GE N60 Instruction Manual page 328

FLEXLOGIC
Operand type
RxGOOSE Boolean
Virtual Input
Virtual Output
The following table lists the operands available for the relay. The operands can be viewed online by entering the IP address
of the relay in a web browser and accessing the Device Information Menu.
Table 5-24: N60 FlexLogic operands
Operand type
CONTROL
PUSHBUTTONS
CYBERSENTRY
5
DIRECT DEVICES
DIRECT INPUT/
OUTPUT CHANNEL
MONITORING
ELEMENT:
Eight-bit comparator
ELEMENT:
Eight-bit switch
5-168
State Example of format
On RxGOOSE Boolean 1 On
On Virt Ip 1 On
On Virt Op 1 On
Operand syntax
CONTROL PUSHBTN 1 ON
CONTROL PUSHBTN 2 ON
CONTROL PUSHBTN 3 ON
CONTROL PUSHBTN 4 ON
CONTROL PUSHBTN 5 ON
CONTROL PUSHBTN 6 ON
CONTROL PUSHBTN 7 ON
ROLE ADMIN ACT
ROLE SUPERVISOR ACT
ROLE ENGINEER ACT
ROLE OPERATOR ACT
ROLE OBSERVER ACT
AUTHENTICATION FAIL
UNAUTH FW ATTEMPT
UNAUTH SETTING WRITE
DIRECT DEVICE 1On
↓
DIRECT DEVICE 16On
DIRECT DEVICE 1Off
↓
DIRECT DEVICE 16Off
DIR IO CH1 CRC ALARM
DIR IO CH2 CRC ALARM
DIR IO CH1 UNRET ALM
DIR IO CH2 UNRET ALM
8BIT COMP 1 PKP
8BIT COMP 1 DPO
8BIT COMP 1 OP
8BIT COMP 1 BIT 0
8BIT COMP 1 BIT 1
8BIT COMP 1 BIT 2
8BIT COMP 1 BIT 3
8BIT COMP 1 BIT 4
8BIT COMP 1 BIT 5
8BIT COMP 1 BIT 6
8BIT COMP 1 BIT 7
8BIT COMP 2 to 6
8BIT SWITCH 1 BIT 0
8BIT SWITCH 1 BIT 1
8BIT SWITCH 1 BIT 2
8BIT SWITCH 1 BIT 3
8BIT SWITCH 1 BIT 4
8BIT SWITCH 1 BIT 5
8BIT SWITCH 1 BIT 6
8BIT SWITCH 1 BIT 7
8BIT SWITCH 2 to 6
N60 NETWORK STABILITY AND SYNCHROPHASOR MEASUREMENT SYSTEM – INSTRUCTION MANUAL
Characteristics
[Input Is '1' (= ON) if...]
The RxGOOSE Boolean is presently in the ON state
The virtual input is presently in the ON state
The virtual output is presently in the set state (that is,
evaluation of the equation that produces this virtual output
results in a "1")
Operand description
Control pushbutton 1 is being pressed
Control pushbutton 2 is being pressed
Control pushbutton 3 is being pressed
Control pushbutton 4 is being pressed
Control pushbutton 5 is being pressed
Control pushbutton 6 is being pressed
Control pushbutton 7 is being pressed
Administrator role is active and is set to true when that is the case
Supervisor role is active and is set to true when that is the case
Engineer role is active and is set to true when that is the case
Operator role is active and is set to true when that is the case
Observer role is active and is set to true when that is the case
Operand set for Failed Authentication self-test and alarm
Operand set for firmware lock self-test and alarm
Operand set for settings lock self-test and alarm
Flag is set, logic=1
↓
Flag is set, logic=1
Flag is set, logic=1
↓
Flag is set, logic=1
The rate of direct input messages received on channel 1 and failing the CRC
exceeded the user-specified level
The rate of direct input messages received on channel 2 and failing the CRC
exceeded the user-specified level
The rate of returned direct input/output messages on channel 1 exceeded
the user-specified level (ring configurations only)
The rate of returned direct input/output messages on channel 2 exceeded
the user-specified level (ring configurations only)
Comparator 1 has picked up
Comparator 1 has dropped out
Comparator 1 has operated
Bit 0 of comparator 1 asserted (the least significant bit)
Bit 1 of comparator 1 asserted
Bit 2 of comparator 1 asserted
Bit 3 of comparator 1 asserted
Bit 4 of comparator 1 asserted
Bit 5 of comparator 1 asserted
Bit 6 of comparator 1 asserted (the most significant bit)
Sign bit of comparator 1 asserted (asserted for negative values; de-asserted
for positive values)
Same set of operands as shown for 8 BIT COMP 1
Bit 0 of eight-bit switch 1 asserted (the least significant bit)
Bit 1 of eight-bit switch 1 asserted
Bit 2 of eight-bit switch 1 asserted
Bit 3 of eight-bit switch 1 asserted
Bit 4 of eight-bit switch 1 asserted
Bit 5 of eight-bit switch 1 asserted
Bit 6 of eight-bit switch 1 asserted
Bit 7 of eight-bit switch 1 asserted (the most significant bit)
Same set of operands as shown for 8 BIT SWITCH 1
CHAPTER 5: SETTINGS