Danfoss AKD 5001 Manual page 87

bit 12 to relay 04. If parameter 514 Bus time interval
function is active, relays 01 and 04 will be voltage-free.
Extended mechanical brake control: Not used in AKD.
Safety interlock The output is active when Safety
interlock has been selected on an input and
the input is a logic "1".
0-100 Hz ⇒ 0-20 mA and
0-100 Hz ⇒ 4-20 mA and
0-100 Hz ⇒ 0-32000 p, a pulse output
signal proportional to the output frequency
in the range 0-100 Hz.
0-f ⇒ 0-20 mA and
MAX
0-f ⇒ 4-20 mA and
MAX
0-f 0-32000 p, an output signal proportional
⇒
MAX
to the output frequency range in the range
0 - f (parameter 202).
MAX
Ref - Ref 0-20 mA and
⇒
MIN MAX
Ref - Ref ⇒ 4-20 mA and
MIN MAX
Ref - Ref ⇒ 0-32000 p, an output signal
MIN MAX
proportional to the reference value in the interval Ref
- Ref (parameters 204/205) is obtained.
MAX
B -FB ⇒ 0-20 mA and
MIN MAX
FB -FB 4-20 mA and
⇒
MIN MAX
FB -FB ⇒ 0-32000 p, an output signal
MIN MAX
proportional to the feedback value in the interval FB
-FB (parameters 414/415) is obtained.
MAX
0 - I ⇒ 0-20 mA or
VLT, MAX
0 - I ⇒ 4-20 mA and
VLT, MAX
0 - I 0-32000 p, an output signal proportional
⇒
VLT, MAX
to the output current in the interval 0 - I
is obtained. I depends on the settings in
VLT,MAX
parameter 101 and 103 and can be seen from
the Technical data (I
VLT,MAX
0 - M ⇒ 0-20 mA and
LIM
0 - M 4-20 mA and
⇒
LIM
0 - M ⇒ 0-32000 p, an output proportional to
LIM
the output torque in the interval 0 - T
221) is obtained. 20 mA corresponds to the
value set in parameter 221.
0 - M 0-20 mA and
⇒
NOM
0 - M 4-20 mA and
⇒
NOM
0 - M ⇒ 0-32000 p, an output signal proportional
NOM
to the output torque of the motor. 20 mA corresponds
to the rated torque for the motor.
0 - P ⇒ 0-20 mA and
NOM
0 - P ⇒ 4-20 mA and
NOM
= factory setting. () = display text [] = value for use in communication via serial communication port
86
MIN
MIN
VLT,MAX
(60 s).
(parameter
LIM
AKD 5000
0 - P ⇒ 0-32000 p, 0 - P
NOM
an output signal proportional to the rated motor
output is obtained. 20 mA corresponds to the
value set in parameter 102.
0 - SyncRPM ⇒ 0-20 mA and
0 - SyncRPM ⇒ 4-20 mA and
0 - SyncRPM 0-32000 p, an output signal
⇒
proportional to the synchronous motor RPM is obtained.
0 - RPM at F ⇒ 0-20 mA and
MAX
0 - RPM at F 4-20 mA and
⇒
MAX
0 - RPM at F 0-32000 p, n output signal
⇒
MAX
proportional to the synchronous motor RPM at
F (parameter 202) is obtained.
MAX
⇒ 0-32000 p,
NOM
MG.50.R3.02 -