JVC GY-DV5000U Service Manual page 20

Error code Display
0201 CONDENSATION ON DRUM
3200 LOADING FAILURE
3300 UNLOADING FAILURE
No display
4100 CASSETTE EJECT FAILURE
5605 DEFECTIVE TAPE
5606 DEFECTIVE TAPE
5607 DEFECTIVE TAPE
5608 DEFECTIVE TAPE
5609 DEFECTIVE TAPE
5702 TAPE END DET. ERROR
5802 TAPE BEGIN DET. ERROR
7001 DRUM MOTOR FAILURE
7101 CAP MOTOR FAILURE
7202 SUPPLY REEL FAILURE
7203 SUPPLY REEL FAILURE
7302 TAKE UP REEL FAILURE
7303 TAKE UP REEL FAILURE
7305 TAKE UP REEL FAILURE
7401 REEL MOTOR FAILURE
1-16
Content of occurrence Method of detection
DEW detected If DEW sensor detects
condensation
Does not load If mechanism position does
not move in loading direction
within 5 seconds
Does not unload If mechanism position does
not move in unloading
direction within 5 seconds
Does not intake If intake is not completed
within 5 seconds (Ejects
without warning)
Does not eject If eject is not completed
within 5 seconds
Tape abnormality If begin or end side sensor is
during intake ON after intake
Tape tear during If reel FG is excessive during
unloading unloading
Tape tear during If reel FG is insufficient during
loading loading
Tape tear on the If only supply side reel does
loading side not rotate during FWD/REV
Tape tear during If tape slack takeup is not
slack takeup completed within 10 seconds
End sensor If trailer tape sending is not
abnormality completed within 3 seconds
Begin sensor If leader tape sending is not
abnormality completed within 3 seconds
Drum motor does If drum motor does not rotate
not rotate for over 4 seconds
Capstan motor If capstan motor does not
does not rotate rotate for over 2 seconds
SUP reel does not If SUP reel does not rotate for
rotate over 3 seconds
SUP side tape slack If only SUP reel does not
rotate during REV
TU reel does not If TU reel does not rotate for
rotate over 3 seconds
TU side tape slack If only TU reel does not rotate
during FWD
Tape slack during If TU reel FG is insufficient
unloading during unloading
Reel motor does If reel motor does not rotate
not rotate for more than 4 seconds
during reel drive mode
Table 1-9-11 (3) Error Code Contents
Detected signal
IC302 (MSD) –detects
voltage of pin 318
IC302 (MSD) –detects output
of pin 354, rotary encoder
IC302 (MSD) –detects output
of pin 354, rotary encoder
IC302 (MSD) –pin 84,
CASSETTE SW is not
detected within 5 seconds
IC302 (MSD) –pin 26,
HOUSING SW is not
detected within 5 seconds
IC302 (MSD) –pin 278, START
sensor and pin 297,
END sensor are both detected
IC302 (MSD) –pin 75, TU
REEL FG is detected
IC302 (MSD) –pin 75, TU
REEL FG is detected
IC302 (MSD) –pin 72, SUP
REEL FG is not detected
IC302 (MSD) –pin 75, TU
REEL FG and pin 72, SUP
REEL FG are both detected
IC302 (MSD) –pin 297, END
sensor is detected for over 3
seconds
IC302 (MSD) –pin 278,
START sensor is detected for
over 3 seconds
IC302 (MSD) –pin 55, DRUM
FG is not detected for over 4
seconds
IC302 (MSD) –pin 56, CAP
FG is not detected for over 2
seconds
IC302 (MSD) –pin 72, SUP
REEL FG is not detected for
over 3 seconds
IC302 (MSD) –pin 72, SUP
REEL FG is not detected
IC302 (MSD) –pin 75, TU
REEL FG is not detected for
over 3 seconds
IC302 (MSD) –pin 75, TU
REEL FG is not detected
IC302 (MSD) –pin 75, TU
REEL sensor is detected
IC302 (MSD) –pin 91, REEL
FG is not detected for over 4
seconds