GE N60 Instruction Manual page 431

CHAPTER 5: SETTINGS
DIRECT INPUT 15 BIT NUMBER
DIRECT INPUT 16 DEVICE ID
DIRECT INPUT 16 BIT NUMBER
DIRECT INPUT 17 DEVICE ID
DIRECT INPUT 17 BIT NUMBER
2. The remote power is available as the
significant bit) and
DIRECT INPUT 17 On
For the 8-Bit Comparator at UR-2
1. Remote power from UR-1 IED received on direct inputs is the first argument for the comparator. As such, apply the
following settings:
: "DIRECT INPUT 1 On"
8 BIT COMP 1 ARG A0
: "DIRECT INPUT 5 On"
8 BIT COMP 1 ARG A4
: "DIRECT INPUT 2 On"
8 BIT COMP 1 ARG A1
: "DIRECT INPUT 6 On"
8 BIT COMP 1 ARG A5
: "DIRECT INPUT 3 On"
8 BIT COMP 1 ARG A2
: "DIRECT INPUT 7 On"
8 BIT COMP 1 ARG A6
: "DIRECT INPUT 4 On"
8 BIT COMP 1 ARG A3
: "DIRECT INPUT 8 On"
8 BIT COMP 1 ARG A7
2. Local power from the UR-2 IED available internally is the second argument for the comparator. Thus, apply the
following settings:
: "DIGITIZER 1 BIT 0"
8 BIT COMP 1 ARG B0
: "DIGITIZER 1 BIT 4"
8 BIT COMP 1 ARG B4
: "DIGITIZER 1 BIT 1"
8 BIT COMP 1 ARG B1
: "DIGITIZER 1 BIT 5"
8 BIT COMP 1 ARG B5
: "DIGITIZER 1 BIT 2"
8 BIT COMP 1 ARG B2
: "DIGITIZER 1 BIT 6"
8 BIT COMP 1 ARG B6
: "DIGITIZER 1 BIT 3"
8 BIT COMP 1 ARG B3
: "DIGITIZER 1 BIT 7"
8 BIT COMP 1 ARG B7
3. The two power values are to be added, therefore set
4. To establish the alarm when the total power in either direction (import or export) is above the threshold, set
to "Absolute."
1 INPUT MODE
5. To establish the alarm when the total power is above the threshold, set the
6. The digitized power values are scaled to meaningful values. Assuming that MW are to be used for comparison and
display, set
8BIT COMP 1 SCALE FACTOR
actual values represent the remote (UR-1), local (UR-2), and total power values in MW.
7. To set the alarm when the total power is greater than 2500 MW, set
8. To clear the alarm when the total power is less than 2000 MW, the hysteresis setting needs to be at 2500 – 2000 = 500
MW. So set
8BIT COMP 1 HYSTERESIS
9. Using the timing requirements, set
the FlexLogic operand to set the alarm.
8BIT COMP 1 OP
10. For monitoring and telemetry purposes, the digitized power values need to be scaled to meaningful values. Assuming
MW to be displayed, set
8BIT COMP 1 SCALE FACTOR
and represent the remote (UR-1), local (UR-2), and total power values in MW.
B 8BIT COMP 1 Out
For the User-definable displays at UR-2 (optional)
To display the remote and total power values the following screen can be set up:
: "REMOTE MW: ~"
DISP 1 TOP LINE
: "TOTAL MW: ~"
DISP 1 BOTTOM LINE
: "8100" (Modbus register address of
DISP 1 ITEM 1
: "8104" (Modbus register address of
DISP 1 ITEM 2
N60 NETWORK STABILITY AND SYNCHROPHASOR MEASUREMENT SYSTEM – INSTRUCTION MANUAL
: "6"
: "1"
: "7"
: "1"
: "8"
DIRECT INPUT 10 On
(the sign bit) FlexLogic operands.
8BIT COMP 1 ADD/SUB
to "11.81". In this way, the
to "500".
8BIT COMP 1 PICKUP DELAY
to "11.81". In this way, the actual values
8BIT COMP 1 A
8BIT COMP 1 Out
(the least significant bit) through
to "On".
8BIT COMP 1 DIRECTION
,
8BIT COMP 1 A 8BIT COMP 1 B
8BIT COMP 1 PICKUP
to "0.050" and
8BIT COMP 1 RESET DELAY
)
)
CONTROL ELEMENTS
(the most
DIRECT INPUT 16 On
8BIT COMP
to "Over."
, and
8BIT COMP 1 Out
to "2500.00".
to "1.000". Use
,
8BIT COMP 1 A 8BIT COMP 1
5-271
5