PR 9203 Manual page 25

Modul 9203B1A & 9203B1B
Terminal 41-42 / 51-52
Uo 28 V IIC
Io 93 mA IIB
Po 0.65 W IIA
Modul 9203B1A & 9203B1B
Terminal 41-43 / 51-53
Uo 28 V IIC
Io 100 mA IIB
Po 0.70 W IIA
Modul 9203B1A & 9203B1B
Terminal 41-44 / 51-54
Uo 28 V IIC
Io 110 mA IIB
Po 0.77 W IIA
Terminal (31,32)
Supply:
Voltage
Power max.
Terminal (33,34)
Status Relay:
Voltage max.
Power max.
Current max.
Installation notes.
For installation in Zone 2, the module must be installed in an outer enclosure having an IP protection
of at least IP54 according to type of protection Ex-n or Ex-e.
For installation on Power Rail in Zone 2, only Power Rail type 9400 supplied by Power Control Unit
type 9410 is allowed.
In type of protection "intrinsic safety iD" the parameters for intrinsic safety for gas group IIB are
applicable.
If the sensor circuits (Terminals 41...44, 51...54) have been installed in a type of protection other than
"intrinsic safety", the module shall not be re-installed in type of protection "intrinsic safety".
Do not separate connectors when energized and an explosive gas mixture is present.
Do not mount or remove modules from the Power Rail when an explosive gas mixture is present.
The maximum internal Power dissipation for adjacent modules is assumed to be max. 2 W each.
Revision date:
2009-12-10
CONTENTS SOMMAIRE INHALT CONTENIDOS Содержание
INDHOLD
Co Lo Lo/Ro
80 nF 4.2 mH 54 μH/Ω
640 nF 16.8 mH 218 μH/Ω
2.1 μF 32.6 mH 436 μH/Ω
Co Lo Lo/Ro
80 nF 3.5 mH 50 μH/Ω
640 nF 14.2 mH 201 μH/Ω
2.1 μF 27.6 mH 402 μH/Ω
Co Lo Lo/Ro
80 nF 2.9 mH 46 μH/Ω
640 nF 11.8 mH 184 μH/Ω
2.1 μF 22.8 mH 369 μH/Ω
19.2 – 31.2 VDC
3.5 W
Non Hazardous location
125 VAC / 110 VDC
62.5 VA / 32 W
0.5 AAC / 0.3 ADC
Version Revision
V3 R0
9203 - Product Version 9203-001
Modul 9203B2A
Terminal 41-42
Uo 28 V IIC 80 nF
Io 115 mA IIB 640 nF
Po 0.81 W IIA 2.1 μF
Modul 9203B2A
Terminal 41-43
Uo 28 V IIC
Io 125 mA IIB 640 nF
Po 0.88 W IIA 2.1 μF
Modul 9203B2A
Terminal 41-44
Uo 28 V IIC
Io 135 mA IIB 640 nF
Po 0.95 W IIA 2.1 μF
Terminal (11,12 and 13,14)
Input:
Voltage max. 28 VDC
Trig: NPN Low < 2 V, High > 4 V
Trig: PNP Low < 8 V, High > 10 V
Zone 2 installation
32 VAC / 32 VDC
16 VA / 32 W
0.5 AAC / 1 ADC
Prepared by:
PB
9203QI01
Co Lo Lo/Ro
2.69 mH 44 μH/Ω
10.8 mH 176 μH/Ω
20.8 mH 353 μH/Ω
Co Lo Lo/Ro
9.1 mH 162 μH/Ω
17.6 mH 325 μH/Ω
Co Lo Lo/Ro
7.8 mH 150 μH/Ω
15.1 mH 301 μH/Ω
Page:
2/2
23