency
Table 5.98 Conversion of Parameter 311
VLT 5000 series
Parameter 312 Terminal 54, min.
scaling
Range 0 – 10.0 Volt
Table 5.99 Conversion of Parameter 312
VLT 5000 series
Parameter 313 Terminal 54, max.
scaling
Range 0 – 10.0 Volt
Table 5.100 Conversion of Parameter 313
MG37E102
Operating Instructions
FC 302 series
3-16 Reference 2
Source
7-00 Speed PID
Feedback Source
4-20 Torque Limit
Factor Source
1-93 Thermistor
Source
4-21 Speed Limit
Factor Source
Par. 3-16 Reference
resource 2 set to [0]
No function
Par. 3-16 Reference
resource 1 set to [2]
Analog input 53
Par. 4-20 Torque
Limit Factor Source
set to [6] Analog in
54
Par. 1-93 Thermistor
Ressource set to [2]
Analog input 54
Not supported
Par. 4-21 Speed
Limit Factor Source
set to [6] Analog in
54
FC 302 series
6-20 Terminal 54 Low
Voltage
-10.00 – Par. 6-21
FC 302 series
6-21 Terminal 54 High
Voltage
Par. 6-20 - 10.00 Volt
Danfoss A/S © Rev. 2014-03-06 All rights reserved.
VLT 5000 series FC 302 series
Parameter 314 Terminal 60, 3-17 Reference 3 Source
Analogue Input 7-00 Speed PID Feedback Source
current 1-93 Thermistor Source
4-20 Torque Limit Factor Source
Options [0] No Par. 3-17 Reference resource 3 set
Operation to [0] No function
[1] Reference Par. 3-17 Reference resource 3 set
to [2] Analog input 54 Par. 7-00
Speed PID
Feedback Source set to [7] Analog
input 54
[2] Feedback Par. 7-00 Speed PID Feedback
signal Source set to [7] Analog input 54
[3] Torque limit Par. 3-17 Reference resource 3 set
to [2] Analog input 54 Par. 4-20
Torque Limit
Factor Source set to [6] Analog in
54
[4] Relative Not supported
reference
Comments The HW switch S202 for analogue input 54 must be
set to current (ON).
Table 5.101 Conversion of Parameter 314
VLT 5000 series
Parameter 315 Terminal 60, min.
scaling
Range 0.0 – 20.0 mA
Table 5.102 Conversion of Parameter 315
VLT 5000 series
Parameter 316 Terminal 60, max.
scaling
Range 0.0 – 20.0 mA
Table 5.103 Conversion of Parameter 316
VLT 5000 series FC 302 series
Parameter 317 Time Out 6-00 Live Zero Timeout Time
Range 0 – 99 sec 0 – 99 sec
Table 5.104 Conversion of Parameter 317
FC 302 series
6-22 Terminal 54 Low
Current
0.00 – Par. 6-23
FC 302 series
6-23 Teminal 54 High
Current
Par. 6-22 - 20.00 mA
25
5 5