HEIDENHAIN TNC 620 User Manual page 486

Index
Index
3
3D Touch Probes...................... 288
3-D touch probes....................... 42
A
Automatic datum setting.......... 320
At center of 4 holes............... 362
Center of a bolt hole circle..... 356
Center of a circular pocket
(hole)...................................... 338
Center of a circular stud......... 343
Center of a rectangular
pocket.................................... 331
Center of a rectangular stud... 335
In any axis.............................. 366
Inside of corner...................... 352
In the touch probe axis........... 360
Outside of corner................... 347
Ridge center.......................... 328
Slot center............................. 324
Automatic tool measurement... 470
Axis-specific scaling................. 265
B
Back boring................................ 79
Basic rotation
Measure during program run.. 298
Bolt hole circle......................... 163
Bore milling................................ 86
Boring......................................... 73
C
Centering................................... 67
Circular pocket
Roughing+finishing................ 137
Circular point patterns.............. 163
Circular slot
Roughing+finishing................ 145
Circular stud............................. 154
Classification of results............ 377
Compensating workpiece
misalignment............................ 298
By measuring two points on a
straight line............................ 300
Over two circular studs.......... 306
Over two holes...................... 303
Via rotary axis................ 309, 313
Confidence interval.................. 293
Consideration of basic rotation. 288
Contour cycles......................... 172
Contour train............................ 189
Coordinate transformation........ 252
Cycle.......................................... 46
Calling...................................... 48
Define...................................... 47
Cycles and point tables.............. 63
486
Cylinder surface
Machine contour.................... 203
Ridge machining..................... 209
Slot machining........................ 206
D
Datum shift.............................. 253
In the program....................... 253
With datum tables................. 254
Deepened starting point with
drilling.................................. 85, 90
Drilling............................ 69, 76, 82
Deepened starting point..... 85, 90
Drilling Cycles............................ 66
Dwell time................................ 277
E
Engraving................................. 284
F
Face milling.............................. 237
FCL function................................ 9
Feature Content Level.................. 9
Floor finishing........................... 186
Fundamentals of Thread
Milling...................................... 107
H
Helical thread drilling/milling..... 121
I
Inside thread milling................. 109
K
Kinematic measurement
Accuracy................................. 445
Backlash................................. 447
Calibration methods.... 446, 459,
461
Hirth coupling......................... 443
Logging function..... 438, 453, 463
Measuring point selection.... 439,
444
Measuring position selection. 445
Prerequisites.......................... 436
Kinematics measurement........ 434
Kinematics Measurement
Measure kinematics....... 440, 454
Kinematics measurement
Save kinematics..................... 437
KinematicsOpt.......................... 434
L
Linear point patterns................ 166
M
Machine parameters for 3D touch
probe........................................ 291
Machining pattern...................... 54
Measure angle......................... 382
Measure angle of a plane......... 410
Measure any coordinate........... 404
Measure bolt hole circle........... 407
Measure hole........................... 385
Measure hole inside................. 385
Measure hole outside.............. 388
Measure kinematics................. 440
Preset compensation............. 454
Measurement parameters........ 377
Measurement results in Q
parameters............................... 377
Measure rectangular pocket..... 395
Measure rectangular stud........ 391
Measure the plane angle.......... 410
Measure the slot width............ 398
Measure the width of a
ridge................................. 401, 401
Measuring slot width............... 398
Measuring the width of a ridge 401
Mirroring................................... 260
Multiple measurements........... 293
O
Outside thread milling.............. 125
P
Pattern definition........................ 54
Peck drilling.......................... 82, 89
Deepened starting point..... 85, 90
Point patterns........................... 162
Overview................................ 162
Point tables................................ 61
Positioning logic....................... 294
Probing feed rate..................... 292
Program call............................. 278
Via cycle................................. 278
R
Reaming..................................... 71
Recording measurement results....
375
Rectangular pocket
Roughing+finishing................ 133
Rectangular stud...................... 150
Rotation.................................... 262
Roughing:See SL Cycles,
Roughing.................................. 183
Ruled surface........................... 233
S
Scaling...................................... 264
Set a basic rotation.................. 312
Side finishing............................ 187
Single-lip deep-hole drilling......... 89
SL Cycles......................... 172, 203
Contour cycle......................... 174
Contour data.......................... 179
Contour train.......................... 189
Floor finishing......................... 186
TNC 620 | User's Manual Cycle Programming | 3/2014