Table of Contents
Advertisement
Parameter Mapping Lists
VLT 5000 series
Parameter 114 Load compensation at
high speed
Range
0 – 300%
Table 5.33 Conversion of Parameter 114
VLT 5000 series
Parameter
115 Slip Compensation
Range
-500 - 500%
Table 5.34 Conversion of Parameter 115
5
5
VLT 5000 series
Parameter 116 Slip Compensation
Time constant
Range
0.05 – 1.00 s
Table 5.35 Conversion of Parameter 116
VLT 5000 series
Parameter 117 Resonance
dampening
Range
0 - 500%
Table 5.36 Conversion of Parameter 117
VLT 5000 series
Parameter 118 Resonance
dampening time
constant
Range
5 – 50 ms
Table 5.37 Conversion of Parameter 118
VLT 5000 series
Parameter
119 High starting torque
Table 5.38 Conversion of Parameters 119
Parameter
Option
Table 5.39 Conversion of Parameter 120
18
Operating Instructions
FC 302 series
1-61 High Speed Load
Compensation
0 – 300%
FC 302 series
1-62 Slip Compensation
-500 - 500%
FC 302 series
1-63 Slip Compensation
Time Constant
0.05 – 5.00 s
FC 302 series
1-64 Resonance
Dampening
0 - 500%
FC 302 series
1-65 Resonance
Dampening Time Constant
5 – 50 ms
FC 302 series
Not converted
VLT 5000 series
FC 302 series
120 Start delay
1-71 Start Delay
0.0 – 10.0 s
0.0 – 10.0 s
Danfoss A/S © Rev. 2014-03-06 All rights reserved.
VLT 5000 series
Parameter 121 Start function
Options
[0] DC hold in start delay
time
[1] DC brake in start delay
time
[2] Coasting in start delay
time
[3] Start frequency/voltage
clockwise
[4] Start frequency/voltage in
reference direction
[5] VVC
+
clockwise
Table 5.40 Conversion of Parameter 121
VLT 5000 series
Parameter
122 Function at stop
Options
[0] Coasting
[1] DC hold
[2] Motor check
[3] Pre-magnetizing
Table 5.41 Conversion of Parameter 122
VLT 5000 series
Parameter 123 Min frequency for
function at stop
Range
0.0 – 10.0 Hz
Table 5.42 Conversion of Parameter 123
VLT 5000 series
Parameter 124 DC holding
current
Range
0 - 100%
Table 5.43 Conversion of Parameter 124
VLT 5000 series
Parameter 125 DC braking current
Range
0 - 100%
Table 5.44 Conversion of Parameter 125
VLT 5000 series
Parameter
126 DC braking time
Range
0.0 – 60.0 s
Table 5.45 Conversion of Parameter 126
FC 302 series
1-72 Start Function
[0] DC hold/delay time
[1] DC Brake/delay
time
[2] Coast/delay time
[3] Start speed cw
[4] Horizontal
operation
[5] VVC
+
/Flux
clockwise
FC 302 series
1-80 Function at Stop
[0] Coast
[1] DC hold
[2] Motor check
[3] Pre-magnetizing
FC 302 series
1-82 Min Speed for
Function at Stop [Hz]
0.0 – 20.0 Hz
FC 302 series
2-00 DC Hold/Preheat
Current
0 - 160% (motor depending)
FC 302 series
2-01 DC Brake Current
0 – 160% P.U depending
FC 302 series
2-02 DC Braking Time
0.0 – 60.0 s
MG37E102
Advertisement
Table of Contents
